These firmwares were obtained from the "Chelsio T5/T4 Unified Wire
v2.12.0.3 for Linux" release. Changes since 1.14.4.0 (which is the
firmware in -STABLE branches) are in the "Release Notes" accompanying
the Unified Wire release and are copy-pasted here as well.
22.1. T5 Firmware
+++++++++++++++++++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where the default ingress
queue was ignored.
- Fixed an issue where adapter failed to load fw by adjusting DRAM frequency.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Fixed 40G link failures with some switches when auto-negotiation enabled.
- Fixed to improve on link bring-up time.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where bogus d3hot bits were set causing traffic stall.
- Fixed an issue where sometimes adapter was not seen after reboot.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
- Fixed an issue where link failed to come up after removing twinax cable and
inserting optical module.
ETH
- Fixed a link flap issue on T580-CR.
OFLD
- Fixed a potential iSCSI data corruption issue by disabling RxFragEn flag.
FOiSCSI
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP was not been provisioned yet and driver tried to
use given inerface.
- Fixed an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host. (DCBX CEE)
- Fixed an issue where apply bit set for APP id was affecting the ETS and PFC
settings.(DCBX IEEE)
- Fixed an issue where app priority values are not handled correctly in fw.
(DCBX IEEE)
- Fixed an issue where enable/disable dcbx can cause crash. (DCBX CEE,DCBX IEEE)
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added new interface to program DCA settings in SGE contexts; allow 32-byte
IQE size
- Added PTP interface fw_ptp_ts to support PTP Frequeny and Offset adjustment.
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
OFLD:
- WR opcode is returned to host in cqe error response.
22.2. T4 Firmware
+++++++++++++++++
Version : 1.15.37.0
Date : 04/27/2016
================================================================================
FIXES
-----
BASE:
- Fixed an issue in FW_RSS_VI_CONFIG_CMD handling where default ingress queue
was ignored.
- Fixed an issue in watchdog which was causing VM bring-up failure after reboot.
- Per port buffer groups size doubled to improve performance.
- Fixed an issue where iWARP was crashing in conjunction with traffic management.
FOiSCSI:
- Fixed an issue in recovery path where connection was getting closed before
recovery processing was done.
- Fixed an issue in TCP port reuse.
- Fixed an issue in recovery path when large number (>64) of iSCSI connections
were in use.
- Returned ENETUNREACH if IP had not been provisioned yet and driver tried to
use given inerface.
DCBX
- Fixed an issue where iscsi tlv is sent incorrectly to host.(DCBX CEE)
- Fixed an issue where enable/disable dcbx can cause crash in firmware.(DCBX CEE)
FOiSCSI
- Fixes an issue where fw was sending ENETUNREACH event for normal tcp
disconnection.
FOFCoE
- Removed BB6 support.
ENHANCEMENTS
------------
BASE:
- Added MPS raw interface.
ETH:
- New mailbox command FW_DCB_IEEE_CMD api added for IEEE dcbx.
================================================================================
Obtained from: Chelsio Communications
MFC after: 6 weeks
Relnotes: yes
Sponsored by: Chelsio Communications
gpiokey driver implements functional subset of gpiokeys device-tree bindings:
https://www.kernel.org/doc/Documentation/devicetree/bindings/input/gpio-keys.txt
It acts as a virtual keyboard, so keys are visible through kbdmux(4)
Driver maps linux scancodes for most common keys to FreeBSD scancodes and
also extends spec by introducing freebsd,code property to specify
FreeBSD-native scancodes.
Reviewed by: mmel, jmcneill
Differential Revision: https://reviews.freebsd.org/D6279
legacy siba sentry5 cpu glue.
The siba_cc code is the hard-coded chipcommon bits for the sentry s5,
which will eventually be replaced with the more flexible bhnd sipa/cc
code.
bwn, etc uses siba_bwn, which doesn't use siba or siba_cc to do anything.
Turns out that ye olde siba.c is /just/ the siba mips code (used by
the initial SENTRY5 port. However, I don't think it was ever
finished enough to be useful, and I do have this nagging feeling
that we'll eventually replace it with the bhnd code.
But, since bhnd(4) introduced siba.c too, we ended up with a
source file name clash, and that broke the SENTRY5 build.
It /looks/ like this is the only place siba.c / device siba is
used.
