(r225485). When setting an interface name to it, the following
configurations will be enabled:
1. "no_radr" is set to all IPv6 interfaces automatically.
2. "-no_radr accept_rtadv" will be set only for $ipv6_cpe_wanif. This is
done just before evaluating $ifconfig_IF_ipv6 in the rc.d scripts (this
means you can manually supersede this configuration if necessary).
3. The node will add RA-sending routers to the default router list
even if net.inet6.ip6.forwarding=1.
This mode is added to conform to RFC 6204 (a router which connects
the end-user network to a service provider network). To enable
packet forwarding, you still need to set ipv6_gateway_enable=YES.
Note that accepting router entries into the default router list when
packet forwarding capability and a routing daemon are enabled can
result in messing up the routing table. To minimize such unexpected
behaviors, "no_radr" is set on all interfaces but $ipv6_cpe_wanif.
Approved by: re (bz)
Print a separate "Additional routing options" line for each address family
which has additional options, so that it does not get mixed up with the
output from adding routes.
This also reverts r224048 which added newlines to two arbitrary routing
options.
longer used by /etc/rc.d/nfsd and it is no longer necessary
to load the old nfs server by default, when nfs_server_enable="YES".
Tested by: sgk at troutmask.apl.washington.edu
Reviewed by: rc (Andrzej Tobola)
can use the "-o" option to force the old NFS server to run.
Running the old NFS server is enabled by setting
oldnfs_server_enable="YES". The scripts will only enable
providing service for NFSv4 if nfsv4_server_enable="YES"
is set.
Reviewed by: dougb (rc)
times mount is called.
Limit the automatic behavior to when AUTO is specified (as it is in
etc/defaults/rc.conf) and for everything else take advantage of all
of the goodness in checkyesno.
like, determines the path to a pid file as it is specified in a conf file.
Use the new feature for rc.d/named and rc.d/devd, the 2 services in the
base that list their pid files in their conf files.
Remove the now-obsolete named_pidfile, and warn users if they have it set.
The old version had a race between the time that the old file was
cp'ed to acct.0 and the time that 'sa -s' was run that prevented
the commands that occurred in the meantime from being backed up.
It's also arguable that the old version was inefficient in using
cp which can be a problem on a space-constrained system.
This version avoids both problems, albeit it's considerably more
complicated. The advantage of putting the log rotation in the rc.d
script is that it can handle the _enable and _file questions without
having to do gymnastics to discover either value in the periodic script.
As a side effect of reviewing the rc.d script I cleaned it up a bit.
While I'm here, don't run the sysctl frob unconditionally, and
s/sysctl/$SYSCTL/
PR: conf/153460 [1]
Submitted by: Grigory Rechistov <ggg_mail@inbox.ru>
case user wants to implement his own actions and doesn't want the attributes to
vanish.
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 3 days
set to use DHCP have no carrier. This can cause grief as it may take
some time for link to be established, and defaultroute may terminate
before this happens.
Introduce a defaultroute_carrier_delay variable and then wait that long
in defaultroute before bailing if no interfaces have carrier. With the
default settings defaultroute will wait for five seconds for this, and
the original 30 second wait for a default route to appear is unchanged.
Note that there is in discussion an alternative approach to the broader
problem of waiting for DHCP-configured routes. However, this change
addresses a real problem in the current defaultroute script.
Discussed on: freebsd-rc@
- looking for partition with 'bootonce' attribute alone (without 'bootme'
attribute), removing it and logging that we successfully booted from this
partition.
- looking for partitions with 'bootfailed' attribute, removing it and
logging that we failed to boot from this partition.
Reviewed by: arch (Message-ID: <20100917234542.GE1902@garage.freebsd.pl>)
Obtained from: Wheel Systems Sp. z o.o. http://www.wheelsystems.com
MFC after: 2 weeks
The $ip6addrctl_policy is a variable to choose a pre-defined address
selection policy set by ip6addrctl(8).
The keyword "ipv4_prefer" sets IPv4-preferred one described in Section 10.3,
the keyword "ipv6_prefer" sets IPv6-preferred one in Section 2.1 in RFC 3484,
respectively. When "AUTO" is specified, it attempts to read
/etc/ip6addrctl.conf first. If it is found, it reads and installs it as
a policy table. If not, either of the two pre-defined policy tables is
chosen automatically according to $ipv6_activate_all_interfaces.
When $ipv6_activate_all_interfaces=NO, interfaces which have no corresponding
$ifconfig_IF_ipv6 is marked as IFDISABLED for security reason.
The default values are ip6addrctl_policy=AUTO and
ipv6_activate_all_interfaces=NO.
Discussed with: ume and bz
(in /etc/rc.conf).
This fixes an apparent confusion between test(1) and sh(1) syntax for
AND/OR.
PR: conf/149036
Submitted by: pluknet
MFC after: 1 week
FILESYSTEMS (the default early_late_divider):
1. Move sysctl to run first
2. Move as many BEFOREs to REQUIREs as possible.
3. Minor effect, move hostid_save from right before mdconfig to right
after.
A lot of the early scripts make use of sysctl one way or another so
running this first makes a lot of sense given that system-critical
values are often placed in sysctl.conf.
My original purpose for working on this was that while doing some
debugging on other stuff I noticed that the order of execution was
different in the first pass through the early scripts and the second.
In practice that doesn't matter because the scripts are not executed the
second time. However this _can_ result in problems if the difference in
the rcorder moves a script from the late section to the early section in
the second pass (which would mean the script would not get executed).
So, I wanted to make the order of execution of the scripts in the early
section more deterministic.
In the course of debugging the ordering problems I noticed that moving
the BEFOREs to REQUIREs prevented the changes in order from the first
pass to the second pass without having to make any substantial changes.
(Of course it's no secret that I think BEFORE should be avoided as much
as possible, but this is a good example of why.)
Reviewed by: silence on freebsd-rc@
MFC after: 8.1-RELEASE
named_chrootdir IS set, named-checkconf fails because it
cannot find the conf file. Fix this by making checkconf a
variable that includes "-t $named_chrootdir" as needed.
Notice of the bug and suggested direction for the fix from [1].
Using required_files for named.conf is overkill ever since
I added the named-checkconf call, so rather than update the
logic to handle the case described above, remove it. This
also handles the case where named_chroot_autoupdate IS set
but the symlink doesn't exist yet.
PR: conf/145904
Submitted by: J R Matthews
