Commit Graph

162 Commits

Author SHA1 Message Date
jhb
f8c0225fe0 Do not require a filter-only interrupt handler for puc ports that are not
serial devices (such as printer ports).  This allows ppc devices attached
to puc to correctly setup an interrupt handler and work.

Tested by:	Andre Albsmeier  Andre.Albsmeier@siemens.com
MFC after:	1 week
2013-01-15 20:13:25 +00:00
eadler
04e7b32045 Add support for Advantech PCI-1602 RS-485/RS-422 serial card
PR:		kern/169726
Submitted by:	Jan Mikkelsen <janm@transactionware.com>
Approved by:	cperciva (implicit)
MFC after:	5 days
2012-11-09 01:51:06 +00:00
eadler
ec8c8f8e30 Add support for SIIG Cyber Serial Dual PCI 16C850
Submitted by:	David Boyd David.Boyd@insightbb.com
Approved by:	cperciva
MFC after:	3 days
2012-08-05 19:37:18 +00:00
eadler
58d5fe0bdc Add additional Perle Speed LE serial cards
PR:		kern/168816
Submitted by:	Dennis Oyama <doyama@perle.com>
Approved by:	cperciva
MFC after:	1 week
2012-08-05 08:10:02 +00:00
fjoe
e4171792ab - Change back "d_ofs" to int8_t to not pessimize padding and size of "struct puc_cfg".
- Use "puc_config_moxa" for Moxa boards that need d_ofs greater than 0x7f

Prodded by:	marcel@, gavin@
MFC after:	3 days
2012-07-31 05:23:23 +00:00
fjoe
2a52af28e6 Remove Moxa CP-132EL definition (RS422/485-only board). 2012-06-21 04:57:59 +00:00
fjoe
490b3d9fc0 Add support for the following Moxa PCIe multiport serial boards:
- CP102E
- CP102EL
- CP132EL
- CP114EL
- CP118EL-A
- CP168EL-A

MFC after:	1 week
2012-06-21 03:10:48 +00:00
jhay
8ab1626704 Add support for the Sunix SER5437A dual serial PCI Express card. 2012-06-08 06:07:23 +00:00
eadler
caff493a8e Add support for Sun 1040 PCI Quad Serial
PR:		kern/163450
Submitted by:	Anonymous Hardware Hacker <silicium@harmony-p.ath.cx>
Approved by:	cperciva
MFC after:	1 week
2012-05-30 03:47:51 +00:00
marius
17e14c6132 - There's no need to overwrite the default device method with the default
one. Interestingly, these are actually the default for quite some time
  (bus_generic_driver_added(9) since r52045 and bus_generic_print_child(9)
  since r52045) but even recently added device drivers do this unnecessarily.
  Discussed with: jhb, marcel
- While at it, use DEVMETHOD_END.
  Discussed with: jhb
- Also while at it, use __FBSDID.
2011-11-22 21:28:20 +00:00
eadler
7b4ac9ae27 - add support for Titan VScom PCIex-800H
PR:		kern/124128
Submitted by:	Maxim Frolov <maxim.frolov.07@gmail.com> (original)
Approved by:	jhb
MFC after:	1 week
2011-11-15 17:53:29 +00:00
eadler
38110cede2 - add support for CP-104EL-A and CP-104JU to puc
PR:		151365
Submitted by:	Joerg Niendorf <f5d10a@internode.on.net>
Approved by:	jhb
2011-11-11 22:24:16 +00:00
ed
e97eae1577 Mark MALLOC_DEFINEs static that have no corresponding MALLOC_DECLAREs.
This means that their use is restricted to a single C file.
2011-11-07 06:44:47 +00:00
eadler
f22435ed56 - add support for I-O DATA RSA-PCI2/R
PR:		kern/142999
Submitted by:	Takefu Kenji <takefu@airport.fm>
Approved by:	jhb
Approved by:	sahil (mentor)
MFC after:	1 week
2011-10-15 21:06:08 +00:00
ae
8118992bd0 Add Oxford Semiconductor OXPCIe952 (0x1c38) 1 port serial card.
PR:		kern/160895
Submitted by:	Konstantin V. Krotov
MFC after:	1 week
2011-09-29 15:43:02 +00:00
jhb
e2a937e93d Add device id for the Moxa CP-112UL dual-port serial adapters.
Submitted by:	Jan Mikkelsen  janm of transactionware com
Approved by:	re (kib)
MFC after:	1 week
2011-08-15 19:29:25 +00:00
jhb
a11bba2ac0 Add location and pnpinfo strings for puc device ports. The location is
announced during boot and contains the port number.  The pnpinfo string
lists the port type (PUC_TYPE_* constants).

