Some files keep the SUN4V tags as a code reference, for the future,
if any rewamped sun4v support wants to be added again.
Reviewed by: marius
Tested by: sbruno
Approved by: re
architectures (i386, for example) the virtual memory space may be
constrained enough that 2MB is a large chunk. Use 64K for arches
other than amd64 and ia64, with special handling for sparc64 due to
differing hardware.
Also commit the comment changes to kmem_init_zero_region() that I
missed due to not saving the file. (Darn the unfamiliar development
environment).
Arch maintainers, please feel free to adjust ZERO_REGION_SIZE as you
see fit.
Requested by: alc
MFC after: 1 week
MFC with: r221853
for the AR9280 based NICs if it's actually enabled.
Some of the OLC code was erroneously called during setup
and calibration. This may have caused some incorrect behaviour.
Xen timer and time counter to provide one-shot and periodic time events.
On my tests this reduces idle interruts rate down to about 30Hz, and accor-
ding to Xen VM Manager reduces host CPU load by three times comparing to
the previous periodic 100Hz clock. Also now, when needed, it is possible to
increase HZ rate without useless CPU burning during idle periods.
Now only ia64 and some ARMs left not migrated to the new event timers.
table which contains the per-rate target TX power.
This code is shared between the v14 eeprom board setup (AR5416, AR9160,
AR9280) and will also be used by the upcoming Kite (AR9287) support.
* grab the main, alt and selected LNA config
* add some optional / disabled logging code
* add a check to reject packets with an invalid main rssi too,
in case the alt is the active receive chain and main is -ve.
Note: The software-controlled combined diversity code is still disabled.
should not change. Fetch the td_user_pri under the thread lock. This
is probably not necessary but a magic number also seems preferable to
knowing the implementation details here.
Requested by: Jason Behmer < jason DOT behmer AT isilon DOT com >
- Use bus_bind_intr() to bind interrupt to a CPU when RSS/TSS is used.
- Use M_DONTWAIT for RSS/TSS buffer allocation.
- Add statistic to track max DRBR queue depth.
- Fix problem in bxe_change_mtu() which referenced the old MTU size
in a debug print statement.
MFC after: Two weeks
disabled for BCM5719 A0 revision due to known hardware errata.
Many thanks to Broadcom for continuing support of FreeBSD.
Submitted by: Geans Pin at Broadcom
AR8132 FastEthernet controller. The PHY has no ability to
establish a gigabit link. Previously only link parters which
support down-shifting was able to establish link.
This change should fix a long standing link establishment issue of
AR8132.
PR: kern/156935
MFC after: 1 week
Casting a pointer to a wide integer is probably not that bad, but I am
still guilty of not testing this.
Pointyhat to: avg
MFC after: 1 week
X-MFC with: r221803
file and processes information retrieval from the running kernel via sysctl
in the form of new library, libprocstat. The library also supports KVM backend
for analyzing memory crash dumps. Both procstat(1) and fstat(1) utilities have
been modified to take advantage of the library (as the bonus point the fstat(1)
utility no longer need superuser privileges to operate), and the procstat(1)
utility is now able to display information from memory dumps as well.
The newly introduced fuser(1) utility also uses this library and able to operate
via sysctl and kvm backends.
The library is by no means complete (e.g. KVM backend is missing vnode name
resolution routines, and there're no manpages for the library itself) so I
plan to improve it further. I'm commiting it so it will get wider exposure
and review.
We won't be able to MFC this work as it relies on changes in HEAD, which
was introduced some time ago, that break kernel ABI. OTOH we may be able
to merge the library with KVM backend if we really need it there.
Discussed with: rwatson
This brings our implementation in line with OSS specification for
systems that support mmap. The change should also improve compatibility
with OSS software not specifically written for FreeBSD, e.g. PulseAudio
OSS plugin.
Reviewed by: kib, jhb
MFC after: 1 week
probed and read successfull, but it contains invalid values (e.g.
overlapped partitions, offset or size is out of bounds), then table
will be rejected.
MFC after: 1 month
* revert a local path change that shouldn't have made it to the commit
* fix some indenting/wrapping
* Fix the ale data copy - i should be copying into the ale data pointer,
not over the ale entry itself.
environments.
In setups where NF calibration can take a while, don't load the CCA
and kick off a new NF calibration if the previous one hasn't yet
completed. This shouldn't happen unless the environment is noisy but
those exist (hi phk!).
Here, if the previous NF hasn't completed when ar5416LoadNf() is run
(which reads the NF), it skips updating the history buffer, loading
the NF CCA array and kicking off the next NF cal. It's hoped it'll
occur in the next long calibration interval.
