in struct bio. Eventually, bio_offset will probably obsolete the
bio_blkno and bio_pblkno fields.
Remove the special hack in atapi-cd.c to determine of bio_offset was valid.
that seems to be working (I have a MF card that has a 336 modem and
ethernet that the probe routine finds, but the attach fails on because
pccardd doesn't do what you'd like with MF cards all the time).
Removed NETBSDTX spares.
Renamed a load of functions - specifcally
start -> tx
init has download, sj and assoc as sub-functions
report_params and update params move to repparams/upparams
Tidied up old #define's
Got rid of old DPRINTF, made printf's RAY_PRINTF and panic's RAY_PANIC
All code KNF
Removed checking the ECF_TO_HOST area in ray_init - this gets hosed
when someone updates/read a parameter from the card so causes
unneeded grief. This required moving the tib check into ray_attach.
Changed handling of interface flags in ioctl so that promiscous mode
changes are only done as needed.
Sequences of comq entries can be added to an array and automatically
dealt with - used in ray_init_user and others.
Moved IFF_RUNNING checks from the comq commands to com_runq - still
not sure what to do so we PANIC - will be fixed.
ray_sj now checks to see if any of the parameters it can update can be
updated.
ray_sj_done now updates parameters to the current n/w set if we changed
them earlier. I was being a bit thick in earlier comments as to why this
check was done - the ECF never changes the parameters.
Assocication with APs is handled outside of ray_sj - need to add
WEP stuff if I ever get my hands on an AP.
ray_stop, ray_unload and ray_reset are currently broken - reset isn't used anyway.
ray_tx_XXX and ray_rx only have cosmetic changes.
Interrupt handler now gets command out of ccs. This is so ray_intr_ccs and
ray_intr_rcs don't need to remap CM (I'm trying to roll things up a bit as
it must be slowing us down).
ray_intr_ccs just vectors commands to functions or error checks - a
jump table could replace it in ray_intr.
Ditto for ray_intr_rcs.
mcast is currently broken - I need to do more work for ALLMULTI etc. This is reasonably easy to fix becuase of the comq array stuff.
Added a few more checks into repparams so that it is firmware version aware. It also uses the new comq framework.
Parameter updating is also much better with the update parameter return routine re-worked.
Added a couple of runq entry helper functions - one that malloc's a new
entry and fills it in with sensible defaults and another that adds and
runs a seqencue of entries.
booting on a RAID volume.
- Change 'id_foo' and 'idfoo' to 'idad_foo' and 'idadfoo'. This makes
names more consistent with the devices that the code belongs to (more
in line with the style used in the amr/mlx driver.)
Reviewed by: jlemon
- Break out the support for the XMAC II's PHY into an miibus driver.
- Reorganize the probe/attach stuff using newbus. Each XMAC is now
attached to the parent GEnesis controller using newbus. This is
necessary since each XMAC must also have an attached miibus, and
the miibus read/write register routines need to be able to get
at the softc struct for each XMAC, not the one for the parent
controller. This allows me to get rid of the grotty code I added
for selecting the unit numbers for the ifnet interfaces: the unit
numbers are now derived from the newbus-assigned unit numbers,
which should track with the ifnet interface numbers. I think.
At the very least, there should never be any collisions.
- Add support for the SK-9821 and SK-9822 1000baseTX adapters. Special
thanks to SysKonnect for loaning me two adapters for testing.
Working download and start/join network. What's nice is that I didn't touch
TX or RX code at all.
Not fully done yet - stubs for assoc, cast, promisc and user param updating. I
can't work out the "nicest" way to get the mcast and promisc interactions
sorted without needing to abort runq commands half way through. And, as
mcast/promisc used elsewhere I want to get this right.
Other stuff
Fancy new debugging with __FUNCTION__ and __LINE__.
Lots of panic's inserted until I check some stuff out.
Removed all of the old scheduler.
Removed start join timeout as I don't need it.
Removed the promiscuous broadcast code that waas ifdef'd out.
New CCS allocation
where we can have targets (based on topology).
Much more importantly, make sure all mods to isp_sendmarker or |= so
we don't lose the marking of a bus that needs to have a marker sent for it.
require full logins after a LIP, which always led to loop resets, and
various other perturbations.
Update 2200 f/w from 2.01.00 release to 2.01.09 release.
- Free resources in all the possible attachment failure cases.
One critical bugfix:
- Fix a race where it was possible to get out of synch with the log
messages from the controller, if the controller hung up for any
period of time (eg. while resetting a SCSI bus). This would result
in an endless string of console errors, bringing the machine to a
halt.
o Modify xe driver to use this.
There's still some issues with this code, so xe can't map the cis just
yet. I'm thinking about how to resolve the issue. pccard_nbk's
pccard_alloc_resource is getting in the way.
I've done this by having requests to allocate memory propigate up the
tree. We'll see how well this works and reevaluate if it isn't
working well. Also initialize ptr in the tuple. As well as minor
reorg of memory allocation. Likely need to do similar things for I/O
when the time comes.
I've move all defines from pccardchip.h into pccardvar.h and
eliminated pccardchip.h.
source address when receiving frames (and keep using address 2 when in
pseudo-IBSS mode). This is apparently necessary in order to obtain the
true MAC address of the sending station which is needed for PPPoE.
Patch supplied by: Blaz Zupan <blaz@amis.net>
multi-firmware support. This patch just changes
numerous names in the driver sources and is actually
nilpotent. This has been checked by comparing the
generated assembly code.
The names that have been changed are related to the
script names. They were named `script' and `script H'.
They are now named respectively `script A' and
`script B'.
before I rip out the scheduler - whilst v. nice 'n all, it is doing the
wrong job. We need something that sends commands to the card atomically
so dhcp etc. works right.
I've renamed and moved a lot of the scheduler code so that it is all
in one place and all starts with ray_cmd_
ray_stop has some debugging crap left in - to be deleted rsn
