allow the child atkbd device to reuse that IRQ resource instead of
reallocating the same IRQ from the parent bus inside the atkbd driver.
- Don't allocate a shared IRQ for the atkbd driver. For AT keyboard
devices on an ISA bus the IRQ is not shareable. Instead, the bus driver
should mark the IRQ shareable if the bus supports shared IRQs.
- Don't identify child devices until after the atkbdc device itself has
attached.
This reflects actual type used to store and compare child device orders.
Change is mostly done via a Coccinelle (soon to be devel/coccinelle)
semantic patch.
Verified by LINT+modules kernel builds.
Followup to: r212213
MFC after: 10 days
emulated by BIOS using SMI interrupt. On those chipsets reading
from the status port may be thousand times slower than usually.
Sometimes this emilation is not working properly resulting in
commands timing out and since we assume that inb() operation
takes very little time to complete we need to adjust number of
retries to keep waiting time within a designed limits (100ms).
Measure time it takes to make read_status() call and adjust
number of retries accordingly.
To keep it simple, use TSC to measure inb() performance and
keep it to amd64-only, since TSC may not available on older
CPUs.
Also enable detection of the AT controller absence on amd64.
Reviewed by: jhb
MFC after: 1 month
controller as we use in boot blocks (querying status register until
bit 1 goes off). If that doesn't happed during reasonable period assume
that the hardware doesn't have AT-style keyboard controller. This makes
FreeBSD working almost OOB on MacBook Pro (still there are issues with
putting second CPU core on-line, but since installation CD comes with
UP kernel with this change one should be able to install FreeBSD without
playing tricks with hints). Other legacy-free hardware (e.g. IBM NetVista
S40) should benefit from this as well, but since I don't have any I can't
verify.
It should make no difference on the ordinary i386 hardware (since in
that case that hardware already would be having an issues with A20
routines in boot blocks). I don't know much about AT-style keyboard
controller on other platforms (and don't have dedicated access to one),
therefore, the code is restricted to i386 for now. I suspect that amd64
may need this as well, but I would rather leave this decision to someone
who knows better about the platform(s) in question.
I have tested this change on as many "ordinary i386 boxes" as I can get
my hands on, and it doesn't create any false negatives on hardware with
AT-style keyboard present.
MFC after: 1 month
files after they were repo-copied to sys/dev/atkbdc. The sources of
atkbdc(4) and its children were moved to the new location in preparation
for adding an EBus front-end to atkbdc(4) for use on sparc64; i.e. in
order to not further scatter them over the whole tree which would have
been the result of adding atkbdc_ebus.c in e.g. sys/sparc64/ebus. Another
reason for the repo-copies was that some of the sources were misfiled,
e.g. sys/isa/atkbd_isa.c wasn't ISA-specific at all but for hanging
atkbd(4) off of atkbdc(4) and was renamed to atkbd_atkbdc.c accordingly.
Most of sys/isa/psm.c, i.e. expect for its PSMC PNP part, also isn't
ISA-specific.
- Separate the parts of atkbdc_isa.c which aren't actually ISA-specific
but are shareable between different atkbdc(4) bus front-ends into
atkbdc_subr.c (repo-copied from atkbdc_isa.c). While here use
bus_generic_rl_alloc_resource() and bus_generic_rl_release_resource()
respectively in atkbdc_isa.c instead of rolling own versions.
- Add sparc64 MD bits to atkbdc(4) and atkbd(4) and an EBus front-end for
atkbdc(4). PS/2 controllers and input devices are used on a couple of
Sun OEM boards and occur on either the EBus or the ISA bus. Depending on
the board it's either the only on-board mean to connect a keyboard and
mouse or an alternative to either RS232 or USB devices.
- Wrap the PSMC PNP part of psm.c in #ifdef DEV_ISA so it can be compiled
without isa(4) (e.g. for EBus-only machines). This ISA-specific part
isn't separated into its own source file, yet, as it requires more work
than was feasible for 6.0 in order to do it in a clean way. Actually
philip@ is working on a rewrite of psm(4) so a more comprehensive
clean-up and separation of hardware dependent and independent parts is
expected to happen after 6.0.
Tested on: i386, sparc64 (AX1105, AXe and AXi boards)
Reviewed by: philip
disabled.
- Change the apm driver to match the acpi driver's behavior by checking to
see if the device is disabled in the identify routine instead of in the
probe routine. This way if the device is disabled it is never created.
Note that a few places (ips(4), Alpha SMP) used "disable" instead of
"disabled" for their hint names, and these hints must be changed to
"disabled". If this is a big problem, resource_disabled() can always be
changed to honor both names.
problems currently experienced in -CURRENT.
This should fix the problem that the PS/2 mouse is detected
twice if the acpi module is not loaded on some systems.
more cleanly and consistently in all APCI, PnP BIOS, and "hint"
cases.
NOTE: this doesn't necessarily solve the problem that the PS/2
mouse is not detected after the recent ACPI update.
- Replace some very poorly thought out API hacks that should have been
fixed a long while ago.
- Provide some much more flexible search functions (resource_find_*())
- Use strings for storage instead of an outgrowth of the rather
inconvenient temporary ioconf table from config(). We already had a
fallback to using strings before malloc/vm was running anyway.
not u_long. On i386's with 64-bit longs, returning u_longs indirectly
in (more than) the space reserved for uintptr_t's tended to corrupt the
previous frame pointer in the stack frame, so it was not easy to debug.
The type mismatches are hidden by the bogus cast in DEVMETHOD().
device_add_child_ordered(). 'ivars' may now be set using the
device_set_ivars() function.
This makes it easier for us to change how arbitrary data structures are
associated with a device_t. Eventually we won't be modifying device_t
to add additional pointers for ivars, softc data etc.
Despite my best efforts I've probably forgotten something so let me know
if this breaks anything. I've been running with this change for months
and its been quite involved actually isolating all the changes from
the rest of the local changes in my tree.
Reviewed by: peter, dfr
- device_print_child() either lets the BUS_PRINT_CHILD
method produce the entire device announcement message or
it prints "foo0: not found\n"
Alter sys/kern/subr_bus.c:bus_generic_print_child() to take on
the previous behavior of device_print_child() (printing the
"foo0: <FooDevice 1.1>" bit of the announce message.)
Provide bus_print_child_header() and bus_print_child_footer()
to actually print the output for bus_generic_print_child().
These functions should be used whenever possible (unless you can
just use bus_generic_print_child())
The BUS_PRINT_CHILD method now returns int instead of void.
Modify everything else that defines or uses a BUS_PRINT_CHILD
method to comply with the above changes.
- Devices are 'on' a bus, not 'at' it.
- If a custom BUS_PRINT_CHILD method does the same thing
as bus_generic_print_child(), use bus_generic_print_child()
- Use device_get_nameunit() instead of both
device_get_name() and device_get_unit()
- All BUS_PRINT_CHILD methods return the number of
characters output.
Reviewed by: dfr, peter
