Due to hardware errata in Aero controllers, reads to certain
fusion registers could intermittently return all zeroes.
This behavior is transient in nature and subsequent reads will return
valid value.
Fix:
For Aero controllers, any read will retry the read operations
from certain registers for maximum three times, if read returns zero.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
For Aero adapters-
1. Driver will use 32 bit atomic descriptor to fire IOs and DCMDs.
2. Driver will use 64 bit request descriptor to fire IOC INIT.
3. If Aero firmware supports 32 bit atomic descriptor, then only driver will use it
otherwise driver will use 64 bit request descriptor.
For rest of adapters(Ventura, Invader and Thunderbolt), driver will use 64 bit request
descriptors only.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
Driver will throw a warning message when a Configurable secure type controller is
encountered.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
very minimal prints and even few important messages will not get logged.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
capable IOs. NVME specification supports specific type of scatter gather list
called as PRP (Physical Region Page) for IO data buffers. Since NVME drive is
connected behind SAS3.5 tri-mode adapter, MegaRAID driver/firmware has to convert
OS SGLs in native NVMe PRP format. For IOs sent to firmware, MegaRAID firmware
does this job of OS SGLs to PRP translation and send PRPs to backend NVME device.
For fastpath IOs, driver will do this OS SGLs to PRP translation.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
required Write IOs as Fast Path IOs (after the appropriate checks
allowing Fast Path to be used) to the appropriate physical drives
(translated from the OS logical IO) and wait for all Write IOs to complete.
Design: A write IO on RAID volume will be examined if it can be sent in
Fast Path based on IO size and starting LBA and ending LBA falling on to
a Physical Drive boundary. If the underlying RAID volume is a RAID 1/10,
driver issues two fast path write IOs one for each corresponding physical
drive after computing the corresponding start LBA for each physical drive.
Both write IOs will have the same payload and are posted to HW such that
replies land in the same reply queue.
If there are no resources available for sending two IOs, driver will send
the original IO from upper layer to RAID volume through the Firmware.
When both IOs are completed by HW, the resources will be released
and SCSI IO completion handler will be called.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
stream to help HBA Firmware do the Full Stripe Writes. For read IOs on
certain RAID volumes like Read Ahead volumes,this will help driver to
send it to Firmware even if the IOs can potentially be sent to
hardware directly (called fast path) bypassing firmware.
Design: 8 streams are maintained per RAID volume as per the combined
firmware/driver design. When there is no stream detected the LRU stream
is used for next potential stream and LRU/MRU map is updated to make this
as MRU stream. Every time a stream is detected the MRU map
is updated to make the current stream as MRU stream.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
for different number of supported VDs for SAS3.5 MegaRAID adapters.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
Approved by: ken
MFC after: 3 days
Sponsored by: Broadcom Inc
opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
Uses of mallocarray(9).
The use of mallocarray(9) has rocketed the required swap to build FreeBSD.
This is likely caused by the allocation size attributes which put extra pressure
on the compiler.
Given that most of these checks are superfluous we have to choose better
where to use mallocarray(9). We still have more uses of mallocarray(9) but
hopefully this is enough to bring swap usage to a reasonable level.
Reported by: wosch
PR: 225197
Focus on code where we are doing multiplications within malloc(9). None of
these is likely to overflow, however the change is still useful as some
static checkers can benefit from the allocation attributes we use for
mallocarray.
This initial sweep only covers malloc(9) calls with M_NOWAIT. No good
reason but I started doing the changes before r327796 and at that time it
was convenient to make sure the sorrounding code could handle NULL values.
The sim_vid, hba_vid, and dev_name fields of struct ccb_pathinq are
fixed-length strings. AFAICT the only place they're read is in
sbin/camcontrol/camcontrol.c, which assumes they'll be null-terminated.
