for i386 and alpha. Although it builds on sparc64, it does not yet work.
A similar hack as what is used on the sparc64 MD macros can be used to
make ia64 build too, but there doesn't seem to be much point.
mount_ifs: repocopy of sbin/mount, with most of the intelligence ripped out
and "ufs" replaced with "ifs" in the right places. It will only
mount a single filesystem, rather than the -t <type> magic that
our real mount does.
fsck_ifs: repocopy of sbin/fsck_ffs, but the directory structure stuff
(pass2 and some refcount checks) has been #ifdef'ed out.
src/sbin/Makefile: Build these two utilities
There is probably cruft code left in both which can be removed at a later
date, especially in mount_ifs, but I trust that people will not try
mount_ifs -a ..
Note: there are no man pages installed for these two commands as I haven't
actually written them yet.
Approved by: rwatson
Obtained from: NetbSD source tree
Second part of the fsck wrappers commit. This commit enables the new fsck
code (removing the fsck/* code and replacing it with the netbsd fsck
wrapper code), and enabling some FFS-based utilities to compile.
Details:
* quotacheck, fsdb required modification to use the fsck_ffs/ code rather
than fsck/ . This might change later since quotacheck requires preen.c
which should exist in fsck/ rather than fsck_ffs/
* src/Makefile has fsck_ffs added to it so it it built as part of the tree
now
* share/doc/smm/03.fsck/ uses the SMM.doc/ stuff from fsck_ffs, not fsck.
I've tested this, and it shouldn't require any changes on your machine.
The fsck wrapper reads /etc/fsck and is command-line-compatible enough
to not require rc changes (well, most changes unless you want to do
anything nifty by specifying the fs types explicityly, read the man page
if you want further details on what it can do.)
This now allows us to support multiple filesystem types during bootup.
Yes it is almost code freeze, but as the result of many thought, now I
think this should be added before 4.0...
make world check, kernel build check is done.
Reviewed by: green
Obtained from: KAME project
===================================
HARP | Host ATM Research Platform
===================================
HARP 3
What is this stuff?
-------------------
The Advanced Networking Group (ANG) at the Minnesota Supercomputer Center,
Inc. (MSCI), as part of its work on the MAGIC Gigabit Testbed, developed
the Host ATM Research Platform (HARP) software, which allows IP hosts to
communicate over ATM networks using standard protocols. It is intended to
be a high-quality platform for IP/ATM research.
HARP provides a way for IP hosts to connect to ATM networks. It supports
standard methods of communication using IP over ATM. A host's standard IP
software sends and receives datagrams via a HARP ATM interface. HARP provides
functionality similar to (and typically replaces) vendor-provided ATM device
driver software.
HARP includes full source code, making it possible for researchers to
experiment with different approaches to running IP over ATM. HARP is
self-contained; it requires no other licenses or commercial software packages.
HARP implements support for the IETF Classical IP model for using IP over ATM
networks, including:
o IETF ATMARP address resolution client
o IETF ATMARP address resolution server
o IETF SCSP/ATMARP server
o UNI 3.1 and 3.0 signalling protocols
o Fore Systems's SPANS signalling protocol
What's supported
----------------
The following are supported by HARP 3:
o ATM Host Interfaces
- FORE Systems, Inc. SBA-200 and SBA-200E ATM SBus Adapters
- FORE Systems, Inc. PCA-200E ATM PCI Adapters
- Efficient Networks, Inc. ENI-155p ATM PCI Adapters
o ATM Signalling Protocols
- The ATM Forum UNI 3.1 signalling protocol
- The ATM Forum UNI 3.0 signalling protocol
- The ATM Forum ILMI address registration
- FORE Systems's proprietary SPANS signalling protocol
- Permanent Virtual Channels (PVCs)
o IETF "Classical IP and ARP over ATM" model
- RFC 1483, "Multiprotocol Encapsulation over ATM Adaptation Layer 5"
- RFC 1577, "Classical IP and ARP over ATM"
- RFC 1626, "Default IP MTU for use over ATM AAL5"
- RFC 1755, "ATM Signaling Support for IP over ATM"
- RFC 2225, "Classical IP and ARP over ATM"
- RFC 2334, "Server Cache Synchronization Protocol (SCSP)"
- Internet Draft draft-ietf-ion-scsp-atmarp-00.txt,
"A Distributed ATMARP Service Using SCSP"
o ATM Sockets interface
- The file atm-sockets.txt contains further information
What's not supported
--------------------
The following major features of the above list are not currently supported:
o UNI point-to-multipoint support
o Driver support for Traffic Control/Quality of Service
o SPANS multicast and MPP support
o SPANS signalling using Efficient adapters
This software was developed under the sponsorship of the Defense Advanced
Research Projects Agency (DARPA).
Reviewed (lightly) by: phk
Submitted by: Network Computing Services, Inc.
