exactly as done in the cmi driver. I am quite confident this is
safe since I'm runing this for more than two weeks now, on an SMP
box. A few people tested this patch for me successfully as well.
proper locking to be checked at runtime.
Remove sb_lock() and sb_unlock() calls from sb_reset_dsp() because the
latter is called from sb_setup() with the lock already held. Add a
call to sb_lockassert().
Surround the call to sb_reset_dsp() in sb16_attach() with sb_lock()
and sb_unlock() calls.
Tested by: Bartek Marcinkiewicz <junior AT p233.if.pwr.wroc.pl>
of you with other cards, please do review and test the drivers for
MP-safety and disable Giant in the interrupt routines when you are
sure of proper functionality.
because they bogusly check for defined(INTR_MPSAFE) -- something which
never was a #define. Correct the definitions.
This make INTR_TYPE_AV finally get used instead of the lower-priority
INTR_TYPE_TTY, so it's quite possible some improvement will be had
on sound driver performance. It would also make all the drivers
marked INTR_MPSAFE actually run without Giant (which does seem to
work for me), but:
INTR_MPSAFE HAS BEEN REMOVED FROM EVERY SOUND DRIVER!
It needs to be re-added on a case-by-case basis since there is no one
who will vouch for which sound drivers, if any, willy actually operate
correctly without Giant, since there hasn't been testing because of
this bug disabling INTR_MPSAFE.
Found by: "Yuriy Tsibizov" <Yuriy.Tsibizov@gfk.ru>
read-only. Need to enable "legacy support", by poking
into pci config space. (comment from the patch)
Submited by: Autrijus Tang <autrijus@autrijus.org>
Approved by: tanimura (mentor)
This change has not been tested.
This change was triggered by a gcc(1) warning on ia64 at -O2. The
variable v was not used after being computed, which resulted in enough
dead code elimination (DCE) to confuse the compiler and emit a bogus
warning about the use of the variable i without prior definition. The
variable i is the loop variable.
Submitted by: des
Responsibility: marcel
rid of the MTX_DUPOK flag on channel mutexes, which allows witness to
do a better job of lock order checking. Nuke snd_chnmtxcreate() since
it is no longer needed.
Tested by: matk
channel at a time unless it is actually necessary to lock both.
This avoids problems with lock order reversal and malloc() calls
with a mutex held when lower level code unlocks a channel, calls malloc(),
and relocks the channel. This also avoids the cost of some unnecessary
locking and unlocking.
Tested by: matk
Remove the unused second argument from udev2dev().
Convert all remaining users of makedev() to use udev2dev(). The
semantic difference is that udev2dev() will only locate a pre-existing
dev_t, it will not line makedev() create a new one.
Apart from the tiny well controlled windown in D_PSEUDO drivers,
there should no longer be any "anonymous" dev_t's in the system
now, only dev_t's created with make_dev() and make_dev_alias()
Introduce d_version field in struct cdevsw, this must always be
initialized to D_VERSION.
Flip sense of D_NOGIANT flag to D_NEEDGIANT, this involves removing
four D_NOGIANT flags and adding 145 D_NEEDGIANT flags.
panic() so that the buffer overflow just beyond this point is always
caught, even when the code is not compiled with INVARIANTS.
Change chn_setblocksize() buffer reallocation code to attempt to avoid
the feed_vchan16() buffer overflow by attempting to always keep the
bufsoft buffer at least as large as the bufhard buffer.
Print a diagnositic message
Danger! %s bufsoft size increasing from %d to %d after CHANNEL_SETBLOCKSIZE()
if our best attempts fail. If feed_vchan16() were to be called by
the interrupt handler while locks are dropped in chn_setblocksize()
to increase the size bufsoft to match the size of bufhard, the panic()
code in feed_vchan16() will be triggered. If the diagnostic message
is printed, it is a warning that a panic is possible if the system
were to see events in an "unlucky" order.
Change the locking code to avoid the need for MTX_RECURSIVE mutexes.
Add the MTX_DUPOK option to the channel mutexes and change the locking
sequence to always lock the parent channel before its children to avoid
the possibility of deadlock.
Actually implement locking assertions for the channel mutexes and fix
the problems found by the resulting assertion violations.
Clean up the locking code in dsp_ioctl().
Allocate the channel buffers using the malloc() M_WAITOK option instead
of M_NOWAIT so that buffer allocation won't fail. Drop locks across
the malloc() calls.
Add/modify KASSERTS() in attempt to detect problems early.
Abuse layering by adding a pointer to the snd_dbuf structure that points
back to the pcm_channel that owns it. This allows sndbuf_resize() to do
proper locking without having to change the its API, which is used by
the hardware drivers.
Don't dereference a NULL pointer when setting hw.snd.maxautovchans
if a hardware driver is not loaded. Noticed by Ryan Sommers
<ryans at gamersimpact.com>.
Tested by: Stefan Ehmann <shoesoft AT gmx.net>
Tested by: matk (Mathew Kanner)
Tested by: Gordon Bergling <gbergling AT 0xfce3.net>
device that doesn't exists. I'm using my discretion and
committing without mentor approval since Seigo is away.
Noticed by: Maxime Henrion <mux@freebsd.org>
This takes us a lot closer to refcounting dev_t.
This patch originally by cg@ with a few minor changes by me.
It is largely untested, but has been HEADSUP'ed twice, so presumably
people have not found any issues with it.
Submitted by: cg@
I started with a year-old patch by Orlando Bassotto
<orlando.bassotto@ieo-research.it>, and ported it to 5.2-CURRENT along with
fixing the problems working with pre-Audigy cards.
dsp_open: rearrange to only hold one lock at a time
dsp_close: ditto
mixer_hwvol_init: delete locking, the only consumer seems to
be the ess driver and it only call it a creation time, I
think the device will be stable across the sleepable malloc.
cmi interrupt routine: Release locks while caller chn_intr,
either this or do what emu10k1 does which is have no locks
at in the interrupt handler.
Submitted by: mat@cnd.mcgill.ca
thread being waken up. The thread waken up can run at a priority as
high as after tsleep().
- Replace selwakeup()s with selwakeuppri()s and pass appropriate
priorities.
- Add cv_broadcastpri() which raises the priority of the broadcast
threads. Used by selwakeuppri() if collision occurs.
Not objected in: -arch, -current
