Try to support older systems reporting irq0 for the first channels.
Support sharing of the std interrupts (says peter :) )
Dont use READ_CD on normal data reads (2048 bytes), too many old drives
doesn't support this command even if the std says "shall" :(, but still
use READ_CD on all other blocksizes.
Add the geometry to the ad probe, its still usefull.
also broke diskless swapping. Moving the swapdev_vp initialization
to more commonly run code solves the problem.
PR: kern/16165
Additional testing by: David Gilbert <dgilbert@velocet.ca>
that there's sense to send with status (if the SIM does it), and
then clear any pending contingent allegiance state for this initiator
if the SIM actually did send the sense data.
Widen MAX_INITITATORS to 256- that's still not quite right, but will
accomodate the widest Fibre Channel support in FreeBSD now.
Obtained from:(partially) gibbs@freebsd.org
does ignore DCD. Even TIOCMGET cannot read DCD as the firmware doesn't
report it. This has pretty interesting effects for ppp(8) which runs
in clocal mode and polls carrier (!). (Specialix's linux driver does
this too)
Also update the firmware to 3.0.6 for the SX cards, as apparently there
was a problem with floating (disconnected) DCD pins causing stray carrier
transitions, especially at port open time.
It seems to work here, and carrier loss is detected nearly immediately
rather than having to wait for a LQR timeout (a few minutes) before ppp(8)
gives up.
DCD problem noted by: nsayer
despite having a non-null cn_tab entry. This case now works the same
as if there is no physical console, except i/o at the kernel printf
level may still work. This frees drivers of physical console drivers
from the responsibility of attaching the device no matter what.
for IPv4 communication.(IPv4 mapped IPv6 addr.)
Also removed IPv6 hoplimit initialization because it is alway done at
tcp_output.
Confirmed by: Bernd Walter <ticso@cicely5.cicely.de>
Dont be so verbose in the probe, only ONE line printed now, to get more
info boot verbose. Centralise most printf's in ata-all & ata-dma to use
the ata_printf function, it saves alot of codelines.
Repeat the identify command if drive fails the first.
Protect the timeout functions with splbio.
Dont update the transfer details before we are sure the transfer
succeded, this way they are proberly retried on errors.
Move the handling of next_writeable to userland.
Use the READ_CD command to read CD's. That enables us to read _anything_
via the normal read/write interface. This kindof obsoletes the READAUDIO
ioctl, but we keep that for now.
include this in all kernels. Declare some const *intrq_present
variables that can be checked by a module prior to using *intrq
to queue data.
Make the if_tun module capable of processing atm, ip, ip6, ipx,
natm and netatalk packets when TUNSIFHEAD is ioctl()d on.
Review not required by: freebsd-hackers
same object file (atapi-cd.o) as the ata drivers. I'd have called it
wcd.[ch], but there's already one of those in the Attic that we can't
clobber - the good names are taken.
Fix building so that it can be compiled into LINT alongside ata.
Requested by: bde
Update i2c code to build on FreeBSD 3.x and 4.x machines.
Added GPIO audio values for the Askey/Dynalink TV card talken from postings on the V4L mailing list.
Update Australian Channel Set. Submitted by John Birrell <jb@cimlogic.com.au>
Add new Channel Set for France. Submitted by Daniel Dagneaux <dagneaux@lure.u-psud.fr>
doesn't conflict with the parallel port on my miata (0x3bc..0x3bf).
The right solution will be to reserve two port ranges in vga, 0x3b0..0x3ba
and 0x3c0..0x3ca.
Reviewed by: yokota
o Cut out the probed stuff. We no longer need it since newbus implicitly
checks for this (likely bt can be changed as well in this way).
o Add preliminary support for unload. Untested because aha doesn't yet
support identify and there are some interactions with PnP that I've
not yet worked out.
With this I can boot the AHA-1542CP FW F.0. All the aha resources
appear to be picked up via pnp now.
The files were repo copied from their original location and are part
way towards being portable.
This should unbreak the EISA support in the driver.
I have not updated files* yet as I'm not quite finished.
