the corresponding manpage has been committed.
The rest of "vlan" words, which are refering
to the technology itself, should be capitalized.
MFC after: 1 week
reorganize the printing of the interface name when using wildcard
cloning so it is not printed if it we either immediately rename or
destroy the interface.
Reviewed by: ru
Setting this flag on an ethernet interface blocks transmission of packets
and discards incoming packets after BPF processing.
This is useful if you want to monitor network trafic but not interact
with the network in question.
Sponsored by: http://www.babeltech.dk
Also, for all interfaces in this mode pass all ethernet frames to upper layer,
even those not addressed to our own MAC, which allows packets encapsulated
in those frames be processed with packet filters (ipfw(8) et al).
Emphatically requested by: Anton Turygin <pa3op@ukr-link.net>
Valuable suggestions by: fenner
that could be used to set/get arbitrary length link level
addresses. Alias "lladdr" parameter and "ether" family
to the new "link" family for backward compatibility.
PR: bin/31476
MFC after: 1 week
The first "synopsis" example has a "[/prefixlength]" which shouldn't
be there, since that stuff is part of the preceeding "address" as is
explained in the description of "address".
(The way it is now, 192.168.0.1/16/prefixlength would be a proper
operand. Note that "prefixlength" is not mentioned by name anywhere.)
PR: 32462
Submitted by: Gary W. Swearingen <swear@blarg.net>
This work was based on kame-20010528-freebsd43-snap.tgz and some
critical problem after the snap was out were fixed.
There are many many changes since last KAME merge.
TODO:
- The definitions of SADB_* in sys/net/pfkeyv2.h are still different
from RFC2407/IANA assignment because of binary compatibility
issue. It should be fixed under 5-CURRENT.
- ip6po_m member of struct ip6_pktopts is no longer used. But, it
is still there because of binary compatibility issue. It should
be removed under 5-CURRENT.
Reviewed by: itojun
Obtained from: KAME
MFC after: 3 weeks
printed on a single, very long, and generally unreadable line. This
isn't very useful. It's also really ugly and most of the time you don't
care what media is supported anyway.
PR: 27701
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
despite the fact that most people want to set exactly the same settings
regardless of which card they have. It has been repeatidly suggested
that this configuration should be done via ifconfig. This patch
implements the required functionality in ifconfig and add support to the
wi and an drivers. It also provides partial, untested support for the
awi driver.
PR: 25577
Submitted by: Brooks Davis <brooks@one-eyed-alien.net>
address on an interface. This basically allows you to do what my
little setmac module/utility does via ifconfig. This involves the
following changes:
socket.h: define SIOCSIFLLADDR
if.c: add support for SIOCSIFLLADDR, which resets the values in
the arpcom struct and sockaddr_dl for the specified interface.
Note that if the interface is already up, we need to down/up
it in order to program the underlying hardware's receive filter.
ifconfig.c: add lladdr command
ifconfig.8: document lladdr command
You can now force the MAC address on any ethernet interface to be
whatever you want. (The change is not sticky across reboots of course:
we don't actually reprogram the EEPROM or anything.) Actually, you
can reprogram the MAC address on other kinds of interfaces too; this
shouldn't be ethernet-specific (though at the moment it's limited to
6 bytes of address data).
Nobody ran up to me and said "this is the politically correct way to
do this!" so I don't want to hear any complaints from people who think
I could have done it more elegantly. Consider yourselves lucky I didn't
do it by having ifconfig tread all over /dev/kmem.
