to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
and newer CPUs (including Core 2 and Core / Core 2 based Xeons). The
driver attaches to each cpu device and creates a sysctl node in that
device's sysctl context (dev.cpu.N.temperature). When invoked, the
handler binds to the appropriate CPU to ensure a correct reading.
Submitted by: Rui Paulo <rpaulo@fnop.net>
Sponsored by: Google Summer of Code 2007
Tested by: des, marcus, Constantine A. Murenin, Ian FREISLICH
Approved by: re (kensmith)
MFC after: 3 weeks
included man pages on how to use it. This code is still somewhat experimental
but has been successfully tested on a number of targets. Many thanks to
Danny for contributing this.
Approved by: re
- Add custom .c wrappers for the firmware, rather than the standard
firmware(9) generated firmware objects to work around toolchain
problems on ia64 involving linking objects produced by
ld -b -binary into the kernel.
- Move from using Myricom's ".dat" firmware blobs to using Myricom's
zlib compressed ".h" firmware header files. This is done to
facilitate the custom wrappers, and saves a fair amount of wired
memory in the case where the firmware is built in, or preloaded.
- Fix two compile issues in mxge which only appear on non-i386/amd64.
Reviewed by: mlaier, mav (earlier version with just zlib support)
Glanced at by: sam
Approved by: re (kensmith)
NET_NEEDS_GIANT, which will shortly be removed. This is done in a
away that it may be easily reattached to the build before 7.1 if
appropriate locking is added. Specifics:
- Don't install netatm include files
- Disconnect netatm command line management tools
- Don't build libatm
- Don't include ATM parts in rescue or sysinstall
- Don't install sample configuration files and documents
- Don't build kernel support as a module or in NOTES
- Don't build netgraph wrapper nodes for netatm
This removes the last remaining consumer of NET_NEEDS_GIANT.
Reviewed by: harti
Discussed with: bz, bms
Approved by: re (kensmith)
by removing files from src/sys/coda, and updating include paths in the
new location, kernel configuration, and Makefiles. In one case add
$FreeBSD$.
Discussed with: anderson, Jan Harkes <jaharkes@cs.cmu.edu>
Approved by: re (kensmith)
Repo-copy madness: simon
- Remove unnecessary NULL checks after M_WAITOK allocations.
- Use VOP_ACCESS instead of hand-rolled suser_cred()
calls. [1]
- Use malloc(9) KPI to allocate memory for string. The
optimization taken from NetBSD is not valid for FreeBSD
because our malloc(9) already act that way. [2]
Requested by: rwatson [1]
Submitted by: Howard Su [2]
Approved by: re (tmpfs blanket)
around to force the IO port to a fixed address. They were only turned
on in the module build and were present since the original import. This
breaks soft power-off on the Asus A7V since it reprograms the SMBus base
address to a different one than the BIOS expects. A similar issue was
found in the alpm(4) module build.
PR: kern/113986, i386/97468
MFC after: 3 days
Approved by: re
when 'make obj' was done first. I found this when fixing
a problem reported by tinderbox, but forgot to send the
patchset to re@ altogether.
Approved by: re (kensmith)
Please note that, this is currently considered as an
experimental feature so there could be some rough
edges. Consult http://wiki.freebsd.org/TMPFS for
more information.
For now, connect tmpfs to build on i386 and amd64
architectures only. Please let us know if you have
success with other platforms.
This work was developed by Julio M. Merino Vidal
for NetBSD as a SoC project; Rohit Jalan ported it
from NetBSD to FreeBSD. Howard Su and Glen Leeder
are worked on it to continue this effort.
Obtained from: NetBSD via p4
Submitted by: Howard Su (with some minor changes)
Approved by: re (kensmith)
- update to firmware version 4.1.0
- switch over to standard method for initializing cdevs (contributed by scottl@)
- break out timer_reclaim_task to be per-port
- move msix teardown into separate function
- fix bus_setup_intr for msi-x for the multi-port case so that msi-x resources
are not corrupted on unload
- handle 10/100/1000 base-T media and auto negotiation
- bind qset to cpu even for singleq case
- white space cleanups
- remove recursive PORT_LOCK
- move mtu setting to separate function
- stop and re-init port when changing mtu
- replace all direct references to m_data with calls to mtod
- handle attach failure better by not trying to de-initialize
taskqueues when they have not been allocated
- no longer default to jumbo frames
Sponsored by: Chelsio
MFC after: 3 days
- Add and document the KVM and KVM_SUPPORT options that
are needed for the ifmcstats(3) makefile
- Garbage collect unused variables
- Add missing inclusion of bsd.own.mk where needed
Approved by: kan (mentor)
Reviewed by: ru
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
builds had been succeeding if run serially but could fail if run in
parallel because the bge module build might start before ofw_bus_if.h
got created as part of the mainline kernel build.
