to the virtual one. I may had a reason at some point to use the later, but
can't remember which, and it can leads to issues.
Reported by: Guillaume Ballet <gballet gmail com>
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
driver in Linux 2.6. uscanner was just a simple wrapper around a fifo and
contained no logic, the default interface is now libusb (supported by sane).
Reviewed by: HPS
to the full path of the image that is being executed.
Increase AT_COUNT.
Remove no longer true comment about types used in Linux ELF binaries,
listed types contain FreeBSD-specific entries.
Reviewed by: kan
".note.ABI-tag" section.
The search order of a brand is changed, now first of all the
".note.ABI-tag" is looked through.
Move code which fetch osreldate for ELF binary to check_note() handler.
PR: 118473
Approved by: kib (mentor)
operate on the resource (we have no local resources to manage); this
fixes drivers that alloc/release resources in their probe method and
then do it again in attach
o while here add some prints to catch failures and massage style a bit
o encode need for A4 bus space tag hackery according to the memory
address; checking for "uart" breaks down with the GPS chip support
which is also a uart but does not require the same hackery
o encode the correct memory window instead of carving up all of i/o
space, potentially with a larger window than a device should have;
this likely should be handled in the drivers by using a proper bus
alloc call but since some drivers depend on the bus support to figure
this out we cannot simply mod them
o add optional GPS and RS485 support (conditionally as the support
isn't ready yet)
o improves understandability by replacing numerous relative address
calculations with fixed addresses; everything should now match up
more easily with the vm layout shown at the top of the file
o move the expansion bus chip select regions to be contiguous with
the expansion bus configuration area; this is not exploited right
now but allows map consolidation in the future
o leave a gap between the expansion bus regions and the pci config
space in case we want to map more exp bus cs regions
Reviewed by: imp, thompsa
usb stack rather than with the rest of the processor support code.
Not sure that's a good idea, as we were moving away from it, but this
fixes the build in the mean time so we can have that discussion.
the same dma tag. However, it can happen multiple dma tags share the same
bounce zone too, so add a per-bounce zone map counter, and check it instead of
the dma tag map counter, to know if we have to alloc more pages.
Reported by: miwi
Reviewed by: scottl
offset. This is needed for the ehci hardware buffer rings that assume
this behavior.
This is an interim solution, and a more general one is being worked
on. This solution doesn't break anything that doesn't ask for it
directly. The mbuf and uio variants with this flag likely don't work
and haven't been tested.
Universe builds with these changes. I don't have a huge-memory
machine to test these changes with, but will be happy to work with
folks that do and hps if this changes turns out not to be sufficient.
Submitted by: alfred@ from Hans Peter Selasky's original
o add bus shim for cfi driver
o add static mapping for CS0 (we map all 16M as the cfi driver doesn't
support demand mapping)
Note this needs some tweaking to work for 2358 boards which is why the
CAMBRIA config is not touched.
rather than a fixed 512... This fixes the mount root problem on at91.
Prior to the SD card reorg, all data transfers were 512 bytes, so we
didn't notice.
the serial port class when we set the devclass since it is now
no-longer a compile time constant. Eliminate the pci include, as it
isn't relevant or necessary.
time constant. This allows us to potentially change it at runtime or
autodetect it early in the boot (the latter being much more likely to
have a good outcome).