Trim the leading directory of a firmware source file from the resulting
target object file name so the object file is stored in the object
directory. Previously, using 'FIRMWS= /path/to/fw.bin:fw.bin' would
store the generated 'fw.bin.fwo' file in the /path/to directory. Now
it stores it in the object directory of the kernel module being built.
Reviewed by: bdrewery
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D6285
This adds support for the NVRAM handling and the basic SPROM
hardware used on siba(4) and bcma(4) devices, including:
* SPROM directly attached to the PCI core, accessible via PCI configuration
space.
* SPROM attached to later ChipCommon cores.
* SPROM variables vended from the parent SoC bus (e.g. via a directly-attached
flash device).
Additional improvements to the NVRAM/SPROM interface will
be required, but this changeset stands alone as working
checkpoint.
Submitted by: Landon Fuller <landonf@landonf.org>
Reviewed by: Michael Zhilin <mizkha@gmail.com> (Broadcom MIPS support)
Differential Revision: https://reviews.freebsd.org/D6196
PCI-express HotPlug support is implemented via bits in the slot
registers of the PCI-express capability of the downstream port along
with an interrupt that triggers when bits in the slot status register
change.
This is implemented for FreeBSD by adding HotPlug support to the
PCI-PCI bridge driver which attaches to the virtual PCI-PCI bridges
representing downstream ports on HotPlug slots. The PCI-PCI bridge
driver registers an interrupt handler to receive HotPlug events. It
also uses the slot registers to determine the current HotPlug state
and drive an internal HotPlug state machine. For simplicty of
implementation, the PCI-PCI bridge device detaches and deletes the
child PCI device when a card is removed from a slot and creates and
attaches a PCI child device when a card is inserted into the slot.
The PCI-PCI bridge driver provides a bus_child_present which claims
that child devices are present on HotPlug-capable slots only when a
card is inserted. Rather than requiring a timeout in the RC for
config accesses to not-present children, the pcib_read/write_config
methods fail all requests when a card is not present (or not yet
ready).
These changes include support for various optional HotPlug
capabilities such as a power controller, mechanical latch,
electro-mechanical interlock, indicators, and an attention button.
It also includes support for devices which require waiting for
command completion events before initiating a subsequent HotPlug
command. However, it has only been tested on ExpressCard systems
which support surprise removal and have none of these optional
capabilities.
PCI-express HotPlug support is conditional on the PCI_HP option
which is enabled by default on arm64, x86, and powerpc.
Reviewed by: adrian, imp, vangyzen (older versions)
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D6136
Clocks, GPIO, UART, SD card / eMMC, USB, watchdog, and ethernet are
supported. Note that the A83T contains two clusters of four Cortex-A7
CPUs, and only CPUs in first cluster are started for now.
Tested on a Sinovoip Banana Pi BPI-M3.
This is an initial work in progress to use the replacement bhnd
bus code for devices which support it.
* Add manpage updates for bhnd, bhndb, siba
* Add kernel options for bhnd, bhndbus, etc
* Add initial support in if_bwn_pci / if_bwn_mac for using bhnd
as the bus transport for suppoted NICs
* if_bwn_pci will eventually be the PCI bus glue to interface to bwn,
which will use the right backend bus to attach to, versus direct
nexus/bhnd attachments (as found in embedded broadcom devices.)
The PCI glue defaults to probing at a lower level than the bwn glue,
so bwn should still attach as per normal without a boot time tunable set.
It's also not fully fleshed out - the bwn probe/attach code needs to be
broken out into platform and bus specific things (just like ath, ath_pci,
ath_ahb) before we can shift the driver over to using this.
Tested:
* BCM4311, STA mode
* BCM4312, STA mode
Submitted by: Landon Fuller <landonf@landonf.org>
Differential Revision: https://reviews.freebsd.org/D6191
* Break out the 'g' phy code;
* Break out the debugging bits into a separate source file, since
some debugging prints are done in the phy code;
* Make some more chip methods in if_bwn.c public.
This brings the size of if_bwn.c down to 6,805 lines which is now
approaching managable.
This (and eventually migrating the other PHY code out) is in preparation
for adding the 11n PHY. No, the 11ac PHY (for the BCM4260 softmac part) isn't
yet open source, so we can't grow that. Yet.
This trims ~3,700 lines of code from if_bwn.c, bringing it down to a slightly
less crazy sounding 10,446 lines of code.
implementations. Early in the boot the kernel will use an approximate,
however after the timer has been probed it will switch to a more accurate
implementation.
