Removed the NSECS_MULTI option, and implemented both 32 bit probe
enable and multi-sector I/O enable by using the controller or device flags capability. Per a suggestion by phk.
This commit is contained in:
John Dyson
parent
d996508637
commit
e3dd31586c
@ -2,7 +2,7 @@
|
||||
# LINT -- config file for checking all the sources, tries to pull in
|
||||
# as much of the source tree as it can.
|
||||
#
|
||||
# $Id: LINT,v 1.171 1995/04/22 22:39:33 dyson Exp $
|
||||
# $Id: LINT,v 1.172 1995/04/23 18:30:26 wollman Exp $
|
||||
#
|
||||
# NB: You probably don't want to try running a kernel built from this
|
||||
# file. Instead, you should start from GENERIC, and add options from
|
||||
@ -388,9 +388,6 @@ controller isa0
|
||||
# TUNE_1542 enables the automatic ISA bus speed selection for the
|
||||
# Adaptec 1542 boards. Does not work for all boards, use it with caution.
|
||||
#
|
||||
# NSECS_MULTI enables and allows multi-block transfers in the wd driver.
|
||||
# suggested values would be 8 or 16.
|
||||
#
|
||||
#options ALLOW_CONFLICT_DRQ
|
||||
#options ALLOW_CONFLICT_IOADDR
|
||||
#options ALLOW_CONFLICT_IRQ
|
||||
@ -400,7 +397,6 @@ options "AUTO_EOI_1"
|
||||
options BOUNCE_BUFFERS
|
||||
#options DUMMY_NOPS
|
||||
#options "TUNE_1542"
|
||||
#options "NSECS_MULTI=16"
|
||||
|
||||
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
|
||||
#device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint
|
||||
@ -467,6 +463,30 @@ controller wds0 at isa? port 0x350 bio irq 15 drq 6 vector wdsintr
|
||||
# ST-506, ESDI, and IDE hard disks: `wdc' and `wd'
|
||||
#
|
||||
# NB: ``Enhanced IDE'' is NOT supported at this time.
|
||||
#
|
||||
# The flags fields are used to enable the multi-sector I/O and
|
||||
# the 32BIT I/O modes. The flags may be used in either the controller
|
||||
# definition or in the individual disk definitions. The controller
|
||||
# definition is supported for the boot configuration stuff.
|
||||
#
|
||||
# Each drive has a 16 bit flags value defined:
|
||||
# The low 8 bits are the maximum value for the multi-sector I/O,
|
||||
# where 0xff defaults to the maximum that the drive can handle.
|
||||
# The high bit of the 16 bit flags (0x8000) allows probing for
|
||||
# 32 bit transfers.
|
||||
#
|
||||
# The flags field for the drives can be specified in the controller
|
||||
# specification with the low 16 bits for drive 0, and the high 16 bits
|
||||
# for drive 1.
|
||||
# e.g.:
|
||||
#controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x00ff8004 vector wdintr
|
||||
#
|
||||
# specifies that drive 0 will be allowed to probe for 32 bit transfers and
|
||||
# a maximum multi-sector transfer of 4 sectors, and drive 1 will not be
|
||||
# allowed to probe for 32 bit transfers, but will allow multi-sector
|
||||
# transfers up to the maximum that the drive supports.
|
||||
#
|
||||
|
||||
#
|
||||
controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr
|
||||
disk wd0 at wdc0 drive 0
|
||||
|
||||
@ -2,7 +2,7 @@
|
||||
# LINT -- config file for checking all the sources, tries to pull in
|
||||
# as much of the source tree as it can.
|
||||
#
|
||||
# $Id: LINT,v 1.171 1995/04/22 22:39:33 dyson Exp $
|
||||
# $Id: LINT,v 1.172 1995/04/23 18:30:26 wollman Exp $
|
||||
#
|
||||
# NB: You probably don't want to try running a kernel built from this
|
||||
# file. Instead, you should start from GENERIC, and add options from
|
||||
@ -388,9 +388,6 @@ controller isa0
|
||||
# TUNE_1542 enables the automatic ISA bus speed selection for the
|
||||
# Adaptec 1542 boards. Does not work for all boards, use it with caution.
|
||||
#
|
||||
# NSECS_MULTI enables and allows multi-block transfers in the wd driver.
|
||||
# suggested values would be 8 or 16.
|
||||
#
|
||||
#options ALLOW_CONFLICT_DRQ
|
||||
#options ALLOW_CONFLICT_IOADDR
|
||||
#options ALLOW_CONFLICT_IRQ
|
||||
@ -400,7 +397,6 @@ options "AUTO_EOI_1"
|
||||
options BOUNCE_BUFFERS
|
||||
#options DUMMY_NOPS
|
||||
#options "TUNE_1542"
|
||||
#options "NSECS_MULTI=16"
|
||||
|
||||
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
|
||||
#device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint
|
||||
@ -467,6 +463,30 @@ controller wds0 at isa? port 0x350 bio irq 15 drq 6 vector wdsintr
