ATA specification declares minimal reset time of 5us. SATA keeps it, but
requires devices to handle commands transmitted even one by one without
any gap.
as ATA RAID, but generic ATAPCI driver unable to detect drives there. AHCI
driver reported to handle them fine. Linux does the same.
Submitted by: Andrey V. Elsukov on stable@
This fixes the low "max device openings" count that has lead to poor
performance in FreeBSD 7.0 and 7.1.
Extra thanks goes to Mike Tancsa at Sentex for providing a debug system for
this.
This is triggered only if BIOS configures ACPI_BITREG_BUS_MASTER_RLD
aka BRLD_EN_BM to 1.
Rationale:
1. we do not support C3 on PIIX4E
2. bus master activity need not break out of C2 state
3. because of CPU_QUIRK_NO_BM_CTRL quirk we may reset bus master
status which would result in immediate break out from C2
So if you have seen
cpu0: too many short sleeps, backing off to C1
with this chipset before you may want to try cx_lowest of C2 again.
Reviewed by: rpaulo (mentor), njl
Approved by: rpaulo (mentor)
ata_detach() to implement IOCATAATTACH/IOCATADETACH ioctls.
This will permit channel drivers to properly shutdown port hardware on channel
detach and init it on attach.
o mark phy type to indicate 1/2 or 1/4-rate operation
o use phy type instead of channel attributes to identify 1/2 and 1/4-rate
operation
o general cleanup of code including move phy constants to ah_internal.h
Eventually this code should go away and we should use the net0211 equivalents.
the old TTY implementation; however, take a cut at stripping its
optional Giant-protected code paths enabled using debug.cx.mpsafenet,
which will no longer work once IFF_NEEDSGIANT is removed.
join allocate() and dmainit() atapci subdriver's channel initialization
methods into single ch_attach() method.
As opposite to ch_attach() add new ch_detach() method to deallocate/disable
channel.
it instead of overloading sbp_show_sdev_info().
replace calls to printf with calls to device_printf and cleanup debug
messages
Remove a bit of dead, commented out code.
Reviewed by: scottl(mentor)
MFC after: 2 weeks
- Update to firmware 1.4.39 for dual-chip NIC (10G-PCIE2-xxx)
support, and SFP+ i2c support
- Identify newer "B" NICs (10G-PCIEx-8B-x) correctly, rather than
mis-identifying them as "A" NICs (cosmetic only)
- Identify the IFM_10G_LRM ifmedia type, where applicable.
- Identify ifmedia types for SFP+ based NICs
- Update copyright
Sponsored by: Myricom
MFC after: 1 week
Deprecate unused phy_delay Self ID field as it was removed
by 1394a-2000.
Attempt to parse extended Self ID PHY packets if they are detected
Reviewed by: scottl (mentor)
MFC after: 2 weeks
interesting conditional printf's into single device_printf's
Change a couple of variable names so that I don't have to trace what they
acutally do anymore.
Enable the display of the Self ID PHY packet if firewire_debug > 0
Reviewed by: scottl(mentor)
MFC after: 2 weeks
Prior to this fix, IEVENT register was always cleared before calling
tsec_error_intr_locked(), which prevented error recovery actions from
happening with polling enabled (and could lead to serious problems, including
controller hang).
Submitted by: Marcin Ligenza marcinl ! pacomp dot com dot pl
- interrupt coalescing
- polling
- jumbo frames
- multicast
- VLAN tagging
The enhanced version of the chip (eTSEC) can also take advantage of:
- TCP/IP checksum calculation h/w offloading
Obtained from: Freescale, Semihalf
If speed of link between two devices is slower than the reported max
speed of both endpoints, the current driver will fail and be unable to
negotiate.
Summary:
Test negotiated speed by reading the CSRROM into a dummy variable.
If that read fails, decrement our speed and retry. If all else fails,
go to lowest speed possible(0).
Report speed to the user.
Add display of the Bus Info Block when debug.firewire_debug > 1
Support the Bus Info Block(1394a-2000) method of speed detection.
I also should note that I am moving "hold_count" to 0 for future
releases.
This variable determines how many bus resets to "hold" a removed
firewire device before deletion. I don't feel this is useful and will
probably drop support for this sysctl in the future.
Reviewed by: scottl(mentor)
MFC after: 2 weeks
almost once. After we've configured the devices that were present the
first time through, then we know that we're done. If the device has
other devices that are deferred, then it must do a similar dance.
This catches both PC Cards and CardBus cards.
to not allocate them after the recent ata channels enumeration changes.
It allows to save some resources, not bother user with unexisting hardware
and not check unimplemented ports status on every interrupt.
Works fine with AHCI and theoretically other MSI capable devices.
At this moment support disabled by default. To enable it, set
"hint.atapci.X.msi=1" device hint.
