left-click event. It can be disabled setting the new
hw.usb.wsp.enable_single_tap_clicks sysctl to 0.
Submitted by: K Staring <qdk@quickdekay.net>
Pull Request: https://github.com/freebsd/freebsd/pull/97
Renumber cluase 4 to 3, per what everybody else did when BSD granted
them permission to remove clause 3. My insistance on keeping the same
numbering for legal reasons is too pedantic, so give up on that point.
Submitted by: Jan Schaumann <jschauma@stevens.edu>
Pull Request: https://github.com/freebsd/freebsd/pull/96
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
This change removes limitation of single S/G list entry and limitation on
maximal I/O size, using multiple data transfers per I/O if needed. Also
it removes code duplication between send and receive paths, which are now
completely equal.
for USB OTG-capable hardware to implement device side of USB
Mass Storage, ie pretend it's a flash drive. It's configured
in the same way as other CTL frontends, using ctladm(8)
or ctld(8). Differently from usfs(4), all the configuration
can be done without rebuilding the kernel.
Testing and review is welcome. Right now I'm still moving,
and I don't have access to my test environment, so I'm somewhat
reluctant to making larger changes to this code; on the other
hand I don't want to let it sit on Phab until my testing setup
is back, because I want to get it into 11.1-RELEASE.
Reviewed by: emaste (cursory), wblock (man page)
MFC after: 2 weeks
Relnotes: yes
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8787
This enables the PHY circuitry for UTMI+ level 2 and 3, and sets the
flag to tell the ehci code that the root hub has a transaction translator
in it. For imx6 we can use the standard ehci_get_port_speed_portsc()
function to find out what speed device is connected to the port.
The tty layer uses tsw_busy to poll for busy/idle status of the transmitter
hardware during close() and tcdrain(). The ucom layer defines ULSR_TXRDY and
ULSR_TSRE bits for the line status register; when both are set, the
transmitter is idle. Not all chip drivers maintain those bits in the sc_lsr
field, and if the bits never get set the transmitter will always appear
busy, causing hangs in tcdrain().
These changes add a new sc_flag bit, UCOM_FLAG_LSRTXIDLE. When this flag is
set, ucom_busy() uses the lsr bits to return busy vs. idle state, otherwise
it always returns idle (which is effectively what happened before this
change because tsw_busy wasn't implemented).
For the uftdi chip driver, these changes stop masking out the tx idle bits
when processing the status register (because now they're useful), and it
calls ucom_use_lsr_txbits() to indicate the bits are maintained by the
driver and can be used by ucom_busy().
Differential Revision: https://reviews.freebsd.org/D9183
sure the XHCI controller is reset after halting it. The problem is
clearly a BIOS bug as the suspend and resume is failing without
loading the XHCI driver. The same happens when using Linux and the
XHCI driver is not loaded.
Submitted by: Yanko Yankulov <yanko.yankulov@gmail.com>
PR: 216261
MFC after: 1 week
Replace archaic "busses" with modern form "buses."
Intentionally excluded:
* Old/random drivers I didn't recognize
* Old hardware in general
* Use of "busses" in code as identifiers
No functional change.
http://grammarist.com/spelling/buses-busses/
PR: 216099
Reported by: bltsrc at mail.ru
Sponsored by: Dell EMC Isilon
These have been tested back-to-back with Linux 3.x and a similar attachment
at the other end; a CDC EEM-like encapsulation can be used for emulated
Ethernet over udbp(4) with ng_ether.
I don't yet know which RX descriptor bits map to shortgi, long-gi,
short-preamble, long-preamble, STBC, LDPC, HT40, etc - so I can't
easily add those just yet.
There's apparently no per-frame RX RSSI information exposed so we
also just use the results from the previous calibration task.
This also tidies up how the per-mbuf RSSI is pushed into the frame -
now that it's attached to the mbuf via rx_stats, we don't have to
do any silly hijinx to get it out of the frame processing path.
Tested:
* RTL8712, 1x1 cut 3, STA mode
boot panics in conjunction with the recently added EARLY_AP_STARTUP feature.
