Some of FDT blobs for AM335x-based devices use pinmux pullup/pulldown
flag to setup initial GPIO ouputp value, e.g. 4DCAPE-43 sets LCD DATAEN
signal this way. It works for Linux because Linux driver does not enforce
pin direction until after it's requested by consumer. So input with pullup
flag set acts as output with GPIO_HIGH value
Reviewed by: loos
This is a clean-up patch from a serie delivering support for
Annapurna Labs Alpine PoC.
The HAL files have already been added to sys/contrib/alpine-hal
so there is no need for them in the platform directory.
This patch removes obsolete files.
Reviewed by: andrew
Obtained from: Semihalf
Sponsored by: Annapurna Labs
Differential Revision: https://reviews.freebsd.org/D3248
in lockstat.ko. This means that lockstat probes now have typed arguments and
will utilize SDT probe hot-patching support when it arrives.
Reviewed by: gnn
Differential Revision: https://reviews.freebsd.org/D2993
If KSTACK_PAGES was changed to anything alse than the default,
the value from param.h was taken instead in some places and
the value from KENRCONF in some others. This resulted in
inconsistency which caused corruption in SMP envorinment.
Ensure all places where KSTACK_PAGES are used the opt_kstack_pages.h
is included.
The file opt_kstack_pages.h could not be included in param.h
because was breaking the toolchain compilation.
Reviewed by: kib
Obtained from: Semihalf
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D3094
o Return the real hardware state in gpio_pin_getflags() instead of keep
the last state in an internal table. Now the driver returns the real
state of pins (input/output and pull-up/pull-down) at all times.
o Use a spin mutex. This is required by interrupts and the 1-wire code.
o Use better variable names and place parentheses around them in MACROS.
o Do not lock the driver when returning static data.
Tested with gpioled(4) and DS1820 (1-wire) sensors on banana pi.
provide a semantic defined by the C11 fences with corresponding
memory_order.
atomic_thread_fence_acq() gives r | r, w, where r and w are read and
write accesses, and | denotes the fence itself.
atomic_thread_fence_rel() is r, w | w.
atomic_thread_fence_acq_rel() is the combination of the acquire and
release in single operation. Note that reads after the acq+rel fence
could be made visible before writes preceeding the fence.
atomic_thread_fence_seq_cst() orders all accesses before/after the
fence, and the fence itself is globally ordered against other
sequentially consistent atomic operations.
Reviewed by: alc
Discussed with: bde
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
change to GMAC easier on A20 SoCs.
On A10 only the EMAC controller is available (fast ethernet), but on A20
there is also GMAC a high (or better) performant controller (gigabit
ethernet).
On A20 the both controllers uses the same pins to talk to the ethernet PHY
(MII or RGMII) and they can be selected by the GPIO pin mux.
There is work in progress to bring in GMAC support.
The Allwinner SoC has an AHCI device on its internal main bus rather
than the PCI bus. This SoC is somewhat underdocumented, and its SATA
controller is no exception. The methods to support this chip were
harvested from the Linux Allwinner SDK, and then constants invented to
describe what's going on based on low-level constants contained in the
SATA standard and guess work.
This SoC requires a specific AHCI channel setup in order to start the
operations on the channel properly.
Clock setup and AHCI channel setup idea came from NetBSD.
Tested on Cubieboard 2 and Banana pi (and attachment on Cubieboard by
Pratik Singhal).
Differential Revision: https://reviews.freebsd.org/D737
Submitted by: imp
Reviewed by: imp, ganbold, mav, andrew
DMA handles all data transfers up to 128K or 16 segments and fallback to
pio mode when DMA requirements are not met.
The read performance has improved greatly while the write performance also
showed some improvement but seems limited by the card type and quality.
Submitted by: Pratik Singhal <pratiksinghal@freebsd.org>
Sponsored by: Google Summer of Code 2015
Tested on: A10 (cubieboard) and A20 (cubieboard 2 and banana pi)
- Add driver for TDA19988 HDMI framer
- Add simple interface to communicate with HDMI sink: read EDID and set videomode
- Add event-based API to notify LCD controller when HDMI sink is available
- Add HDMI framer node and add refernce to it to lcdc node. This part of
DTS tree is custom and does not match Linux DTS because Linux uses
combination of pseudo-node in DTS and hardcoded driver information
that does not map to our model.
consumers can configure clock frequency
- Add ti_prcm_clk_set_source_freq wrapper for clk_set_source_freq
- Add am335x_clk_set_arm_disp_freq function to control pixel clock
frequency for LCD and HDMI output. Both of them are sensitive
to frequency skews and we need to get pixel clock matching requested
frequency as close to possible
drivers, one for fdt, one for acpi. It then uses this to decide if it will
use fdt or acpi.
The GICv2 (interrupt controller) and Generic Timer drivers have been
updated to handle both cases.
As this is early code we still need FDT to find the kernel console, and
some parts are still missing, including PCI support.
Differential Revision: https://reviews.freebsd.org/D2463
Reviewed by: jhb, jkim, emaste
Obtained from: ABT Systems Ltd
Relnotes: Yes
Sponsored by: The FreeBSD Foundation
This will require for AArch64 as we dont have modules yet.
Sponsored by: HEIF5
Sponsored by: ARM Ltd.
Differential Revision: https://reviews.freebsd.org/D1997
Thread credentials are maintained as follows: each thread has a pointer to
creds and a reference on them. The pointer is compared with proc's creds on
userspace<->kernel boundary and updated if needed.
This patch introduces a counter which can be compared instead, so that more
structures can use this scheme without adding more comparisons on the boundary.
charger configuration and provide some basic control knobs to
set charger voltage and dump config on boot. Two loader tunables
have been added:
o hw.am335x_pmic.bootverbose set to 1 to get more info on the
boot;
o hw.am335x_pmic.vo: set to charger voltage to be applied on
kernel initialization time, supported values are "4.10V",
"4.15V", "4.20V" and "4.25V".
Cleanup code a bit in general, move TPS65217 register
definitions into a separate header, convert bit-banging
defines into bitmap structures.
Also threat the case when power source is neither "AC" nor "USB"
as "Battery", not "Unknown".
On armv6, cache maintenance can trigger page faults. Add handling so that
these turn into SIGSEGV that kills the process rather than panics that kill
the kernel.
Differential Revision: https://reviews.freebsd.org/D2035
Submitted by: Michal Meloun <meloun@miracle.cz>