|
||||
# ST-506, ESDI, and IDE hard disks: `wdc' and `wd'
|
||||
#
|
||||
# NB: ``Enhanced IDE'' is NOT supported at this time.
|
||||
#
|
||||
# The flags fields are used to enable the multi-sector I/O and
|
||||
# the 32BIT I/O modes. The flags may be used in either the controller
|
||||
# definition or in the individual disk definitions. The controller
|
||||
# definition is supported for the boot configuration stuff.
|
||||
#
|
||||
# Each drive has a 16 bit flags value defined:
|
||||
# The low 8 bits are the maximum value for the multi-sector I/O,
|
||||
# where 0xff defaults to the maximum that the drive can handle.
|
||||
# The high bit of the 16 bit flags (0x8000) allows probing for
|
||||
# 32 bit transfers.
|
||||
#
|
||||
# The flags field for the drives can be specified in the controller
|
||||
# specification with the low 16 bits for drive 0, and the high 16 bits
|
||||
# for drive 1.
|
||||
# e.g.:
|
||||
#controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x00ff8004 vector wdintr
|
||||
#
|
||||
# specifies that drive 0 will be allowed to probe for 32 bit transfers and
|
||||
# a maximum multi-sector transfer of 4 sectors, and drive 1 will not be
|
||||
# allowed to probe for 32 bit transfers, but will allow multi-sector
|
||||
# transfers up to the maximum that the drive supports.
|
||||
#
|
||||
|
||||
#
|
||||
controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr
|
||||
disk wd0 at wdc0 drive 0
|
||||
|
||||
@ -2,7 +2,7 @@
|
||||
# LINT -- config file for checking all the sources, tries to pull in
|
||||
# as much of the source tree as it can.
|
||||
#
|
||||
# $Id: LINT,v 1.171 1995/04/22 22:39:33 dyson Exp $
|
||||
# $Id: LINT,v 1.172 1995/04/23 18:30:26 wollman Exp $
|
||||
#
|
||||
# NB: You probably don't want to try running a kernel built from this
|
||||
# file. Instead, you should start from GENERIC, and add options from
|
||||
@ -388,9 +388,6 @@ controller isa0
|
||||
# TUNE_1542 enables the automatic ISA bus speed selection for the
|
||||
# Adaptec 1542 boards. Does not work for all boards, use it with caution.
|
||||
#
|
||||
# NSECS_MULTI enables and allows multi-block transfers in the wd driver.
|
||||
# suggested values would be 8 or 16.
|
||||
#
|
||||
#options ALLOW_CONFLICT_DRQ
|
||||
#options ALLOW_CONFLICT_IOADDR
|
||||
#options ALLOW_CONFLICT_IRQ
|
||||
@ -400,7 +397,6 @@ options "AUTO_EOI_1"
|
||||
options BOUNCE_BUFFERS
|
||||
#options DUMMY_NOPS
|
||||
#options "TUNE_1542"
|
||||
#options "NSECS_MULTI=16"
|
||||
|
||||
# Enable this and PCVT_FREEBSD for pcvt vt220 compatible console driver
|
||||
#device vt0 at isa? port "IO_KBD" tty irq 1 vector pcrint
|
||||
@ -467,6 +463,30 @@ controller wds0 at isa? port 0x350 bio irq 15 drq 6 vector wdsintr
|
||||
# ST-506, ESDI, and IDE hard disks: `wdc' and `wd'
|
||||
#
|
||||
# NB: ``Enhanced IDE'' is NOT supported at this time.
|
||||
#
|
||||
# The flags fields are used to enable the multi-sector I/O and
|
||||
# the 32BIT I/O modes. The flags may be used in either the controller
|
||||
# definition or in the individual disk definitions. The controller
|
||||
# definition is supported for the boot configuration stuff.
|
||||
#
|
||||
# Each drive has a 16 bit flags value defined:
|
||||
# The low 8 bits are the maximum value for the multi-sector I/O,
|
||||
# where 0xff defaults to the maximum that the drive can handle.
|
||||
# The high bit of the 16 bit flags (0x8000) allows probing for
|
||||
# 32 bit transfers.
|
||||
#
|
||||
# The flags field for the drives can be specified in the controller
|
||||
# specification with the low 16 bits for drive 0, and the high 16 bits
|
||||
# for drive 1.
|
||||
# e.g.:
|
||||
#controller wdc0 at isa? port "IO_WD1" bio irq 14 flags 0x00ff8004 vector wdintr
|
||||
#
|
||||
# specifies that drive 0 will be allowed to probe for 32 bit transfers and
|
||||
# a maximum multi-sector transfer of 4 sectors, and drive 1 will not be
|
||||
# allowed to probe for 32 bit transfers, but will allow multi-sector
|
||||
# transfers up to the maximum that the drive supports.
|
||||
#
|
||||
|
||||
#
|
||||
controller wdc0 at isa? port "IO_WD1" bio irq 14 vector wdintr
|
||||
disk wd0 at wdc0 drive 0
|
||||
|
||||
Loading…
Reference in New Issue
Block a user