Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
The code for suspend/resume is derived from APM device driver.
Some people suggested the original code is somewhat buggy, but I'd
like to just move it from apm.c without any major changes for the
initial version. This code should be refined later.
To use pmtimer to adjust time at resume time, add
device pmtimer
in your kernel config file, and add
hint.pmtimer.0.at="isa"
in your device.hints
Reviewed by: -current, bde
from many folk.
o The reseed process is now a kthread. With SMPng, kthreads are
pre-emptive, so the annoying jerkiness of the mouse is gone.
o The data structures are protected by mutexes now, not splfoo()/splx().
o The cryptographic routines are broken out into their own subroutines.
this facilitates review, and possible replacement if that is ever
found necessary.
Thanks to: kris, green, peter, jasone, grog, jhb
Forgotten to thank: You know who you are; no offense intended.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
to recycle inodes after a destroy_dev() but not until all mounts
have picked up the change.
Add support for an overflow table for DEVFS inodes. The static
table defaults to 1024 inodes, if that fills, an overflow table
of 32k inodes is allocated. Both numbers can be changed at
compile time, the size of the overflow table also with the
sysctl vfs.devfs.noverflow.
Use atomic instructions to barrier between make_dev()/destroy_dev()
and the mounts.
Add lockmgr() locking of directories for operations accessing or
modifying the directory TAILQs.
Various nitpicking here and there.
This provides support for the Adaptec SCSI RAID controller family,
as well as the DPT SmartRAID V and VI families.
The driver will be maintained by Mark and Adaptec, and any changes
should be referred to the MAINTAINER.
the drivers.
* Remove legacy inx/outx support from chipset and replace with macros
which call busspace.
* Rework pci config accesses to route through the pcib device instead of
calling a MD function directly.
With these changes it is possible to cleanly support machines which have
more than one independantly numbered PCI busses. As a bonus, the new
busspace implementation should be measurably faster than the old one.
Remove old DEVFS support fields from dev_t.
Make uid, gid & mode members of dev_t and set them in make_dev().
Use correct uid, gid & mode in make_dev in disk minilayer.
Add support for registering alias names for a dev_t using the
new function make_dev_alias(). These will show up as symlinks
in DEVFS.
Use makedev() rather than make_dev() for MFSs magic devices to prevent
DEVFS from noticing this abuse.
Add a field for DEVFS inode number in dev_t.
Add new DEVFS in fs/devfs.
Add devfs cloning to:
disk minilayer (ie: ad(4), sd(4), cd(4) etc etc)
md(4), tun(4), bpf(4), fd(4)
If DEVFS add -d flag to /sbin/inits args to make it mount devfs.
Add commented out DEVFS to GENERIC
doesn't exist. This could bite you by allowing you merrily install your
modules one on top of the other as the regular file ${DESTDIR}/modules
and think it completed properly...
The tap driver is used to present a virtual Ethernet interface to the
system. Packets presented by the network stack to the interface are
made available to a character device in /dev. With tap and the bridge
code, you can make remote bridge configurations where both sides of
the bridge are separated by userland daemons.
This driver also has a special naming hack to allow it to serve a similar
purpose to the vmware port.
Submitted by: myevmenkin@att.com, vsilyaev@mindspring.com
associated patch to XFree86 allows the X server to work with this chipset
on FreeBSD. Additional work will include porting the Linux 3D driver.
Submitted by: Ruslan Ermilov <ru@FreeBSD.org>
the gating of system calls that cause modifications to the underlying
filesystem. The gating can be enabled by any filesystem that needs
to consistently suspend operations by adding the vop_stdgetwritemount
to their set of vnops. Once gating is enabled, the function
vfs_write_suspend stops all new write operations to a filesystem,
allows any filesystem modifying system calls already in progress
to complete, then sync's the filesystem to disk and returns. The
function vfs_write_resume allows the suspended write operations to
begin again. Gating is not added by default for all filesystems as
for SMP systems it adds two extra locks to such critical kernel
paths as the write system call. Thus, gating should only be added
as needed.
Details on the use and current status of snapshots in FFS can be
found in /sys/ufs/ffs/README.snapshot so for brevity and timelyness
is not included here. Unless and until you create a snapshot file,
these changes should have no effect on your system (famous last words).
(I had been busy for my own research activity until the last weekend)
Supported devices:
SB Midi Port (sbc + midi)
SB OPL3 (sbc + midi)
16550 UART (midi, needs a trick in your hint)
CS461x Midi Port (csa + midi)
OSS-compatible sequencer (seq)
Supported playing software:
playmidi (We definitely need more)
Notes:
/dev/midistat now reports installed midi drivers. /dev/sndstat reports
only pcm drivers. We need the new name(pcmstat?).
EMU8000(SB AWE) does not sound yet but does get probed so that the OPL3
synth on an AWE card works.
TODO:
MSS/PCI bridge drivers
Midi-tty interface to support general serial devices
Modules
Currently, many drivers support more than one bus of ISA, EISA, MCA,
PCI.
Before this commit, we had, for example, some SCSI devices listed more
than once, iirc, some up to three times (ISA/EISA, MCA, PCI).
Since now the "device" line is common for all of them and they only
differ for the hints stuff, I did the following:
First, list Busses: (E)ISA, MCA, PCI and explain, that only ISA
needs the hints stuff.
Move NIC/SCSI stuff, which were the only split sections, behind these
stuff. Describe all drivers only one time and list all supported
chips.
List all device (+ hints for ISA, if possible).
I've also added few additional supported chips to some drivers, xl for
example and some SCSI drivers.
Also, softupdates is no longer disabled by default, so the comment should
not say, it's not enabled by default due to license issues.
Approved by: asmodai
To come: include PAO devices (imp volunteered for help)
FreeBSD.org e-mail.
o Notice also that it's listed as "aud" not "audit" which will
probably change in the near future with updates to the auditing
implementation.
set equal to the number of kilobytes in your cache. The old options are
still supported for backwards compatibility.
Submitted by: Kelly Yancey <kbyanc@posi.net>
This means 'options NETGRAPH' is no longer necessary in order to get
netgraph-enabled Ethernet interfaces. This supports loading/unloading
the ng_ether.ko and attaching/detaching the Ethernet interface in any
order.
Add two new hooks 'upper' and 'lower' to allow access to the protocol
demux engine and the raw device, respectively. This enables bridging
to be defined as a netgraph node, if so desired.
Reviewed by: freebsd-net@freebsd.org
rest of the kernel. Added new option TDFX_LINUX for optional
LINUX_EMULATION, so that perhaps some people don't have to use linux emu to
run the driver if they don't want to.
