instead of POSTREAD: the hardware do not touch this memory (CPU
updates it). It is already synchronized as PREWRITE after the
processing is done.
- Synchronize RX return ring memory in rx_eof. This is needed
as the deviced updates this memory when receives packets.
- Decouple the synchronization of BGE status block in the interrupt
service routine: perfrom PREREAD synchronization only all accesses
to this block are finished. This seems to be more natural.
Reviewed by: yongari, marius
MFC after: 2 weeks
to the lock we hold, disable interrupts, and announce to the firmware
that we are shutting down. Especially do this before disabling blocks.
This makes some types of machines with asf enabled no longer hang upon
boot, when we start configuring the interface.
PR: i386/96382, kern/100410, kern/122252, kern/116328
Reported by: erwin
Hardware provided by: TDC A/S
Reviewed by: stas
Tested by: stas
BGE_PCI_PRODID_ASICREV register to store the chip identifier and its revision.
- Add new grouping macro for 7575+ chips (BGE_IS_5755_PLUS).
- Add IDs for Fujitsu-branded Broadcom adapters.
PR: kern/127587
Tested by: Thomas Quinot <thomas@quinot.org> (BCM7561 A0)
MFC after: 2 weeks
Obtained from: OpenBSD
loop iteration as it can be updated by the card while we
process the RX ring forcing us to process RX descriptors
for which DMA synchronisation operation has not been
performed. This fixes the bug when bge(4) drops packets
under high load.
Discussed with: yongari, marius
Approved by: re (kib)
MFC after: 1 week
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
CPU for too long period than necessary. Additively, interfaces are kept
polled (in the tick) even if no more packets are available.
In order to avoid such situations a new generic mechanism can be
implemented in proactive way, keeping track of the time spent on any
packet and fragmenting the time for any tick, stopping the processing
as soon as possible.
In order to implement such mechanism, the polling handler needs to
change, returning the number of packets processed.
While the intended logic is not part of this patch, the polling KPI is
broken by this commit, adding an int return value and the new flag
IFCAP_POLLING_NOCOUNT (which will signal that the return value is
meaningless for the installed handler and checking should be skipped).
Bump __FreeBSD_version in order to signal such situation.
Reviewed by: emaste
Sponsored by: Sandvine Incorporated
drops and re-grabs the softc mutex in the middle, resulting in kernel
trap 12. This may happen when a lot of traffic is being hammered on
one bge(4) interface while the system is shutting down.
Reported by: Alexander Sack <pisymbol gmail com>
PR: kern/134548
MFC After: 2 weeks
quirk requiring it to be enabled even when using MSI. This makes
the latter work again after r189285.
- Remove a comment which no longer applies since r190194.
- If boot verbose, print asicrev, chiprev and bus type on attach.
- For PCI Express devices:
1) Adjust max read request size to 4Kbytes
2) Turn on FIFO_LONG_BURST in RDMA during bge_blockinit()
Though 1) does not seem to have much to do with the poor TX performance
observed on PCI Express bge(4), 2) does fix the problem. [1]
- Nuke the RX CPU self-diag, which prevents working cards from working
(Linux tg3 does not have this diag neither does OpenBSD's bge(4)).
The increasing of the firmware handshaking timeout to 20000 retries
done as part of the original commit isn't merged as way already have a
way higher BGE_TIMEOUT of 100000.
PR: 119361 [1]
Obtained from: tg3 via DragonflyBSD [1], DragonflyBSD
causes data corruption in combination with certain bridges.
Information about this problem was kindly provided by davidch. [1]
- As BGE_FLAG_PCIX is meant to indicate that the controller is in
PCI-X mode, revert to the pre __FreeBSD_version 602101 method of
reading the bus mode register rather than checking the mere
existence of a PCI-X capability, which is also there when the
NIC f.e. is put into a 32-bit slot causing it not to be in PCI-X
mode. Setting BGE_FLAG_PCIX inappropriately could cause the NIC
to be tuned incorrectly.
PR: 128833 [1]
Reviewed by: jhb
MFC after: 3 days
for the BCM5714 revision A0 when in a multi-port configuration
and unconditionally for the remainder of the class of BCM575X
and beyond chips.
This was prodded by mav and is based on a suggestion and a
patch submitted by jhb.
Reviewed by: jhb
MFC after: 2 months
containing an Ethernet address fitted as this is yet another thing
that fails in that case in order to avoid the one second delay
until pci_read_vpd_reg() times out.
