This merges in changes from NetBSD which ensure bktr0
(actually bktr%d) is printed at the start of any output lines.
Submitted by: Thomas Klausner <wiz@danbala.ifoer.tuwien.ac.at>
This is work-in-progress, and the entropy-gathering routines are not
yet present. As such, this should be viewed as a pretty reasonable
PRNG with _ABSOLUTELY_NO_ security!!
Entropy gathering will be the subject of ongoing work.
This is written as a module, and as such is unloadable, but there is
no refcounting done. I would like to use something like device_busy(9)
to achieve this (eventually).
Lots of useful ideas from: bde, phk, Jeroen van Gelderen
Reviewed by: dfr
severely stripped down compared with its predecessor, and is measurably
a _lot_ faster.
Many thanks to Jeroen van Gelderen for lots of good ideas.
There is still a problem with this; it is written as a mudule, and as
such is theoretically unloadable. However, there is no refcounting done
as I would prefer to do that a'la device_busy(9), rather than some
"home-rolled" scheme. The point is pretty moot, as /dev/null is
effectively compulsory.
Reviewed by: dfr
the PnP probe is merely a stub as we make assumptions about some of this
hardware before we have probed it.
Since these devices (with the exception of the speaker) are 'standard',
suppress output in the !bootverbose case to clean up the probe messages
somewhat.
Renamed varible dst in ray_rx to mp as it is a pointer to an mbuf.
Correctly grok addresses in data packets.
Promte a couple of RECERRs to real errors.
Rewrote intro at top of file to reflect my better understanding of how it
the memory mapping works.
Clear the DONE list and move some thoughts into the TODO list.
Remove RECERR from RAY_DEBUG
Start to use a desired network parameter structure, only used in download
code as I've realised that there are some problems with the idea.
Break up ray_rx, and move the data packet handler into a seperate function. This meant some knock on changes in ray_rx_mgt/ray_rx_ctl to do with
mbuf freeing.
Remove some debug code/XXX comments that are out of date.
Force alphas to prefer mem mapping as the default.
Basically, we have a pointer to a function which we can call which will
return us a pointer to firmware for the card we have. We call this function
(if it's non-NULL) with the address of our mdvec f/w pointer.
The way this works is that if ispfw (as a module or a static) is loaded,
it initializes the pointer in isp_pci, so we can call into to it to fetch
a pointer to a f/w set.
If ispfw is MOD_UNLOADed, it's retained a pointer to our mdvec f/w pointers,
which then get zeroed out so we don't have any references to data that's
now gone from kernel memory. Removing the f/w saves ~360KBytes.
Alas, there is no autounload mechanism that works for is here.
through, establish what our LUN width is. Unfortunately, we can't ask
the f/w. If we loaded the f/w, we'll now assume we have expanded LUNs
(SCCLUN for fibre channel, just plain 32 LUN for SCSI). If we didn't
load firmware, assume 8 LUNs for SCSI and 1 LUN for Fibre Channel. We
have to assume only one LUN for Fibre Channel because the LUN setting
in Request Queue entries is in different places whether we have SCCLUN
firmware or not, so the only LUN guaranteed to work for both is LUN 0.
Clean up the rest of isp.c so that ISP2100_SCCLUN defines aren't used-
instead use run time determinants based upon isp->isp_maxluns.
After starting firmware, delay 500us to give it a chance to get rolling.
Fix the interrupt service routine to check for both isr && sema being zero
before thinking this was a spurious interrupt. Following the manuals,
allow for both Mailbox as well as Queue Reponse type interrupts for regular
SCSI.
(we always support fabric now). Remove SCCLUN definition (we always
support SCCLUN now, if we load the f/w). Add typedef definition of an
external firmware fetch function.
