The default priority is now '1000' rather than '0'. This may cause some
unforseen regressions.
Submitted by: Stefan Bethke <stb@lassitu.de>
Reviewed by: imp
- When switching to 4-bit operation, send a SET_CLR_CARD_DETECT command
to disconnect the card-detect pull-up resistor from the DAT3 line before
sending the SET_BUS_WIDTH command.
- Add the missing "reserved" zero entry to the mantissa table used to
decode various CSD fields. This was causing SD cards to report that they
could run at 30 MHz instead of the maximum 25 MHz mandated in the spec.
o Enhancements:
- At the MMC layer, format various info from the CID into a string that
uniquely identifies the card instance (manufacturer number, serial
number, product name and revision, etc). Export it as an instance
variable.
- At the MMCSD layer, display the formatted card ID string, and also
report the clock speed of the hardware (not the card's max speed), and
the number of bits and number of blocks per transfer. It comes out like
this now:
mmcsd0: 968MB <SD SD01G 8.0 SN 276886905 MFG 08/2008 by 3 SD> at mmc0
22.5MHz/4bit/128-block
o Use DEVMETHOD_END.
o Use NULL instead of 0 for pointers.
PR: 156496
Submitted by: Ian Lepore
MFC after: 1 week
sys/contrib/rdma/rdma_cma.c:1259:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ECONNRESET:
^
@/sys/errno.h:118:20: note: expanded from macro 'ECONNRESET'
#define ECONNRESET 54 /* Connection reset by peer */
^
sys/contrib/rdma/rdma_cma.c:1263:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ETIMEDOUT:
^
@/sys/errno.h:124:19: note: expanded from macro 'ETIMEDOUT'
#define ETIMEDOUT 60 /* Operation timed out */
^
sys/contrib/rdma/rdma_cma.c:1260:8: error: case value not in enumerated type 'enum iw_cm_event_status' [-Werror,-Wswitch]
case ECONNREFUSED:
^
@/sys/errno.h:125:22: note: expanded from macro 'ECONNREFUSED'
#define ECONNREFUSED 61 /* Connection refused */
^
This is because the switch uses iw_cm_event::status, which is an enum
iw_cm_event_status, while ECONNRESET, ETIMEDOUT and ECONNREFUSED are
just plain defines from errno.h.
It looks like there is only one use of any of the enumeration values of
iw_cm_event_status, in:
sys/contrib/rdma/rdma_iwcm.c: if (iw_event->status == IW_CM_EVENT_STATUS_ACCEPTED) {
So messing around with the enum definitions to fix the warning seems too
disruptive; the simplest fix is to cast the argument of the switch to
int.
Reviewed by: kmacy
MFC after: 1 week
sys/dev/nxge/if_nxge.c:1276:11: error: case value not in enumerated type 'xge_hal_event_e' (aka 'enum xge_hal_event_e') [-Werror,-Wswitch]
case XGE_LL_EVENT_TRY_XMIT_AGAIN:
^
sys/dev/nxge/if_nxge.c:1289:11: error: case value not in enumerated type 'xge_hal_event_e' (aka 'enum xge_hal_event_e') [-Werror,-Wswitch]
case XGE_LL_EVENT_DEVICE_RESETTING:
^
This is because the switch uses xge_queue_item_t::event_type, which is
an enum xge_hal_event_e, while the XGE_LL_EVENT_xx values are of the
enum xge_event_e.
Since messing around with the enum definitions is too disruptive, the
simplest fix is to cast the argument of the switch to int.
Reviewed by: gnn
MFC after: 1 week
STAILQ(). While here, fix another clang warning about a switch which
tests an enum type for a regular integer value.
Submitted by: jhb
MFC after: 1 week
assumes for small buffers (< 64k) that the OS driver is actually using
a buffer rounded up to the next power of 2. It also assumes that the
buffer is at least 4k in size. Furthermore, there is at least one
known instance of megarc sending a request with a 12k buffer where the
firmware writes out a 24k-ish reply.
To workaround the data corruption triggered by this "feature", ensure
that buffers for user commands use a minimum size of 32k, and that
buffers between 32k and 64k use a 64k buffer.
PR: kern/155658
Submitted by: Andreas Longwitz longwitz incore de
Reviewed by: scottl
MFC after: 1 week
code that is used to construct a loader (e.g. libstand, ficl, etc).
There is such a thing as a 64-bit EFI application, but it's not
as standard as 32-bit is. Let's make the 32-bit functional (as in
we can load and actualy boot a kernel) before solving the 64-bit
loader problem.
ar724x_pci.c.
* Move out the code which populates the firmware into ar71xx_fixup.c
* Shuffle around the ar724x fixup code to match what the ar71xx fixup
code does.
I've validated this on an AR7240 with AR9285 on-board NIC. It doesn't
yet load, as the AR9285 EEPROM code needs to be made "flash aware."
TODO:
* Validate that I haven't broken AR71xx
* Test AR9285/AR9287 onboard NICs, complete with EEPROM code changes
* Port over the needed BAR hacks for AR7240, AR7241 and AR7242 from
Linux OpenWRT. The current WAR has only been tested on the AR7240
and I'm not sure the way the BAR register is treated is "right".
The "fixup" method here is right when setting the BAR for local access -
ie, the BAR address is either 0xffff (AR7240) or 0x1000ffff (AR7241/AR7242),
but the ath9k-fixup.c code (Linux OpenWRT) does this when setting the
initial "fixup" BAR. It then restores the original BAR.