Tested by:	Boris Samorodov  bsam ipt ru
MFC after:	1 week
2011-06-14 18:19:48 +00:00
jhb
d046e38f5f Some style fixes.
Submitted by:	bde
2011-06-06 15:33:15 +00:00
jhb
1075137ca9 - Rename the Cronyx Omega2-PCI entry to Exar XR17C158 since that is the
real owner of the device ID.  Also rename the associated config
  function while here.
- Add support for the 2-port and 4-port Exar parts as well: Exar XR17C/D152
  and Exar XR17C154.

Tested by:	Mike Tancsa, Willy Offermans  Willy of offermans rompen nl
MFC after:	1 week
2011-06-03 20:59:21 +00:00
jhb
a10f288d7e For Timedia multiport serial adapters, the first two ports use a SUN1889
which uses a non-standard clock (* 8) while any additional ports use
SUN1699 chips which use a standard clock.

Tested by:	N.J. Mann   njm of njm me uk
MFC after:	1 week
2011-05-26 20:54:45 +00:00
jhb
76caf7ac52 Add support for the SIIG Cyber 2S PCIe adapter. It is based on an
Oxford Semiconductor OX16PCI954 but uses only two ports with a non-default
clock rate.

PR:		kern/152034
Tested by:	Hans Fiedler  hans of hermes louisville edu
MFC after:	1 week
2011-05-19 11:41:12 +00:00
jhb
6491e2a571 Add an entry for the SIIG Quartet Serial 850 which uses an Oxford
chip with a non-default clock.

PR:		kern/147583
MFC after:	1 week
2011-05-10 12:40:35 +00:00
jhb
6c7b490838 Add an entry for the Kuroutoshikou SERIAL4P-LPPCI2 which uses an Oxford
4 port chip but with a nonstandard clock.

PR:		kern/104212
Submitted by:	Shuichi KITAGUCHI  kit of ysnb net
MFC after:	1 week
2011-05-02 14:34:03 +00:00
jhb
c7e5cfecda Add support for Oxford PCI Express Expresso family devices.
For these devices, the number of supported ports is read from a register
in BAR 0.

PR:		kern/134878
Submitted by:	David Wood  david of wood2 org uk
MFC after:	1 week
2011-04-28 19:19:25 +00:00
emaste
459e9639c3 Add Exar octal PCI UART.
Submitted by:	Mark Johnston
Obtained from:	Sandvine Incorporated
2010-12-18 02:54:51 +00:00
jhb
547182687c Add support for the Perle Speed4 LE.
Submitted by:	Douglas K. Rand  rand of meridian-enviro com
MFC after:	3 days
2010-05-20 13:16:42 +00:00
marcel
2e6099f494 Fix interrupt handling. It started off broken and grew worse over time.
The rewrite of the interrupt handler includes:
o   loop until all pending interrupts are handled. This closes a
    race condition.
o   count the number of interrupt sources we handled so that we can
    properly return FILTER_HANDLED or FILTER_STRAY when we break out
    of the loop.
o   When matching the interrupt source to the devices that have that
    source pending, check only from the set of devices we found to
    have a pending interrupt.

PR:		kern/140947
MFC after:	3 days
2009-12-11 03:08:07 +00:00
marcel
c61e7af92e Add support for the NetMos NM9865 family of Serial/Parallel ports.
Obtained from:	NetMos MCS9865 v1.0.0.1 driver
MFC after:	3 days
2009-12-07 20:05:02 +00:00
np
5bbf1e2151 Make puc(4) aware of this 2 port serial card based on NetMos 9835:
puc0@pci0:4:1:0:       class=0x070002 card=0x00021000 chip=0x98359710 rev=0x01 hdr=0x00

Reviewed by:	marcel@
Approved by:	gnn (mentor)
2009-06-20 00:04:48 +00:00
rwatson
d6cef153cd Add support for the four PUC serial interfaces found on IBM SurePOS 300
series POS terminals.

MFC after:	3 days
Submitted by:	Marc Balmer <marc at msys.ch>
2009-06-02 09:58:17 +00:00
imp
7cf1a35509 remove now-redunant cardbus attachment lines. 2009-03-09 13:25:34 +00:00
jhb
dc03a05b16 Add support for the single-port NetMos NM9835 serial adapter. The puc(4)
entry is a specific entry to override the generic NetMos entry so that
puc(4) will leave this device alone and let uart(4) claim it.

