uart(4) to support the Zilog 8530 SCCs which hang off of a FireHose
bus on Sun E4000/E5000 class machines.
Beside the fact that a puc_fhc.c would just be a copy of puc_sbus.c
with s,sbus,fhc,g the reason why the declaration for fhc(4) was
sticked into puc_sbus.c is that both of these front-ends for puc(4)
will go away once there is a scc(4).
Discussed with: marcel
Tested by: hrs, kris
MFC after: 3 days
both a scc(4) is under way and fhc(4) will be change to use INOs this
shouldn't stay in HEAD for too long but we need a MFC-able solution
for FreeBSD 5.4.
Discussed with: marcel
Tested by: hrs, kris
MFC after: 3 days
virtual COM port. This makes the use of the Dell OpenManage tools on FreeBSD
considerably easier, and is based on Chuck Cranor's original patch for 4.6.
Reviewed by: imp
Tested by: dpk at dpk dot net
MFC after: 1 week
to be the same as Boca Research Turbo Serial 654 (4 serial port).
While add the 8 port variants as well.
Submitted by: sten@blinkenlights.nl
PR: kern/75793
MFC after: 1 week
connects to the keyboard and mouse and needs some special treatment.
Until this is fully understood, implemented and tested, simply avoid
probing the second Z8530. This is also what the zs(4) driver does.
subset ("compatible", "device_type", "model" and "name") of the standard
properties in drivers for devices on Open Firmware supported busses. The
standard properties "reg", "interrupts" und "address" are not covered by
this interface because they are only of interest in the respective bridge
code. There's a remaining standard property "status" which is unclear how
to support properly but which also isn't used in FreeBSD at present.
This ofw_bus kobj-interface allows to replace the various (ebus_get_node(),
ofw_pci_get_node(), etc.) and partially inconsistent (central_get_type()
vs. sbus_get_device_type(), etc.) existing IVAR ones with a common one.
This in turn allows to simplify and remove code-duplication in drivers for
devices that can hang off of more than one OFW supported bus.
- Convert the sparc64 Central, EBus, FHC, PCI and SBus bus drivers and the
drivers for their children to use the ofw_bus kobj-interface. The IVAR-
interfaces of the Central, EBus and FHC are entirely replaced by this. The
PCI bus driver used its own kobj-interface and now also uses the ofw_bus
one. The IVARs special to the SBus, e.g. for retrieving the burst size,
remain.
Beware: this causes an ABI-breakage for modules of drivers which used the
IVAR-interfaces, i.e. esp(4), hme(4), isp(4) and uart(4), which need to be
recompiled.
The style-inconsistencies introduced in some of the bus drivers will be
fixed by tmm@ in a generic clean-up of the respective drivers later (he
requested to add the changes in the "new" style).
- Convert the powerpc MacIO bus driver and the drivers for its children to
use the ofw_bus kobj-interface. This invloves removing the IVARs related
to the "reg" property which were unused and a leftover from the NetBSD
origini of the code. There's no ABI-breakage caused by this because none
of these driver are currently built as modules.
There are other powerpc bus drivers which can be converted to the ofw_bus
kobj-interface, e.g. the PCI bus driver, which should be done together
with converting powerpc to use the OFW PCI code from sparc64.
- Make the SBus and FHC front-end of zs(4) and the sparc64 eeprom(4) take
advantage of the ofw_bus kobj-interface and simplify them a bit.
Reviewed by: grehan, tmm
Approved by: re (scottl)
Discussed with: tmm
Tested with: Sun AX1105, AXe, Ultra 2, Ultra 60; PPC cross-build on i386
of the struct, so that a placeholder for it (or unportable C99
initializers) are not needed for entries that don't use it. Use a C99
initializer for the 1 entry that uses it. Removed 91 placeholders.
This also restores API compatibility with NetBSD and RELENG_4 for most
entries.
Removed the requirement for a particular subvendor/subproduct in
rev.1.26 (VScom PCI-800L card). While the BARs, etc., may depend on
the sub-ids, this is not known to be so, and I think it is better to
guess that they don't. The decision to check sub-id checks in this
file is apparently random; for VScom cards they were checked in 3 of
8 cases.
Reviewed by: timeout by committer (joerg) after 6 months
and used by uart(4) for the channel conflicted with the port offset for
the Z8530. The Z8530 has the channels reversed (i.e. channel B is at
offset 0 and channel A is at offset 4). Assign the port offsets in the
right order so that uart(4) will properly attach to the channels.
Submitted by: Marius Strobl <marius@alchemy.franken.de>
this problem put these lines back in. While they should be
unnecessary, they appear to be sometimes necessary.
Reviewed in concept: dfr
Approved by: re (scottl@)
to the pci attachment. Cardbus is a derived class of pci so all pci
drivers are automatically available for matching against cardbus devices.
Reviewed by: imp
o Introduce PUC_PORT_TYPE_UART so that we can attach to uart(4),
o Introduce port sub-types (eg PUC_PORT_UART_NS8250, PUC_PORT_UART_Z8530)
to handle different hardware and determine resource sizes.
o Introduce two new IVARs: PUC_IVAR_SUBTYPE and PUC_IVAR_REGSHFT. Both
are used by uart(4) to get sufficient information to talk to the HW.
o Introduce PUC_FLAGS_ALTRES to tell puc(4) to try memory mapped I/O
if I/O port space cannot be allocated, or vice versa.
o Have ports of type PUC_PORT_TYPE_COM attach to uart(1) if attaching
to sio(4) fails (due to not having the sio driver).
o Put struct puc_device_description in struct puc_softc instead of
having a pointer to a device description in the softc. This allows
us to create device descriptions on the fly without having to use
malloc() or otherwise have them staticly defined.
o Move puc_find_description() from puc.c to puc_pci.c as it's specific
to PCI.
o Add EBUS and SBUS frontends for use on sparc64. Note that the P in
puc stands for PCI, so we kinda mess things up here. It's too soon
to worry about it though. We'll know what to do about it in time.
NOTE: This commit changes the behaviour of puc(4) to not quieten the
device probe and attach for child devices. The uart(4) driver provides
additional device description that is valuable to have.
- Add a new PCIM_HDRTYPE constant for the field in PCIR_HDRTYPE that holds
the header type.
- Replace several magic numbers with appropriate constants for the header
type register and a couple of PCI_FUNCMAX.
- Merge to amd64 the fix to the i386 bridge code to skip devices with
unknown header types.
Requested by: imp (1, 2)