- Const'ify the bge_devs array.
- Rename BGE_FLAG_EEPROM to BGE_FLAG_EADDR to underline it's absence means
"there's no chip containing an Ethernet address fitted to the BGE chip
so we have to get it from the firmware instead" rather than "there's no
EEPROM, but maybe NVRAM or something else".
- Don't treat BCM5906[M] generally like chips w/o BGE_FLAG_EADDR set, just
in the two cases really necessary. This gets us line with the original
patch for DragonFlyBSD.
- For sparc64 restore the intended behavior of obtaining the Ethernet
address from the firmware in case BGE_FLAG_EADDR is not set, even for
BCM5906[M].
- Fix some style(9) bugs introduced with rev. 1.208 of if_bge.c
Approved by: jhb
Additional testing by: Thomas Nystroem (BCM5906)
all cards/modes.
In addition to the intr forcing added with rev. 1.205 adopt the other
places to use the same logic.
We need to exclude a few chips/revisions (5700, 5788) from using the
enhanced version and fall back to the old way as that is the only
method they support.
Tested by: phk
Suggested by: davidch, Broadcom (thanks a lot for the help!)
MFC after: 16 days
10/100 operation and place the mailbox registers at a different offset.
They also do not have an EEPROM, so the MAC address must be read from
NVRAM instead.
MFC after: 1 month
PR: kern/118975
Submitted by: benjsc, Thomas Nyström thn at saeab dot se
Submitted by: sephe (original patch for DragonflyBSD)
when creating the parent bus DMA tag. While at it correct the style
and a nearby comment.
- Take advantage of m_collapse(9) for performance reasons.
MFC after: 2 weeks
Because of this we were not getting further interrupts for link state
changes, thus never went into iface UP state and thus could not transmit.
The only way out of this was an incoming packet generating an rx interrupt
and making us call into bge_link_upd.
Up to rev. 1.101, in bge_start_locked, we only returned instantly
if there was 'no link AND nothing queued for tx'. So with a packet queued
for tx, we hit the register scrubbing at the end of bge_start_locked
and were out fine. We simply lost a packet or two but got the interrupts
need to get into UP state.
With rev. 1.102 this was turned into 'if there is no link OR there is
nothing to send' (correct behaviour) and as long as there is no link
we never hit the register scrubbing and consequently never got the link UP.
What we do now is force an interrupt at the end of bge_ifmedia_upd_locked
so we will call bge_link_upd, clear the link state attention and get
further interrupts.
This helps to get the iface UP on an idle network or at least to get
it UP faster not depending on an rx intr anymore.
In case you could not get a DHCP lease or it took very long,
it was because of this.
It is unknown which chips are affected by this. ASIC rev. 0x2003 was the
most popular trouble candidate.
At least the fiber cards should have been working fine.
Which register to scrub is currently under discussion. The comitted
solution was tested and found to work for a lot of setups. It might
not help with MSI.
The reason why we end up in such a situation is entirely unknown.
PR: kern/111804
Tested by: phk, scottl at Y!
MFC after: 14 days
The register layout is little different from memory-mapped stats
in the previous generation chips. In fact, it is bad because
registers in this range are cleared after reading them.
Reviewed by: scottl
MFC after: 3 days
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
sysctl_handle_int is not sizeof the int type you want to export.
The type must always be an int or an unsigned int.
Remove the instances where a sizeof(variable) is passed to stop
people accidently cut and pasting these examples.
In a few places this was sysctl_handle_int was being used on 64 bit
types, which would truncate the value to be exported. In these
cases use sysctl_handle_quad to export them and change the format
to Q so that sysctl(1) can still print them.
Blade 2500, Fire V210 and probably some other sparc64 machines.
These chips are typically not fitted with an EEPROM which means
that we have to obtain the MAC address via OFW and that some chip
tests will just always fail.
These changes are based on the respective code found in OpenBSD
with some additional info obtained from OpenSolaris and some style
suggestions by jkim@. They also have the desired side-effect of
respecting the 'local-mac-address?' system configuration variable
for the affected BGEs.
- In bge_attach() factor out calling bge_release_resources() before
going to the fail label into the fail label as well as replace a
magic 6 with ETHER_ADDR_LEN.
Reviewed by: yongari (before style changes), jkim