However, the kernel doesn't null-terminate them. A bunch of copy-pasted code
uses strncpy to write them, and doesn't guarantee null-termination. For at
least 4 drivers (mpr, mps, ciss, and hyperv), the hba_vid field actually
overflows. You can see the result by doing "camcontrol negotiate da0 -v".
This change null-terminates those fields everywhere they're set in the
kernel. It also shortens a few strings to ensure they'll fit within the
16-character field.
PR: 215474
Reported by: Coverity
CID: 1009997 1010000 1010001 1010002 1010003 1010004 1010005
CID: 1331519 1010006 1215097 1010007 1288967 1010008 1306000
CID: 1211924 1010009 1010010 1010011 1010012 1010013 1010014
CID: 1147190 1010017 1010016 1010018 1216435 1010020 1010021
CID: 1010022 1009666 1018185 1010023 1010025 1010026 1010027
CID: 1010028 1010029 1010030 1010031 1010033 1018186 1018187
CID: 1010035 1010036 1010042 1010041 1010040 1010039
Reviewed by: imp, sephe, slm
MFC after: 4 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9037
Differential Revision: https://reviews.freebsd.org/D9038
passing it to firmware for all Gen3 controllers.
For Thunderbolt controller, keep the legacy behavior i.e. return the SYNCHRONIZE_CACHE command with success status from driver itself.
There is Sysctl parameter 'block_sync_cache' is provided to enable customers either to block/unblock these commands to facilitate
legacy behavior if there is a compatibility issue. Default value for module parameter is to unblock this command.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies
and return without processing event in AEN thread, if controller reset is in progress.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies
If a SCSI IO times out, then before initiating OCR, now the driver will try to send a
target reset to the particular target for which the IO is timed out. If that also fails,
then the driver will initiate OCR.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies
Did the same by setting sc->aen_cmd = NULL when aborting AEN is successful.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies
MFI linked list in megaraid_sas driver is used for mfi-mpt pass-through commands.
This list can be corrupted due to many possible race conditions in driver and
eventually we may see kernel panic.
One example -
MFI frame is freed from calling process as driver send command via polling method and interrupt
for that command comes after driver free mfi frame (actually even after some other context reuse
the mfi frame). When driver receive MPT frame in ISR, driver will be using the index of MFI and
access that MFI frame and finally in-used MFI frames list will be corrupted.
High level description of new solution -
Free MFI and MPT command from same context.
Free both the command either from process (from where mfi-mpt pass-through was called) or from
ISR context. Do not split freeing of MFI and MPT, because it creates the race condition which
will do MFI/MPT list.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: Broadcom Limited/AVAGO Technologies
NOTE:
The FreeBSD system currently restricts the MAX IO size to MAXPHYS which
in turn is 128KB. We tested the 1MB IO by converting the MAXPHYS to 1MB.
Following is the mail reference:
http://lists.freebsd.org/pipermail/freebsd-scsi/2015-January/006568.html
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies
JBODs. Driver has to sync the JBOD map with firmware and use sequence number
as a reference for JBOD FastPath I/O's.
Submitted by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed by: Kashyap Desai <Kashyap.Desai@broadcom.com>
MFC after: 3 days
Sponsored by: AVAGO Technologies
Switch from make_dev_alias to make_dev_alias_p since make_dev_alias_p can
gracefully fail if the /dev/megaraid_sas_ioctl_node symlink already exists.
This can happen if mfi(4) and mrsas(4) are both attached to cards and
providing Linux emulation support. Let the first one win. An equivalent
change has been done in mfi(4). Extra credit would be to pass the
Linux emulation call to the other driver when appropriate. This will
probably be a rare case and the user can manually change where the symlink
points to.
MFC after: 3 days
and there are some pending IOs at the time of OCR. This is mainly because of
recursive mutext in OCR and IO completion function call. Generic IO completion (from ISR) needs
sim_lock to be held before it calls completion to CAM (xpt_done), but in case of OCR path mrsas_ocr thread
itself take sim_lock, so this condition is now handled in this patch.
MFC after: 3 days
