device. The details include the current value of the BAR (including all
the flag bits and the current base address), its length, and whether or not
it is enabled. Since this operation is not invasive, non-root users are
allowed to use it (unlike manual config register access which requires
root). The intention is that userland apps (such as Xorg) will use this
interface rather than dangerously frobbing the BARs from userland to
obtain this information.
- Add a new sub-mode to the 'list' mode of pciconf. The -b flag when used
with -l will now list all the active BARs for each device.
MFC after: 1 month
src/usr.bin/usbhidctl/usbhid.c
src/sys/dev/usb2/include/usb2_hid.h
src/sys/dev/usb2/input/uhid2.c
src/lib/libusbhid/Makefile
src/lib/libusbhid/descr.c
src/lib/libusbhid/descr_compat.c
src/lib/libusbhid/usbhid.3
src/lib/libusbhid/usbhid.h
src/lib/libusbhid/usbvar.h
Patches to make libusbhid and HID userland utilities compatible with
the new USB stack. All HID ioctls should go through the libusbhid
library to ensure compatibility. I have found at least one piece of
software in /usr/ports which needs to get updated before USB HID
devices will work. This is the X joystick input driver.
Reported and tested by:
Daichi GOTO and Masanori OZAWA.
src/sys/dev/usb2/core/usb2_process.c
Correct USB process names.
Reported by:
Andre Guibert de Bruet
src/sys/dev/usb2/serial/uftdi2.c
Integrate changes from old USB stack.
Submitted by: hps
Move the interupt handler to a driver_intr_t type function as it was trying
to do way to much for a lightweight filter interrupt function.
Introduce much more locking around fc->mtx. Tested this for lock reversals
and other such lockups. Locking seems to be working better, but there
is much more to do with regard to locking. The most significant lock is
in the BUS RESET handler. It was possible, before this checkin, to set
a bus reset via "fwcontrol -r" and have the BUS RESET handler fire before
the code responsible for asserting BUS RESET was complete. This locking
fixes that issue.
Move some of the memory allocations in the fc struct to the attach function
in firewire.c
Rework the businfo.generation indicator to be merely a on/off bit now.
It's purpose according to spec is to notify the bus that the config ROM
has changed. That's it.
Catch and squash a possible panic in SBP where in the SBP_LOCK was held
during a possible error case. The error handling code would definitely
panic as it would try to acquire the SBP_LOCK on entrance.
Catch and squash a camcontrol/device lockup when firewire drives go away.
When a firewire device was powered off or disconnected from the firewire
bus, a "camcontrol rescan all" would hang trying to poll removed devices
as they were not properly detached. Don't do that.
Approved by: scottl
MFC after: 2 weeks
o remove HAL_CHANNEL; convert the hal to use net80211 channels; this
mostly involves mechanical changes to variable names and channel
attribute macros
o gut HAL_CHANNEL_PRIVATE as most of the contents are now redundant
with the net80211 channel available
o change api for ath_hal_init_channels: no more reglass id's, no more outdoor
indication (was a noop), anM contents
o add ath_hal_getchannels to have the hal construct a channel list without
altering runtime state; this is used to retrieve the calibration list for
the device in ath_getradiocaps
o add ath_hal_set_channels to take a channel list and regulatory data from
above and construct internal state to match (maps frequencies for 900MHz
cards, setup for CTL lookups, etc)
o compact the private channel table: we keep one private channel
per frequency instead of one per HAL_CHANNEL; this gives a big
space savings and potentially improves ani and calibration by
sharing state (to be seen; didn't see anything in testing); a new config
option AH_MAXCHAN controls the table size (default to 96 which
was chosen to be ~3x the largest expected size)
o shrink ani state and change to mirror private channel table (one entry per
frequency indexed by ic_devdata)
o move ani state flags to private channel state
o remove country codes; use net80211 definitions instead
o remove GSM regulatory support; it's no longer needed now that we
pass in channel lists from above
o consolidate ADHOC_NO_11A attribute with DISALLOW_ADHOC_11A
o simplify initial channel list construction based on the EEPROM contents;
we preserve country code support for now but may want to just fallback
to a WWR sku and dispatch the discovered country code up to user space
so the channel list can be constructed using the master regdomain tables
o defer to net80211 for max antenna gain
o eliminate sorting of internal channel table; now that we use ic_devdata
as an index, table lookups are O(1)
o remove internal copy of the country code; the public one is sufficient
o remove AH_SUPPORT_11D conditional compilation; we always support 11d
o remove ath_hal_ispublicsafetysku; not needed any more
o remove ath_hal_isgsmsku; no more GSM stuff
o move Conformance Test Limit (CTL) state from private channel to a lookup
using per-band pointers cached in the private state block
o remove regulatory class id support; was unused and belongs in net80211
o fix channel list construction to set IEEE80211_CHAN_NOADHOC,
IEEE80211_CHAN_NOHOSTAP, and IEEE80211_CHAN_4MSXMIT
o remove private channel flags CHANNEL_DFS and CHANNEL_4MS_LIMIT; these are
now set in the constructed net80211 channel
o store CHANNEL_NFCREQUIRED (Noise Floor Required) channel attribute in one
