o Allow a forth argument in ppp.secret, specifying a new
label. This gives control over which section of
ppp.link{up,down} is used based on the authenticated user.
o Support random address ranges in ppp.secret (not just in ppp.conf).
o Add a AUTHENTICATING INCOMING CONNECTIONS section to the man page.
o Add a bit more about DEFLATE in the man page.
o Fix the incorrect "you must specify a password in interactive
mode" bit of the manual.
o Space things in the man page consistently.
o Be more precice about where you can use MYADDR, HISADDR and INTERFACE
in the "add" command documentation.
not in -auto mode isn't a good idea, and that the
add should be done in ppp.linkup instead.
Change "add 0 0 HISADDR" to "add default HISADDR". It's
more intuitive.
RTM_CHANGE if the RTM_ADD fails with an EEXIST.
Allow "delete! dst" (note the ``!'') to silently
fail if the RTM_DELETE fails with an ESRCH.
Also, make the ESRCH and EEXIST error conditions
more understandable to the casual observer.
when command logging is switched on.
o Display ******** for the authkey for "show auth"
o Document how \P should be used, and document the other chat escapes
while I'm there.
o Make sure the full command is displayed when a compound command
fails - ie, "set novar rubbish" should say "set novar: Invalid command"
rather than "novar: Invalid command"
Problem pointed out by: Theo de Raadt <deraadt@cvs.openbsd.org> (among others)
Validate the peers suggested IP by attempting to make a routing table
entry.
Give up IPCP negotiation if the peer NAKs us with an unusable IP.
Always SIOCDIFADDR then SIOCAIFADDR when configuring the tun device.
Using SIOCSIFDSTADDR allows duplicate dst addresses (which we don't
want)!!!
Allow up to 200 interface names (was 50) (now that ppp can play server
properly).
Up the version number (1.5 -> 1.6).
Cosmetic:
Log unexpected CCP packets in the CCP log rather than the ERROR log.
Log unexpected Config Reqs in the appropriate LCP/IPCP/CCP log rather
than the ERROR log.
Log failed route additions and deletions with WARN, not TCPIP.
Log the option id and length for unrecognised IPCP options.
Change some .Sq to .Ar in the man page.
Delete AF_LINK routes as well as AF_INET.
Allow the word `default' as the arg to `delete' or in place of the
first two args (dest & netmask) to `add'.
Accept INTERFACE as the third arg to `add'.
You can now say `add default interface' to create a default route
through the tun interface. It's reported that subsequent bind()s
will bind to a broadcast address and not to the address currently
assigned to the tun device - this is the first step towards
supporting that first connection that was around from before the
dynamic IP negotiation....
(I *really* meant to do this *before* committing the
deflate changes in the first place - oops).
Pppd is horribly broken in this respect - refer to the
ppp man page for details. Ppp *WON'T* negotiate deflate
with pppd by default - you must ``enable'' and ``accept''
``pppd-deflate'' in your config.
While I'm in there, update the cftypes in ccp.c so that
we recognise some more protocols (we don't actually do
anything with them - just send a REJ).
o Add "allow" command:
"allow users a b c" gives access to users a, b and c.
"allow modes auto" gives those users access to auto mode only.
"allow users *" and "allow modes *" are accepted.
No users and all modes are allowed by default.
UID 0 can do anything.
o Set the current label with the "load" and "dial" commands
so that the call to ppp.linkdown makes sense.
o Up the verison number.
o Don't OR MODE_AUTO for -background and -ddial.
o Don't OR MODE_INTER when we get a diagnostic connection.
o Allow up to 40 args per line (was 20).
o "set ifaddr" only changes the interface in AUTO mode (with other
modes, it happens after IPCP negotiation).
o Sort command descriptions in the man page.
o Support -dedicated mode where we just talk ppp forever (no login etc).
Stay as the invoking uid as much as possible.