Submitted by:	Navdeep Parhar  nparhar @ gmail
Reviewed by:	marcel
MFC after:	1 week
2009-03-05 16:43:33 +00:00
kevlo
b600a85653 Add support for the Sunix SUN1889-based dual parallel port card.
PR: kern/128219
Submitted by: Thinker K.F. Li <thinker at branda dot to>
2009-02-12 10:39:19 +00:00
stas
5b66cc0d53 - Add support for Moxa Technologies CP-168EL/PCIe card.
Submitted by:	dmarck
MFC after:	1 week
2009-01-27 09:38:44 +00:00
rik
042c879619 Add support for the Oxford OX16PCI958-based card.
Note, that the patch provided with this card for the Linux states that
the card uses DEFAULT_RCLK * 2, while in fact it is '* 10'.  So probably
we should also use the subdevice/subvendord here. For now just ignore
that fact.

PR:		kern/129665
Submitted by:	bsam
Obtained from:	united efforst with bsam
2008-12-27 15:22:22 +00:00
des
47259920d5 Add an entry for the "SIIG Cyber 4 PCI 16550", which is a four-port card
based on the OX16PCI954 chip with a non-standard clock.

MFC after:	3 days
2008-10-25 10:55:49 +00:00
des
b0c31e1c93 Revert r179409; it breaks all OX16PCI954-based cards except the SIIG 4.
MFC after:	3 days
2008-10-13 12:28:33 +00:00
thompsa
87939ee394 Add the Decision Computer Inc, PCCOM 8-port serial card.
PR:		kern/69730
Submitted by:	Darrin Smith
2008-08-22 00:13:17 +00:00
thompsa
9bc6bc58a2 Add the VScom PCI-100L card.
PR:		kern/72352
Submitted by:	Thomas Nystrom
2008-08-22 00:12:08 +00:00
thompsa
a6ffa54b6f Add the Avlab Technology PCI IO 4S-850 4 port serial card.
PR:		kern/110797
Submitted by:	Trevor Roydhouse
2008-08-21 23:22:32 +00:00
mckusick
2ef107420e The SIIG 4 port serial card based on the Oxford OX16PCI954 is
clocked at 10x normal speed. That is, when you set it for 9600
baud, it actually does 96000 baud. In order to make it plug and
play with other serial ports, it has to have its clock rate
reduced by a factor of 10.

Discussed with: Marcel Moolenaar
MFC after:	2 weeks
2008-05-29 07:15:52 +00:00
marcel
0e99128934 Fix RID calculation. The RID is really the BAR for PCI cards,
so the index needs to be translated into an offset. While we
did add the offset (0x10), we forgot to account for the width.

Tested by: Thomas Vogt
MFC after: 3 days
2008-05-16 14:57:48 +00:00
maxim
455ab3c71b o Add Moxa Technologies CP-104EL PCI Express 4 port Serial card.
PR:		kern/119515
Submitted by:	Gavin Stone-Tolcher
MFC after:	1 month
2008-01-12 19:14:29 +00:00
des
62062f6473 Rewrite puc_pci_match() to handle non-trivial cases correctly.
MFC after:	1 week
2007-10-13 12:14:20 +00:00
peter
33fc7010cd Calculate the correct PCI BAR for the Timedia based serial cards. The
Linux equivalent gives BAR offsets relative to the implied base of 0x10.
Our PUC_CFG_GET_RID functions have to add the base offset themselves.
2007-06-07 06:28:48 +00:00
piso
a500547688 -axe p_ih from struct puc_port cause it was useless
-correctly check for filter only handler

Reviewed by: marcel
Tested by: marcel
2007-06-06 22:17:01 +00:00
piso
6a2ffa86e5 o break newbus api: add a new argument of type driver_filter_t to
bus_setup_intr()

o add an int return code to all fast handlers

o retire INTR_FAST/IH_FAST

For more info: http://docs.freebsd.org/cgi/getmsg.cgi?fetch=465712+0+current/freebsd-current

Reviewed by: many
Approved by: re@
2007-02-23 12:19:07 +00:00
marcel
b288558c95 Add SIIG 4 port serial card based on the Oxford OX16PCI954. 2006-09-04 18:27:14 +00:00
obrien
e8d45535f3 Fix building with GCC 4.2: ensure types are defined before refering to them. 2006-06-29 16:27:19 +00:00
imp
6e19662308 Need machine/bus.h here too 2006-06-12 19:22:44 +00:00