of the driver-private flag bits of the net80211 channel
o move 900MHz frequency mapping into the hal; the mapped frequency is stored
in the private channel and used throughout the hal (no more mapping in the
driver and/or net80211)
o remove ath_hal_mhz2ieee; it's no longer needed as net80211 does the
calculation and available in the net80211 channel
o change noise floor calibration logic to work with compacted private channel
table setup; this may require revisiting as we no longer can distinguish
channel attributes (e.g. 11b vs 11g vs turbo) but since the data is used
only to calculate status data we can live with it for now
o change ah_getChipPowerLimits internal method to operate on a single channel
instead of all channels in the private channel table
o add ath_hal_gethwchannel to map a net80211 channel to a h/w frequency
(always the same except for 900MHz channels)
o add HAL_EEBADREG and HAL_EEBADCC status codes to better identify regulatory
problems
o remove CTRY_DEBUG and CTRY_DEFAULT enum's; these come from net80211 now
o change ath_hal_getwirelessmodes to really return wireless modes supported
by the hardware (was previously applying regulatory constraints)
o return channel interference status with IEEE80211_CHANSTATE_CWINT (should
change to a callback so hal api's can take const pointers)
o remove some #define's no longer needed with the inclusion of
<net80211/_ieee80211.h>
Sponsored by: Carlson Wireless
Inside the kernel, the minor() function was responsible for obtaining
the device minor number of a character device. Because we made device
numbers dynamically allocated and independent of the unit number passed
to make_dev() a long time ago, it was actually a misnomer. If you really
want to obtain the device number, you should use dev2udev().
We already converted all the drivers to use dev2unit() to obtain the
device unit number, which is still used by a lot of drivers. I've
noticed not a single driver passes NULL to dev2unit(). Even if they
would, its behaviour would make little sense. This is why I've removed
the NULL check.
Ths commit removes minor(), minor2unit() and unit2minor() from the
kernel. Because there was a naming collision with uminor(), we can
rename umajor() and uminor() back to major() and minor(). This means
that the makedev(3) manual page also applies to kernel space code now.
I suspect umajor() and uminor() isn't used that often in external code,
but to make it easier for other parties to port their code, I've
increased __FreeBSD_version to 800062.
exceeded the maximum size of 1 page for OHCI controllers. Other serial
drivers use the same size, so I assume this should be enough (1MB/s
throughput?).
Make detach() completely synchronous. Properly handle stalled USB
transfers (use internal mechanism instead of submitting own control
transfers). Rename/remove a couple of variables and update comments.
This work was done in close collaboration with HPS.
Reviewed by: HPS
- To avoid having a bunch of locks that end up always getting acquired as
a group, give each ppc(4) device a mutex which it shares with all the
child devices including ppbus(4), lpt(4), plip(4), etc. This mutex
is then used for all the locking.
- Rework the interrupt handling stuff yet again. Now ppbus drivers setup
their interrupt handler during attach and tear it down during detach
like most other drivers. ppbus(4) only invokes the interrupt handler
of the device that currently owns the bus (if any) when an interrupt
occurs, however. Also, interrupt handlers in general now accept their
softc pointers as their argument rather than the device_t. Another
feature of the ppbus interrupt handlers is that they are called with
the parent ppc device's lock already held. This minimizes the number
of lock operations during an interrupt.
- Mark plip(4), lpt(4), pcfclock(4), ppi(4), vpo(4) MPSAFE.
- lpbb(4) uses the ppc lock instead of Giant.
- Other plip(4) changes:
- Add a mutex to protect the global tables in plip(4) and free them on
module unload.
- Add a detach routine.
- Split out the init/stop code from the ioctl routine into separate
functions.
- Other lpt(4) changes:
- Use device_printf().
- Use a dedicated callout for the lptout timer.
- Allocate the I/O buffers at attach and detach rather than during
open and close as this simplifies the locking at the cost of
1024+32 bytes when the driver is attached.
- Other ppi(4) changes:
- Use an sx lock to serialize open and close.
- Remove unused HADBUS flag.
- Add a detach routine.
- Use a malloc'd buffer for each read and write to avoid races with
concurrent read/write.
- Other pps(4) changes:
- Use a callout rather than a callout handle with timeout().
- Conform to the new ppbus requirements (regular mutex, non-filter
interrupt handler). pps(4) is probably going to have to become a
standalone driver that doesn't use ppbus(4) to satisfy it's
requirements for low latency as a result.
- Use an sx lock to serialize open and close.
- Other vpo(4) changes:
- Use the parent ppc device's lock to create the CAM sim instead of
Giant.
- Other ppc(4) changes:
- Fix ppc_isa's detach method to detach instead of calling attach.
Tested by: no one :-(
Some time ago I tried adding Unicode rendering to the teken demo
application, but I didn't get it working. It seems I forgot to call
setlocale(). Polish this code and make sure it doesn't get lost.
Also a small fix for my previous commit: all Unicode characters in
teken_boxdrawing are below 0x10000, so store them as 16-bit values.