The panics happen due to using kernel facilities like callouts too early.
Tested by: jhb @
MFC after: 1 week
- Do not ignore initialization errors; call ieee80211_stop()
when initialization failed.
- Use usb_pause_mtx() instead of DELAY() while waiting for firmware
loading; this fixes system freeze during firmware startup.
- Do not execute rsu_stop() when device is powered off; fixes
'unknown board type (rfconfig=0xff)' error when the device is
reattached.
Tested with Asus USB-N10.
- Replace all remaining DPRINTF(N)'s with RSU_DPRINTF.
- Add new RSU_DEBUG_USB flag to track error codes returned by
usbd_do_request_flags().
- Improve few messages.
- Add partial promiscuous mode support (no management frames;
they cannot be received by the firmware and net80211 at the same time).
- Add monitor mode support (all frames).
Tested with Asus, USB-N10.
This is required for USB Rx aggregation
(and fixes 'could not allocate RX mbuf' / few other failures).
While here, reduce the number of Rx buffers from 100 to 1 -
the driver never uses more than one Rx buffer.
Tested with Asus USB-N10.
values. This more closely matches other wifi drivers in the tree.
The bitmap levels have been based closely on other drivers (primarily
[u]rtwn(4)) in the hope that one day these can be unified into a shared
wifi-debug framework.
This is the first step of several pieces of work I'm planning on doing
with the run(4) driver. I may well adjust and refine some of the debug
bitmaps at a later date.
Reviewed by: adrian, avos
Differential Revision: https://reviews.freebsd.org/D8704
This change includes firmware commands for key setup +
some additional checking via CAMREAD / CAMWRITE registers.
Nothing (except rsu_delete_key() for pairwise keys) is deferred;
to ensure that things are done in order rsu_set_key() will wait
until key deletion task will be finished.
Tested with Asus USB-N10 (all ciphers).
Differences from initial (reviewed) patch:
- Pause AC queues before disassociation - since CMD_DISCONNECT clears
crypto state all pending frames must be processed / dropped before it.
- Check sc_running flag before trying to set static keys.
- Clear key index from bitmap even when firmware command fails
(it will be invalidated via CAMWRITE anyway).
Reviewed by: adrian, kevlo
Tested by: kevlo
Differential Revision: https://reviews.freebsd.org/D8706
- Append RCR_APP_PHYSTS bit after firmware loading - otherwise
firmware will reset the register and this modification will be lost.
(without it Rx PHY descriptor section will contain garbage).
- Check if R92S_RXDW0_PHYST bit is set (like it is done in rtwn(4)) -
even if infosz is non-zero the section may not contain anything useful.
- In case, if descriptor is absent (A-MPDU?) use last calibrated RSSI
(rtwn(4) uses RSSI from the previous (sub)frame; probably, this
approach should be used here too).
Tested with Asus USB-N10, STA mode.
- Fill in Rx radiotap header correctly (for every packet in a chain;
not once per chain).
- Fix rate / flags fields in Rx radiotap.
- Add debug messages for discarded frames.
- Pass received control (< sizeof(struct ieee80211_frame)) frames
to net80211 (if allowed by device filter; cannot happen yet).
Tested with Asus USB-N10.
Differential Revision: https://reviews.freebsd.org/D5723
- Set IEEE80211_FEXT_SCAN_OFFLOAD flag; firmware can send null data
frames when associated.
- Check IEEE80211_SCAN_ACTIVE scan flag instead of IEEE80211_F_ASCAN
ic flag; the last is never set since r170530.
- Eliminate software scan (net80211) <-> site_survey (driver) race:
* override ic_scan_curchan and ic_scan_mindwell pointers so net80211
will not try to finish scanning automatically;
* inform net80211 about current status via ieee80211_cancel_scan()
and ieee80211_scan_done();
* remove corresponding workaround from rsu_join_bss().
Now the driver can associate to an AP with hidden SSID.
Tested with Asus USB-N10.