Diagnosis and patch by: ru
implementing some of them using existing ones.
- Allow to compile ZFS on all archs and use atomic operations surrounded
by global mutex on archs we don't have or can't have all atomic
operations needed by ZFS.
- Rework the entire pcm_channel structure:
* Remove rarely used link placeholder, instead, make each pcm_channel
as head/link of each own/each other. Unlock - Lock sequence due to
sleep malloc has been reduced.
* Implement "busy" queue which will contain list of busy/active
channels. This greatly reduce locking contention for example while
servicing interrupt for hardware with many channels or when virtual
channels reach its 256 peak channels.
- So I heard you like v chan ... O RLY?
Welcome to Virtual **Record** Channels (vrec, rec vchans, vchans for
recording, Rec-Chan, you decide), the ultimate solutions for your
nagging O_RDWR full-duplex wannabe (note: flash plugins) monopolizing
single record channel causing EBUSY. Vrec works exactly like Vchans
(or, should I rename it to "Vplay" :) , except that it operates on the
opposite direction (recording). Up to 256 vrecs (like vchans) are
possible.
Notes:
* Relocate dev.pcm.%d.{vchans,vchanformat,vchanrate} to each of its
respective node/direction:
dev.pcm.%d.play.* for "play" (cdev = dsp%d.vp%d)
dev.pcm.%d.rec.* for "record" (cdev = dsp%d.vr%d)
* Don't expect that it will magically give you ability to split
"recording source" (eg: 1 channel for cdrom, 1 channel for mic,
etc). Just admit that you only have a *single* recording source /
channel. Please bug your hardware vendor instead :)
- Bump maxautovchans from 4 to 16. For a full-fledged multimedia
desktop/workstation with too many soundservers installed (esound,
artsd, jackd, pulse/polypaudio, ding-dong pling plong mudkip fuh fuh,
etc), 4 seems inadequate. There will be no memory penalty here, since
virtual channels are allocate only by demand.
- Nuke/Rework the entire statically created cdev entries. Everything is
clonable through snd own clone manager which designed to withstand many
kind of abusive devfs droids such as:
* while : ; do /bin/test -e /dev/dsp ; done
* jot 16777216 0 | while read x ; do ls /dev/dsp0.$x ; done
* hundreds (could be thousands) concurrent threads/process opening
"/dev/dsp" (previously, this might result EBUSY even with just
3 contesting threads/procs).
o Reusable clone objects (instead of creating new one like there's no
tomorrow) after certain expiration deadline. The clone allocator will
decide whether to reuse, share, or creating new clone.
o Automatic garbage collector.
- Dynamic unit magic allocator. Maximum attached soundcards can be tuned
using tunable "hw.snd.maxunit" (Default to 512). Minimum is 16, and
maximum is 2048.
- ..other fixes, mostly related to concurrency issues.
joel@ will do the manpage updates on sound(4).
Have fun.
- upgrade to reflect state of 1.0.0.86
- move from firmware rev 3.2 to 4.0.0
- import driver bits for offload functionality
- remove binary distribution clause from top level files as it
runs counter to the intent of purely supporting the hardware
MFC after: 3 days
Implement all futex atomic operations in assembler to not depend on the
fuword() that does not allow to distinguish between -1 and failure return.
Correctly return 0 from atomic operations on success.
In collaboration with: rdivacky
Tested by: Scot Hetzel <swhetzel gmail com>, Milos Vyletel <mvyletel mzm cz>
Sponsored by: Google SoC 2007
This patch does the following:
- Remove un-necessary code that is not even compiling into the driver
under TW_OSL_NON_DMA_MEM_ALLOC_PER_REQUEST defines.
- Remove bundled firmware image and associated "files" entry for tw_cl_fwimg.c
- Remove bundled firmware flashing routines. We now have tw_update userspace
FreeBSD controller flash utility.
- Fix driver crash on load due to shared interrupt.
- Fix 2 lock leaks for Giant lock.
- Fix CCB leak.
- Add support for 9650SE controllers.
Many thanks to 3Ware/AMCC for continuing to support FreeBSD.