I'll have to read the ar724x PCI bus glue to see what other special cases
await.
over just the active vnodes associated with a mount point to replace
MNT_VNODE_FOREACH_ALL in the vfs_msync, ffs_sync_lazy, and qsync
routines.
The vfs_msync routine is run every 30 seconds for every writably
mounted filesystem. It ensures that any files mmap'ed from the
filesystem with modified pages have those pages queued to be
written back to the file from which they are mapped.
The ffs_lazy_sync and qsync routines are run every 30 seconds for
every writably mounted UFS/FFS filesystem. The ffs_lazy_sync routine
ensures that any files that have been accessed in the previous
30 seconds have had their access times queued for updating in the
filesystem. The qsync routine ensures that any files with modified
quotas have those quotas queued to be written back to their
associated quota file.
In a system configured with 250,000 vnodes, less than 1000 are
typically active at any point in time. Prior to this change all
250,000 vnodes would be locked and inspected twice every minute
by the syncer. For UFS/FFS filesystems they would be locked and
inspected six times every minute (twice by each of these three
routines since each of these routines does its own pass over the
vnodes associated with a mount point). With this change the syncer
now locks and inspects only the tiny set of vnodes that are active.
Reviewed by: kib
Tested by: Peter Holm
MFC after: 2 weeks
a mount point. Active vnodes are those with a non-zero use or hold
count, e.g., those vnodes that are not on the free list. Note that
this list is in addition to the list of all the vnodes associated
with a mount point.
To avoid adding another set of linkage pointers to the vnode
structure, the active list uses the existing linkage pointers
used by the free list (previously named v_freelist, now renamed
v_actfreelist).
This update adds the MNT_VNODE_FOREACH_ACTIVE interface that loops
over just the active vnodes associated with a mount point (typically
less than 1% of the vnodes associated with the mount point).
Reviewed by: kib
Tested by: Peter Holm
MFC after: 2 weeks
actually in it. This happens when SCTP receives an unknown chunk, which
requires the sending of an ERROR chunk, and there is no final padding but
the chunk is not 4-byte aligned.
Reported by yueting via rwatson@
MFC after: 3 days
at least until I can root cause what's going on.
The only platform I've seen this on is the AR9220 when attached to
the AR71xx CPUs. I get immediate PCIe bus errors and all subsequent
accesses cause further MIPS bus exceptions. I don't have any other
big-endian platforms to test this on.
If I get a chance (or two), I'll try to whack this on a bus analyser
and see exactly what happens.
I'd rather leave this on, especially for slower, embedded platforms.
But the #ifdef hell is something I'm trying to avoid.
- Implement "configure" command to allow switching operation mode of
running device on-fly without destroying and recreation.
- Implement Active/Read mode as hybrid of Active/Active and Active/Passive.
In this mode all paths not marked FAIL may handle reads same time,
but unlike Active/Active only one path handles write requests at any
point in time. It allows to closer follow original write request order
if above layers need it for data consistency (not waiting for requisite
write completion before sending dependent write).
- Hide duplicate messages about device status change.
- Remove periodic thread wake up with 10Hz rate.
MFC after: 2 weeks
Sponsored by: iXsystems, Inc.
used only as a helper function in that file. Replace sole call to
vbusy() with inline code in vholdl(). Replace sole calls to vfree()
and vdestroy() with inline code in vdropl().
The Clang compiler already inlines these functions, so they do not
show up in a kernel backtrace which is confusing. Also you cannot
set their frame in kgdb which means that it is impossible to view
their local variables. So, while the produced code is unchanged,
the debugging should be easier.
Discussed with: kib
MFC after: 2 weeks
The primary changes are that the user of the interface no longer
needs to manage the mount-mutex locking and that the vnode that
is returned has its mutex locked (thus avoiding the need to check
to see if its is DOOMED or other possible end of life senarios).
To minimize compatibility issues for third-party developers, the
old MNT_VNODE_FOREACH interface will remain available so that this
change can be MFC'ed to 9. Following the MFC to 9, MNT_VNODE_FOREACH
will be removed in head.
The reason for this update is to prepare for the addition of the
MNT_VNODE_FOREACH_ACTIVE interface that will loop over just the
active vnodes associated with a mount point (typically less than
1% of the vnodes associated with the mount point).
Reviewed by: kib
Tested by: Peter Holm
MFC after: 2 weeks
allow the owner to read and write ACL and file attributes when there
was no entry with subject matching the owner. In other words,
'getfacl meh' shouldn't fail for the owner if the ACL looks like this:
# file: meh
# owner: trasz
# group: wheel
user:root:------a-------:------:allow
Reported by: kientzle
like the one triggered by this:
# kldload geom_vinum
# pwait `pgrep -S gv_worker` &
# kldunload geom_vinum
or this:
GEOM_JOURNAL: Shutting down geom gjournal 3464572051.
panic: destroying non-empty racct: 1 allocated for resource 6
which were tracked by jh@ to be caused by checking p->p_flag,
while it wasn't initialised yet. Basically, during fork, the code
checked p_flag, concluded the process isn't marked as P_SYSTEM,
incremented the counter, and later on, when exiting, checked that
the process was marked as P_SYSTEM, and thus didn't decrement it.
Also, I believe there wasn't any good reason for checking P_SYSTEM
in the first place.
Tested by: jh
even in the face of errors.
If the RX descriptor list fails, the RX lock won't be initialised, but
then the DMA free path wil try freeing it.
This commit is brought to you by a working mwl(4).