Reviewed by: manu
Sponsored by: ABT Systems Ltd
Differential Revision: https://reviews.freebsd.org/D5762
There is no need to clear all the DDR memory (we only need to clear
BSS section).
I was playing with non-default version of hardware (the bitfile
synthesized for 4-level page memory system) and clearing was helpful,
but then realized support for 4-level page system is untested/broken
in both RocketCore and lowRISC.
The additional regex replacements are actully required due to an
elfcopy bug which is now fixed (by r298361), not a Clang/GCC issue.
Sponsored by: The FreeBSD Foundation
Newest CLANG objcpy uses different name parsing.
Modify regexp to match (i.e. avoid substitution
of "/" or "-" with "_").
Obtained from: Semihalf
Sponsored by: Juniper Networks
Reviewed by: hselasky, zbb
Differential Revision: https://reviews.freebsd.org/D5873
fdt_static_dtb.S dependency in sys/conf/files is currently set as:
$S/boot/fdt/dts/${MACHINE}/${FDT_DTS_FILE}
This is wrong, as what fdt_static_dtb.S actually uses is the DTB file
produced from the FDT_DTS_FILE.
In addition it also makes using DTS files stored in $S/gnu/dts/${MACHINE}/
impossible.
So, change the dependency to "fdt_dtb_file", which seems to be the right
option here anyway.
Approved by: adrian (mentor)
Sponsored by: Smartcom - Bulgaria AD
Differential Revision: https://reviews.freebsd.org/D5963
Submitted by: Jun Su <junsu microsoft com>
Reviewed by: jhb, kib, sephe
Sponsored by: Microsoft OSTC
Differential Revision: https://reviews.freebsd.org/D5910
It allows implementing loadable kernel modules with new actions and
without needing to modify kernel headers and ipfw(8). The module
registers its action handler and keyword string, that will be used
as action name. Using generic syntax user can add rules with this
action. Also ipfw(8) can be easily modified to extend basic syntax
for external actions, that become a part base system.
Sample modules will coming soon.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
as before. The common scheduling bits have moved from inline code in
each of the CAM periph drivers into a library that implements the
default scheduling.
In addition, a number of rate-limiting and I/O preference options can
be enabled by adding CAM_IOSCHED_NETFLIX to your config file. A number
of extra stats are also maintained. CAM_IOSCHED_NETFLIX isn't on by
default because it uses a separate BIO_READ and BIO_WRITE queue, so
doesn't honor BIO_ORDERED between these two types of operations. We
already didn't honor it for BIO_DELETE, and we don't depend on
BIO_ORDERED between reads and writes anywhere in the system (it is
currently used with BIO_FLUSH in ZFS to make sure some writes are
complete before others start and as a poor-man's soft dependency in
one place in UFS where we won't be issuing READs until after the
operation completes). However, out of an abundance of caution, it
isn't enabled by default.
Plus, this also brings in NCQ TRIM support for those SSDs that support
it. A black list is also provided for known rogues that use NCQ trim
as an excuse to corrupt the drive. It was difficult to separate out
into a separate commit.
This code has run in production at Netflix for over a year now.
Sponsored by: Netflix, Inc
Differential Revision: https://reviews.freebsd.org/D4609
VM_NUMA_ALLOC is used to enable use of domain-aware memory allocation in
the virtual memory system. DEVICE_NUMA is used to enable affinity
reporting for devices such as bus_get_domain().
MAXMEMDOM must still be set to a value greater than for any NUMA support
to be effective. Note that 'cpuset -gd' always works if MAXMEMDOM is
enabled and the system supports NUMA.
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D5782
This optimization attempts to utylize as wide as possible register store instructions to zero large buffers.
The implementation, if possible, will use 'dc zva' to zero buffer by cache lines.
Speedup: 60x faster memory zeroing
Submitted by: Dominik Ermel <der@semihalf.com>
Obtained from: Semihalf
Sponsored by: Cavium
Reviewed by: kib
Differential Revision: https://reviews.freebsd.org/D5726
separate driver. Add support for activating clock and hwreset resources
for these devices when the EXT_RESOURCES option is present.
Reviewed by: andrew, mmel, Emmanuel Vadot <manu@bidouilliste.com>
Approved by: adrian (mentor)
Differential Revision: https://reviews.freebsd.org/D5749
PowerPC has real Open Firmware and does not necessarily need FDT.
Make ofwpci.c only PCI dependent.
Pointed out by: emaste
Reviewed by: nwhitehorn
Obtained from: Semihalf
