exported via PCI passthrough.
- Do not check for a specific physical function (PF) before claiming a device.
Different PFs have different device-ids so this check is redundant anyway.
- Obtain the PF# from the WHOAMI register instead of pci_get_function().
- Setup the memory windows using the real BAR0 address, not what the VM says it
is.
Obtained from: Chelsio Communications
not by some hint setting. Do more preparations for FC-Tape.
Clean up resource counting for 24XX or later chipsets so
we find out after EXEC_FIRMWARE what is actually supported.
Set target mode exchange count based upon whether or not
we are supporting simultaneous target/initiator mode. Clean
up some old (pre-24XX) xfwoption and zfwoption issues.
Sponsored by: Spectralogic
MFC after: 3 days
the assumption that ath_softc doesn't change size based on build time
configuration.
I picked up on this because suddenly radar stuff didn't work; and
although the ath_dfs code was setting sc_dodfs=1, the main ath driver
saw sc_dodfs=0.
So for now, include opt_ath.h in driver source files. This seems like
the sane thing to do anyway.
I'll have to do a pass over the code at some later stage and turn
the radiotap TX/RX structs into malloc'ed memory, rather than in-line
inside of ath_softc. I'd rather like to keep ath_softc the same
layout regardless of configuration parameters.
Pointy hat to: adrian
a buffer pointer.
For large radar pulses, the AR9130 and later will return a series of
FFT results for software processing. These can overflow a single 2KB
buffer on longer pulses. This would result in undefined buffer behaviour.
This includes a few new fields in each RXed frame:
* per chain RX RSSI (ctl and ext);
* current RX chainmask;
* EVM information;
* PHY error code;
* basic RX status bits (CRC error, PHY error, etc).
This is primarily to allow me to do some userland PHY error processing
for radar and spectral scan data. However since EVM and per-chain RSSI
is provided, others may find it useful for a variety of tasks.
The default is to not compile in the radiotap vendor extensions, primarily
because tcpdump doesn't seem to handle the particular vendor extension
layout I'm using, and I'd rather not break existing code out there that
may be (badly) parsing the radiotap data.
Instead, add the option 'ATH_ENABLE_RADIOTAP_VENDOR_EXT' to your kernel
configuration file to enable these options.
and the CRC error bits set. The radar payload is correct.
When this happens, the stack doesn't see them PHY error frames and
isn't interpreted as a PHY error. So, no radar detection and no radiotap
PHY error handling.
Now, this may introduce some weird issues if the MAC sends up some other
combination of CRC error + PHY error frames; this commit would break that
and mark them as PHY errors instead of CRC errors.
I may tinker with this a little more to pass radar/early radar/spectral
frames up as PHY errors if the CRC bit is set, to restore the previous
behaviour (where if CRC is set on a PHY error frame, it's marked as a CRC
error rather than PHY error.)
Tested on: AR5416, over the air, to a USRP N200 which is generating a
large number of a variety of radar pulses.
TODO: Test on AR9130, AR9160, AR9280 (and maybe radar pulses on
2GHz on AR9285/AR9287.)
PR: kern/169362
a da(4) instance going away while GEOM is still probing it.
In this case, the GEOM disk class instance has been created by
disk_create(), and the taste of the disk is queued in the GEOM
event queue.
While that event is queued, the da(4) instance goes away. When the
open call comes into the da(4) driver, it dereferences the freed
(but non-NULL) peripheral pointer provided by GEOM, which results
in a panic.
The solution is to add a callback to the GEOM disk code that is
called when all of its resources are cleaned up. This is
implemented inside GEOM by adding an optional callback that is
called when all consumers have detached from a provider, and the
provider is about to be deleted.
scsi_cd.c,
scsi_da.c: In the register routine for the cd(4) and da(4)
routines, acquire a reference to the CAM peripheral
instance just before we call disk_create().
Use the new GEOM disk d_gone() callback to register
a callback (dadiskgonecb()/cddiskgonecb()) that
decrements the peripheral reference count once GEOM
has finished cleaning up its resources.
In the cd(4) driver, clean up open and close
behavior slightly. GEOM makes sure we only get one
open() and one close call, so there is no need to
set an open flag and decrement the reference count
if we are not the first open.
In the cd(4) driver, use cam_periph_release_locked()
in a couple of error scenarios to avoid extra mutex
calls.
geom.h: Add a new, optional, providergone callback that
is called when a provider is about to be deleted.
geom_disk.h: Add a new d_gone() callback to the GEOM disk
interface.
Bump the DISK_VERSION to version 2. This probably
should have been done after a couple of previous
changes, especially the addition of the d_getattr()
callback.
geom_disk.c: Add a providergone callback for the disk class,
g_disk_providergone(), that calls the user's
d_gone() callback if it exists.
