It uses new API from the part.c to work with partition tables.
Update userboot's disk driver to use new API. Note that struct
loader_callbacks_v1 has changed.
Discussed on hackers and recommended for inclusion into 9.0 at the devsummit.
All support email to devin dteske at vicor dot ignoreme dot com .
Submitted by: dteske at vicor dot ignoreme dot com
Reviewed by: me and many others
Add support for Pre-Boot Virtual Memory (PBVM) to the loader.
PBVM allows us to link the kernel at a fixed virtual address without
having to make any assumptions about the physical memory layout. On
the SGI Altix 350 for example, there's no usuable physical memory
below 192GB. Also, the PBVM allows us to control better where we're
going to physically load the kernel and its modules so that we can
make sure we load the kernel in memory that's close to the BSP.
The PBVM is managed by a simple page table. The minimum size of the
page table is 4KB (EFI page size) and the maximum is currently set
to 1MB. A page in the PBVM is 64KB, as that's the maximum alignment
one can specify in a linker script. The bottom line is that PBVM is
between 64KB and 8GB in size.
The loader maps the PBVM page table at a fixed virtual address and
using a single translations. The PBVM itself is also mapped using a
single translation for a maximum of 32MB.
While here, increase the heap in the EFI loader from 512KB to 2MB
and set the stage for supporting relocatable modules.
is determined by MD_IMAGE_SIZE. A file system can be embedded
into the loader with /sys/tools/embed_mfs.sh.
Note that md.c is not included when MD_IMAGE_SIZE is not set.
only when typing the sequence "123" (opposite to the standard 'push any
button' approach).
That results useful when using serial lines sending garbage and leading
to unwilling boot prompt appearence.
Obtained from: Sandvine Incorporated
Reviewed by: emaste, jhb
Sponsored by: Sandvine Incorporated
MFC: 1 week
This uses the common U-Boot support lib (sys/boot/uboot, already used on
FreeBSD/powerpc), and assumes the underlying firmware has the modern API for
stand-alone apps enabled in the config (CONFIG_API).
Only netbooting is supported at the moment.
Obtained from: Marvell, Semihalf
format modules, which are currently only used on the amd64 platform.
This initial implementation just parses enough of the module to
allow it to extract dependencies and load all the bits into the
right place in memory, so the kernel must still do the full relocation
and linking. The details of the loaded sections are passed to the
kernel by supplying a copy of the ELF section header table as module
metadata with the MODINFOMD_SHDR tag.
better relocation support for the amd64 and i386 platforms. This
should not result in any change in functionality, but moves a step
towards supporting the relocatable object file modules on amd64.
The same hack/trick as load_elf*.c uses is used here to simultaneously
support both elf32 and elf64 on amd64 and i386.
things over floppy size limits, I can exclude it for release builds or
something like that. Most of the changes are to get the load_elf.c file
into a seperate elf32_ or elf64_ namespace so that you can have two
ELF loaders present at once. Note that for 64 bit kernels, it actually
starts up the kernel already in 64 bit mode with paging enabled. This
is really easy because we have a known minimum feature set.
Of note is that for amd64, we have to pass in the bios int 15 0xe821
memory map because once in long mode, you absolutely cannot make VM86
calls. amd64 does not use 'struct bootinfo' at all. It is a pure loader
metadata startup, just like sparc64 and powerpc. Much of the
infrastructure to support this was adapted from sparc64.
this was quite broken, it never was updated for metadata support.
The a.out kld file support was never really used, as it wasn't necessary.
You could always load elf kld's, even in an a.out kernel.
As of this patchset, the loader builds (under NetBSD/macppc), boots, interacts
and talks to BOOTP/NFS servers.
(main.c was moved from boot/ofw/libofw to boot/ofw/common but has no revision
history)
Reviewed by: obrien
to the Forth interpreter. Instantiate all of our inbuilt commands
as Forth words, and handle them being called from there.
Add my copyright to the bcache module (oops).
and will bypass transfers for more than 8k. Blocks are invalidated after
2 seconds, so removable media should not confuse the cache.
The 8k threshold is a compromise; all UFS transfers performed by
libstand are 8k or less, so large file reads thrash the cache.
However many filesystem metadata operations are also performed using
8k blocks, so using a lower threshold gives poor performance.
Those of you with an eye for cache algorithms are welcome to tell me
how badly this one sucks; you can start with the 'bcachestats' command
which will print the contents of the cache and access statistics.
so far, and should probably be able to be made to work for the alpha
without too much trouble once it's connected up and my assumptions tested.
I think (but have not tested) it will also load "old" ELF kernels that
were not linked with DYNAMIC headers.
The module glue is yet to come. (oh fun.. :-)
It does not explicitly load symbols [yet]. The _DYNAMIC data contains a
runtime symbol set that ddb can use via ddb/db_kld.c. It'll be missing
some detail that stabs normally provides (eg: number of args to a function,
line numbers, etc). On the other hand, those minimal symbols will always
be available even on a stripped kernel.
This is mostly stolen from load_aout.c with some ideas from
alpha/libalpha/elf_freebsd.c.
- Use format-independant module allocator.
- Conditionalise ISA PnP support.
- Simplify PnP enumerator interface.
- Improve module/object searching.
- Add missing depend/install targets in BTX makefiles.
- Pass the kernel environment and module data in extended bootinfo fields.
- Add a pointer to the end of the kernel + modules in bootinfo.
- Fix parsing of old-style kernel arguments.
- Implement a new copyin/readin interface for loading modules.
This allows the module loaders to become MI, reducing code duplication.
- Simplify the search for an image activator for the loaded kernel.
- Use the common module management code for all module metadata.
- Add an 'unload' command that throws everything away.
- Move the a.out module loader to MI code, add support for a.out
kld modules.
Submitted by: Alpha changes fixed by Doug Rabson <dfr@freebsd.org>
'three-stage' bootstrap.
There are a number of caveats with the code in its current state:
- The i386 bootstrap only supports booting from a floppy.
- The kernel and kld do not yet know how to deal with the extended
information and module summary passed in.
- PnP-based autodetection and demand loading of modules is not implemented.
- i386 ELF kernel loading is not ready yet.
- The i386 bootstrap is loaded via an ugly blockmap.
On the alpha, both net- and disk-booting (SRM console machines only) is
supported. No blockmaps are used by this code.
Obtained from: Parts from the NetBSD/i386 standalone bootstrap.