Execution as a normal user is still forbidden for now,
so these changes are pretty ineffective.
The next commit will implement the modifications suggested
on -hackers a number of days ago.
Insist that uid == 0 for client ppp
Disallow client sockets if no password is specified
Don't exit on failure to open client socket for listening
Allow specification of null local password
Use reasonable size (smaller) ``vector''s in auth.c
Fix "passwd ..." usage message
Insist on "all" as arg to "quit" (if any)
Drop client socket connection before Cleanup() when "quit all"
This tells ppp to loopback packets addressed to
the ppp interface IP coming *from* the tun
device.
This means that you can ping the tun interface IP
from inside :-)
idependently time out any of the FSMs.
Split LCP logging into LCP, IPCP and CCP logging,
and make room in "struct fsm" for the log level
that the state machine should use.
"set stopped" directive. If the timeout occurs
it will cause a "Down" event, hanging up the line
if it's still up. This *isn't* part of the FSM
diagram, but I consider it ok as a "higher level
implementation specific timeout" as specified in
the rfc ;-}
Discussed briefly with: joerg
INT cause a hangup - not exiting for -ddial & -auto.
HUP must exit because init sends this at system shutdown
time (why, I don't know), and we don't want to end up
redialing after the HUP (due to another dfilter packet).
Pointed out by and discussed with: ache
Catch SIGUSR1 to re-init listening socket.
Document signal behaviour.
Add missing '\n's to LogPrintf(LogWARN,...)
Main() returns int not void.
AF_LOCAL ideal suggested a long time ago by: joerg
Submitted by: Forgotten
Passed on by: Terry Dwyer 61 8 9491 5161 <tdwyer@io.telstra.com.au>
Also remove extraneous setuid(0) - it's only undone by
the subsequent call to SelectSystem().
of reconnect & -background.
o Fix reconnect anomolies.
o Make reconnect apply to failed LQR hangups (& mention in man page).
o Make reconnect effective in -background mode.
o Listen on socket in -background mode.
o Try all phone numbers in -background mode.
o Insist on system arg in -background mode.
o Make a control-connection close command exit in -background mode.
o Output status message to stdout on exit of parent in -background mode.
o Don't notify parent of success too soon.
o Describe termination EX_* code.
o Miscelaneous diagnostic corrections.
o Remove redundant connect_time from modem.c.
o Don't repeatedly DownConnection().
the connection after an unexpected loss of carrier:
set reconnect timer ntries
The man page warns against using this command when your
timeout value is slightly more than the other sides :{}
Suggested by: burton@bsampley.vip.best.com (Burton Sampley)
list has been dialed. Alternate number dialing has no "pause".
Suggested by: joerg
Document this behaviour. Document that the number of dial attempts
applies to the number of phone calls rather than the number of times
each number is dialed. Add a missing .El. Give a decent description
of how to connect to an ISP.
This will make a number of things easier in the future, as well as (finally!)
avoiding the Id-smashing problem which has plagued developers for so long.
Boy, I'm glad we're not using sup anymore. This update would have been
insane otherwise.
connecting to a host immediately in the foreground.
I would like to be able to run ppp from a script so that my script can be
sure that it is connected to the 'net before it continues running:
# Dial up the internet.
ppp -background myprovider || exit 1
do-some-net-command
# Hang up the modem.
kill -HUP `cat /var/run/ppp.tun0.pid`
Another problem is that the current ppp calls its process id file
`/var/run/PPP.server', which may conflict if you have more than one IP
tunnel interface available.
Closes PR#1469
Submitted by: Gord Matzigkeit <gord@enci.ucalgary.ca>
(otherwise ppp's behavior remains unchanged) and documented by myself,
Steve Sims, Nate Williams, Martin Renters and god-only-knows who else. :-)
Submitted by: nate
Obtained from: Charles Mott <cmott@srv.net>
to keep the link up, so it re-dials whenever it detects the link go
down. This is useful for 'dedicated' links who use PPP.