Bump the DISK_VERSION to 2.
geom_subr.c: In g_destroy_provider(), call the providergone
callback if it has been provided.
In g_new_geomf(), propagate the class's
providergone callback to the new geom instance.
blkfront.c: Callers of disk_create() are supposed to pass in
DISK_VERSION, not an explicit disk API version
number. Update the blkfront driver to do that.
disk.9: Update the disk(9) man page to include information
on the new d_gone() callback, as well as the
previously added d_getattr() callback, d_descr
field, and HBA PCI ID fields.
MFC after: 5 days
and CAM_LUN_INVALID for case of missing devices. In removes tons of error
messages from CAM during bus scans.
Reported and tested by: Mike Tancsa <mike@sentex.net>
MFC after: 3 days
- Stateful TCP offload drivers for Terminator 3 and 4 (T3 and T4) ASICs.
These are available as t3_tom and t4_tom modules that augment cxgb(4)
and cxgbe(4) respectively. The cxgb/cxgbe drivers continue to work as
usual with or without these extra features.
- iWARP driver for Terminator 3 ASIC (kernel verbs). T4 iWARP in the
works and will follow soon.
Build-tested with make universe.
30s overview
============
What interfaces support TCP offload? Look for TOE4 and/or TOE6 in the
capabilities of an interface:
# ifconfig -m | grep TOE
Enable/disable TCP offload on an interface (just like any other ifnet
capability):
# ifconfig cxgbe0 toe
# ifconfig cxgbe0 -toe
Which connections are offloaded? Look for toe4 and/or toe6 in the
output of netstat and sockstat:
# netstat -np tcp | grep toe
# sockstat -46c | grep toe
Reviewed by: bz, gnn
Sponsored by: Chelsio communications.
MFC after: ~3 months (after 9.1, and after ensuring MFC is feasible)
and crosschecks against firmware documentation. We now check and report
FC firmware attributes and at least are now prepared for the upper 48 bits
of f/w attributes (which are probably for the 8100 or later cards). This
involed changing how inbits and outbits are calculated for varios commands,
hopefully clearer and cleaner. This also caused me to clean up the actual
mailbox register usage. Finally, we are now unconditionally using a CRN
for initiator mode.
A longstanding issue with the 2400/2500 is that they do *not* support
a "Prefer PTP followed by loop", which explains why enabling that
caused the f/w to crash.
A slightly more invasive change is to let the firmware load entirely
drive whether multi_id support is enabled or not.
Sponsored by: Spectralogic
MFC after: 1 week
D2500CC which I have, syscons in text-mode fails to show the expected
contents due to write errors into video-memory.
At least one of the causes is that we copy from syscons internal buffer
to the video memory with optimized bcopy(9) which uses >16bit operations.
Until now, 32bit and wider operations have always worked on the video
memory, but since I cannot find a single source which says that this
SHALL work, and since these chipsets/bugs are now out there, this
commit changes syscons to always use 16bit copies on i386 & amd64.
This may be relevevant for PR's:
166262
166639
and various other bug reports floating elsewhere on the net, but
I lack hardware to test those.
Due to some differences in MSRs between Xeon Sandy Bridge and Core Sandy
Bridge (Model 0x2A), wrmsr() may generate in a GP# fault exception and so a
panic of the machine.
Approved by: gnn (mentor)
MFC after: 3 days
* Add an OS_A_REG_WRITE() routine - analog writes require a 100usec delay
on AR9280 and later, so create a method to do it.
* Use it for the AR9287 analog writes.
* Re-indent and style(9) the code.
This just requires a little HAL change (add a new config parameter) and
some glue in if_ath_pci.c, however I'm leaving this up for someone else
to do.
Obtained from: Qualcomm Atheros
interacts with some non-highpoint controollers. Change attach_generic to
be off by default.
PR: kern/168910
Submitted by: Richard Yao <ryao@gentoo.org>
Approved by: cperciva
No objections by: -hackers
Obtained from: Gentoo FreeBSD
MFC after: 2 weeks
* Use ATH_RC_NUM instead of '4' when iterating over the ratecontrol series
array.
* A few style(9) fixes, hopefully no regressions here.
* Add some comments that better describe what's going on.
The existing code tries to use the beacon miss timer to signal that the AP
has gone away. Unfortunately this doesn't seem to be behaving itself.
I'll try to investigate why this is for the sake of completeness.
The result is the STA will stay "associated" to the AP it was associated
with when it suspended. It never receives a bmiss notification so it
never tries reassociating.
PR: kern/169084