Obtained from: Atheros, ath9k, my local HAL
This is taking quite a while for some people in some situations
(eg AR5418 in phk's Abusive Radio Environment).
Instead, the rest of the calibration related code should
ensure that a NF calibration has occured before reading NF
values and kicking off another NF calibration.
The channel should also likely be marked as "noisy" (CWINT)
if the NF calibration takes too long.
CPU. This fixes a panic observed on Heathrow-based systems without
SMP-capable PICs when the kernel had both options SMP and INVARIANTS.
MFC after: 5 days
* Correct some of the silicon revision checks to match what
the Atheros HAL does. (See [1] below.)
* Move the PA cal and init cal method assignment to -after-
the mac version/revision IDs are stored. The AR9285 init
cal was never being called.
* Enable ANI.
Note Kite 1.0 and 1.1 were prototypes that shouldn't be seen
in the wild. Linux ath9k simply removed the prototype code from
their codebase. I'm going to leave it in there for now but
make it conditionally compilable in the future.
Obtained from: Atheros
newer controllers. However, all data sheet I have access has no
indication that buffer manager should not be touched on these
controllers. It seems the buffer manager always runs on BCM5705 or
newer controllers. Some controller(e.g. BCM5719) needs other buffer
manager configuration so driver should enable buffer manager for
all controllers. Both Linux and OpenBSD/NetBSD use the same
approach.
This change polls enable bit of block to know whether specified
block was really stopped as well as enabling buffer manager for all
controllers in driver initialization.
Obtained from: NetBSD
when the user has indicated that the system has synchronized TSCs or it has
P-state invariant TSCs. For the former case, we may clear the tunable if it
fails the test to prevent accidental foot-shooting. For the latter case, we
may set it if it passes the test to notify the user that it may be usable.
from Atheros as to what/when this is supposed to be enabled.
Using the default RX fast diversity settings seems to help quite
a bit.
Whilst I'm here, change the prototype to return HAL_BOOL rather than int.
I'm not sure whether we should install teken as a library on any stock
FreeBSD installation, but I can imagine people want to tinker around
with it now and then. Create a /sys/teken/libteken, which holds a
Makefile to install a shared library version of the terminal emulator,
complete with a manpage.
Also add Makefiles for the demo/stress applications, to build it against
the shared library.
For now, the diversity settings are controlled by 'txantenna',
-not- rxantenna. This is because the earlier chipsets had
controllable TX diversity; the RX antenna setting twiddles
the default antenna register. I'll try sort that stuff out at
some point.
Call the antenna switch function from the board setup function
so scans, channel changes, mode changes, etc don't set the
diversity back to a default state too far from what's intended.
Things to todo:
* Squirrel away the last antenna diversity/combining parameters
and restore them during board setup if HAL_ANT_VARIABLE is
defined. That way scans, etc don't reset the diversity settings.
* Add some more public facing statistics, rather than what's
simply logged under HAL_DEBUG_DIVERSITY.
For now, the fixed antenna settings behave better than variable
settings for me. I have some further fiddling to do..
Obtained from: Atheros
keep constant ISN growth rate, do the same directly inside tcp_new_isn(),
taking into account how much time (ticks) passed since the last call.
On my test systems this decreases idle interrupt rate from 140Hz to 70Hz.
The macro which I incorrectly copied into ah_internal.h assumed
that it'd be called with an AR_SREV_MERLIN_20() check to ensure
it was only enabled for Merlin (AR9280) silicon revision 2.0 or
later.
Trouble is, the 5GHz fast clock EEPROM flag is only valid for
EEPROM revision 16 or greater; it's assumed to be enabled
by default for Merlin rev >= 2.0. This meant it'd be incorrectly
set for AR5416 and AR9160 in 5GHz mode.
This would have affected non-default clock timings such as SIFS,
ACK and slot time. The incorrect slot time was very likely wrong
for 5ghz mode.
* Modify AR_SREV_MERLIN_20() to match the Atheros/Linux ath9k behaviour -
its supposed to match Merlin 2.0 and later Merlin chips.
AR_SREV_MERLIN_20_OR_LATER() matches AR9280 2.0 and later chips
(AR9285, AR9287, etc.)
- instead of calling iwn_plcp_signal() for every frame, map the expected
value directly within wn->ridx
- concat plcp, rflags and xrflags, there is no clean byte boundary within
the flags, for example the antenna setting uses bit 6, 7 and 8
- there is still need for a custom rate to plcp mapping, as those expected
by the hardware are not conform to the std
On legacy channels every once in a while the firmware throws a SYSASSERT
on line 208. On HT channels though this does always happen and I'm not
aware of any workaround currently.
