d/freebsd-skq
1
0
Fork 0
Code Issues Pull Requests Packages Projects Releases Wiki Activity

Typo fixes and some language/punctuation improvements.

Browse Source
This commit is contained in:
Christian Brueffer 2014-05-11 10:06:27 +00:00
parent 4541f27356
commit 3b4afe73d0
1 changed files with 12 additions and 12 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

24
share/man/man4/lm75.4
View File

@ -24,7 +24,7 @@
.\"
.\" $FreeBSD$
.\"
.Dd March 7, 2014
.Dd May 11, 2014
.Dt LM75 4
.Os
.Sh NAME
@ -69,28 +69,28 @@ dev.lm75.0.shutdown: 0
Is the read-only value of the current temperature read by the sensor.
.It Va dev.lm75.%d.thyst
Sets the hysteresis temperature.
Once the temperature get over the overtemperature shutdown value (tos)
it need to drop bellow the hysteresis temperature to disable the output
Once the temperature gets over the overtemperature shutdown value (tos)
it needs to drop below the hysteresis temperature to disable the output
(interrupt) pin again.
.It Va dev.lm75.%d.tos
Sets the overtemperature shutdown value.
Once the temperature get over this value the output pin will be enabled.
Once the temperature gets over this value the output pin will be enabled.
The way the output (interrupt) pin works, depends on the mode configuration.
.It Va dev.lm75.%d.faults
Is the number of faults that must occur consecutively to activate the
interrupt (output) pin.
It can be set to 1, 2, 4, and 6.
.It Va dev.lm75.%d.mode
Set the operation mode for the sensor interrupt pin.
Sets the operation mode for the sensor interrupt pin.
It can be set to 'comparator' (default) or 'interrupt'.
.It Va dev.lm75.%d.polarity
Set the polarity of the sensor interrupt pin.
Sets the polarity of the sensor interrupt pin.
It can be set to 'active-low' (default) or 'active-high'.
Please note that the output pin is an open-drain output and it needs a
proper pull-up resistor to work.
.It Va dev.lm75.%d.shutdown
When set to '1' it shutdown the sensor.
The temperature convertion stops but the sensor remains with its i2c bus
When set to '1' it shuts down the sensor.
The temperature conversion stops but the sensor remains with its i2c bus
active, i.e., it can be woken up by setting this option to '0' again.
.El
.Pp
@ -124,7 +124,7 @@ On a
.Xr device.hints 5
based system, like
.Li MIPS ,
these values are configurable for the
these values are configurable for
.Nm :
.Bl -tag -width ".Va hint.lm75.%d.addr"
.It Va hint.lm75.%d.at
@ -168,7 +168,7 @@ property indicates which i2c address the
.Nm
is wired at.
.Nm
temperature sensors can be wired to 8 different address, allowing up to 8
temperature sensors can be wired to 8 different addresses, allowing up to 8
sensors on the same
.Xr iicbus 4 .
.El
@ -187,5 +187,5 @@ driver first appeared in
.An -nosplit
The
.Nm
driver and this manual page was written by
.An Luiz Otavio O Souza Aq loos@FreeBSD.org
driver and this manual page were written by
.An Luiz Otavio O Souza Aq loos@FreeBSD.org .