It's been used for over a year w/out problems at different sites.
on their own without even attempting to get concensus in the IETF, but
there are also lots of Win95/NT boxes out there.
CLoses PR#1494
Submitted-By: Peter Childs <pjchilds@imforei.apana.org.au>
add some logging functionality which I find very useful.
'set debug link' will record just link up/down and address assignments.
'set debug connect' will record the entire chat dialog
'set debug carrier' will record just chat lines including 'CARRIER'
(so that I can be sure I'm getting a 28.8 line).
There was a global change required to permit LogPrintf to take a bit
mask instead of a bit position value (to permit logging some events
on either of two flags, so that no change in 'set debug lcp' would
result from the code supporting 'link'. Thus the diffs are rather
long for such a small change. The man page is also touched.
Oh, and there was a slight syntax problem in route.c
Reviewed by: phk
Submitted by: Tony Kimball <alk@Think.COM>
*not* our controlling terminal (SIGHUP can coming in other case)
2) Add HUPCL for non-dedicated lines to be shure that modem
properly resetted.
3) Correct usage string.
2) Improve on-line help subsystem
3) Make 'term' mode works even carrier dropped (old code
close line forever here)
4) Make 'term' mode 8bit clean.
5) Improve manual page
6) #ifdef DEBUG diagnostic about missing optional files.
7) Don't put interactive dialing info to logfile
A settable redial timer helps to avoid the problem where both ends
of a link want to dial at the same time and the line winds up busy
for both ends. The process id is logged in /var/run/PPP.system where
system is the name of the called system. When both ends of a link
are running in demand dial mode, you need an easy way to get the pid
of the ppp on the called end so it can be killed and re-started with
-direct or pppd started to handle the incoming ppp session.
2. Add secret description for "set timeout" to man.
Reviewed by: Atsushi Murai <amurai@spec.co.jp>
Submitted by: John Capo <jc@irbs.com>
dropped - devet@adv.IAEhv.nl (Arjan de Vet)
2. Will not read data from telnet connection - John Capo <jc@irbs.com>
3. Using LQM option could be drop the link due to LcpLayerDown() doesn't
stop LQR timer. - Brian <brian@awfulhak.demon.co.uk>
4. Allow to describe a syntax of filters that is not only port number
but also by name in /etc/service. - Rich Murphey <rich@lamprey.utmb.edu>
Reviewed by: Atsushi Murai <amurai@spec.co.jp>
Submitted by: devet@adv.IAEhv.nl, jc@irbs.com, brian@awfulhak.demon.co.uk,
rich@lamprey.utmb.edu
o Supporting SYNC SIO device (But need a device driver)
- add "set speed sync"
o Fixing bug for Predictor-1 function.
o Add new parameter that re-sent interval for set timeout commands.
o Improving RTT (Round Trip Time) and reducing processor time.
- Previous Timer service was using polling, and now using
SIGALRM ;-)
- A 0.94beta2 will not work correctly....
-- Follows are additinal feature not including 0.94beta2
o Support Proxy ARP
- add "enable/disable proxy" commands
o Marging common routine in CHAP/PAP.
o Enhancing LCP/IPCP log information.
o Support local Authfication connection on port 300x and tty.
- You can set up pair of your "hostname -s" and
password in ppp.secret. if either ppp.secret file nor
your hostname line don't exist, It will notify a message
and working as same as previous version.(Backword compatibility)
- If you did set up them, It's allow connection but nothing to do
except help and passwd command.
- add "passwd yourpasswd" commands
o Support afilter - keep Alive filter that a packet can send/receiving
according to ifilter/ofilter but doesn't count it as preventing idle
timer expires.
- Same syntax of other filters.
o Fixing bugs reported by current user for previous one. Thanks !!
Reviewed by: Atsushi Murai (amurai@spec.co.jp)
