doesn't support winmodems, softmodems, hcf or any other modem that
relies on the host to do any sort of soft control for any aspect of
the modem's function. There are two modems known to work:
3COM FaxModem PCI.
ActionTec 56k VoiceMessaging PCI Modem
and the following modem might work
Multitech PCI FaxModem (not sure about this)
and the serial pci cards might work too. I have neither these
hardware items so I can't add support for them.
release for inclusion into the release, but bde talked me out of
committing the module that needs this until after the release. It is
after the release now. :-)
- Add periodic status monitoring routine. Currently just detects
lost commands, further functionality pending data from AMI.
Add some new commands states; WEDGED (never coming back) and
LATE (for when a command that wasmarked as WEDGED comes bacj,
- Remove a number of redundant efforts to poll the card for completed
commands. This is what interrupt handlers are for.
- Limit the maximum number of outstanding I/O transactions. It seems
that some controllers report more than they can really handle,
and exceding this limit can cause the controller to lock up.
- Don't use 'wait' mode for anything where the controller might not
be able to generate interrupts. (Keep the 'wait' mode though sa it
will become useful when we start taking userspace commands.
- Use a similar atomic locking trategy to the Mylex driver to prevent
some reentrancy problems.
- Correctly calculate the block count for non-whoile-bloch transfers
(actually illegal).
- Use the dsik device's si_drv1 field instead of b_driver1 in the
buf struct to pass the driver identifier arond.
- Rewrite amr_start and amr_done() along the lines of the Mylex driver
in order to improve robustnes.
- Always force the PCI busmaster bit on.
INADDR_NONE: Incoming packets go to the alias address (the default)
INADDR_ANY: Incoming packets are not NAT'd (direct access to the
internal network from outside)
anything else: Incoming packets go to the specified address
Change a few inaddr::s_addr == 0 to inaddr::s_addr == INADDR_ANY
while I'm there.
redirected and when no target address has been specified, NAT
the destination address to the alias address rather than
allowing people direct access to your internal network from
outside.
This don't hurt anything.
PCI/CardBus Bridge -> PCI-CardBus Bridge
Submitted by: Takeshi Shibagaki <sibagaki@lsi.melco.co.jp>
Obtained from: bsd-nomads ML in Japan
via sysctl. It's done pretty simply but it should be quite adequate.
Also move SHMMAXPGS from $machine/include/vmparam.h as the comments that
went with it were wrong... we don't allocate KVM space for the pages so
that comment is bogus.. The only practical limit is how much physical
ram you want to lock up as this stuff isn't paged out or swap backed.
mbuf is marked for delayed checksums, then additionally mark the
packet as having it's checksums computed. This allows us to bypass
computing/checking the checksum entirely, which isn't really needeed
as the packet has never hit the wire.
Reviewed by: green
- Only call m_pullup() when necessary.
- Check return value from rl_encap() in rl_start() to avoid panic when
we run out of mbufs. (Fixes PR kern/17582)
PR: kern/17582
- Move dev/aic/aic_isa.c entry from conf/files to conf/files.MACHINE
because PC-98 uses different file.
Submitted by: nyan and IMAI Takeshi <take-i@ceres.dti.ne.jp>
shows `CPUID' and it is useful to identify CPU. So, it is copied from
BIOS work area to the cpu_id variable (PC-98 only).
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
fe_read_eeprom_rex() and fe_init_rex(). These functions should be
useful for REX-5580 series (for PC-AT). But they are included in
`#ifdef PC98' to avoid warnings by unused static functions. If you
try to support REX-5580, please be aware of these functions.
Submitted by: chi@bd.mbn.or.jp (Chiharu Shibata)
