- Log ICMP type during verbose output.
- Added IPFIREWALL_VERBOSE_LIMIT option to prevent denial of service
attacks via syslog flooding.
- Filter based on ICMP type.
- Timestamp chain entries when they are matched.
- Interfaces can now be matched with a wildcard specification (i.e.
will match any interface unit for a given name).
- Prevent the firewall chain from being manipulated when securelevel
is greater than 2.
- Fixed bug that allowed the default policy to be deleted.
- Ability to zero individual accounting entries.
- Remove definitions of old_chk_ptr and old_ctl_ptr when compiling
ipfw as a lkm.
- Remove some redundant code shared between ip_fw_init and ipfw_load.
Closes PRs: 1192, 1219, and 1267.
gcc only inlines memcpy()'s whose count is constant and didn't inline
these. I want memcpy() in the kernel go away so that it's obvious that
it doesn't need to be optimized. Now it is only used for one struct
copy in si.c.
circumstances, caused perfectly good connections to be dropped. This
happened for connections over a LAN, where the retransmit timer
calculation TCP_REXMTVAL(tp) returned 0. If sending was blocked by flow
control for long enough, the old code dropped the connection, even
though timely replies were being received for all window probes.
Reviewed by: W. Richard Stevens <rstevens@noao.edu>
unconventionally:
If COMPAT_IPFW is not defined, or if it is defined to 1, enable;
otherwise, disable.
This means that these changes actually have no effect on anyone at the
moment. (It just makes it easier for me to keep my code in sync.)
In the future, the `not defined' part of the hack should be eliminated,
but doing this now would require everyone to change their config files.
The same conditionals need to be made in ip_input.c as well for this to
ave any useful effect, but I'm not ready to do that right now.
(PR #1178).
Define a new SO_TIMESTAMP socket option for datagram sockets to return
packet-arrival timestamps as control information (PR #1179).
Submitted by: Louis Mamakos <loiue@TransSys.com>
the destination represents. For IP:
- Iff it is a host route, RTF_LOCAL and RTF_BROADCAST indicate local
(belongs to this host) and broadcast addresses, respectively.
- For all routes, RTF_MULTICAST is set if the destination is multicast.
The RTF_BROADCAST flag is used by ip_output() to eliminate a call to
in_broadcast() in a common case; this gives about 1% in our packet-generation
experiments. All three flags might be used (although they aren't now)
to determine whether a packet can be forwarded; a given host route can
represent a forwardable address if:
(rt->rt_flags & (RTF_HOST | RTF_LOCAL | RTF_BROADCAST | RTF_MULTICAST))
== RTF_HOST
Obviously, one still has to do all the work if a host route is not present,
but this code allows one to cache the results of such a lookup if rtalloc1()
is called without masking RTF_PRCLONING.
1) Require all callers to pass a valid route pointer to ip_output()
so that we don't have to check and allocate one off the stack
as was done before. This eliminates one test and some stack
bloat from the common (UDP and TCP) case.
2) Perform the IP header checksum in-line if it's of the usual length.
This results in about a 5% speed-up in my packet-generation test.
3) Use ip_vhl field rather than ip_v and ip_hl bitfields.
1) Set the persist timer to help time-out connections in the CLOSING state.
2) Honor the keep-alive timer in the CLOSING state.
This fixes problems with connections getting "stuck" due to incompletion
of the final connection shutdown which can be a BIG problem on busy WWW
servers.
common labels for LINT. There are still some common declarations for the
!KERNEL case in tcp_debug.h and spx_debug.h. trpt depends on the ones in
tcp_debug.h.
This fixes a panic that occurs when ifconfig ioctl(s) were interrupted
by IP traffic at the wrong time - resulting in a NULL pointer dereference.
This was originally noticed on a FreeBSD 1.0 system, but the problem still
exists in current sources.
keepalive on all tcp sessions. Setsockopt(2) cannot override this setting.
Maybe another one is needed that just changes the default for SO_KEEPALIVE ?
Requested by: Joe Greco <jgreco@brasil.moneng.mei.com>
Move ipip_input() and rsvp_input() prototypes to ip_var.h
Remove unused prototype for rip_ip_input() from ip_var.h
Remove unused variable *opts from rip_output()
Get rid of ac->ac_ipaddr and arpwhohas() since they assume that
an interface has only one address.
Obtained from: BSD/OS 2.1, via Rich Stevens <rstevens@noao.edu>
from Larry Peterson &co. at Arizona:
- Header prediction for ACKs did not exclude Fast Retransmit/Recovery.
- srtt calculation tended to get ``stuck'' and could never decrease
when below 8. It still can't, but the scaling factors are adjusted
so that this artifact does not cause as bad an effect on the RTO
value as it used to.
The paper also points out the incr/8 error that has been long since fixed,
and the problems with ACKing frequency resulting from the use of options
which I suspect to be fixed already as well (as part of the T/TCP work).
Obtained from: Brakmo & Peterson, ``Performance Problems in BSD4.4 TCP''
between ignoring options specified in the setsockopt call if IP_HDRINCL is set
(the UCB choice when VJ's code was brought in) vs allowing them (what everyone
else did, and what is assumed by programs everywhere...sigh).
Also perform some checking of the passed down packet to avoid running off
the end of a mbuf chain.
Reviewed by: fenner
Make a copy of the header of a packet that gets queued due to
lack of forwarding cache entry, so that nobody else can step
on it. Thanks to Mike Karels <karels@bsdi.com> for pointing
this one out.
Close the ip-fragment hole.
Waste less memory.
Rewrite to contemporary more readable style.
Kill separate IPACCT facility, use "accept" rules in IPFIREWALL.
Filter incoming >and< outgoing packets.
Replace "policy" by sticky "deny all" rule.
Rules have numbers used for ordering and deletion.
Remove "rerorder" code entirely.
Count packet & bytecount matches for rules.
Code in -current & -stable is now the same.
systems (my last change did not mix well with some firewall
configurations). As much as I dislike firewalls, this is one thing I
I was not prepared to break by default.. :-)
Allow the user to nominate one of three ranges of port numbers as
candidates for selecting a local address to replace a zero port number.
The ranges are selected via a setsockopt(s, IPPROTO_IP, IP_PORTRANGE, &arg)
call. The three ranges are: default, high (to bypass firewalls) and
low (to get a port below 1024).
The default and high port ranges are sysctl settable under sysctl
net.inet.ip.portrange.*
This code also fixes a potential deadlock if the system accidently ran out
of local port addresses. It'd drop into an infinite while loop.
The secure port selection (for root) should reduce overheads and increase
reliability of rlogin/rlogind/rsh/rshd if they are modified to take
advantage of it.
Partly suggested by: pst
Reviewed by: wollman
when a connection enters the ESTBLS state using T/TCP, then window
scaling wasn't properly handled. The fix is twofold.
1) When the 3WHS completes, make sure that we update our window
scaling state variables.
2) When setting the `virtual advertized window', then make sure
that we do not try to offer a window that is larger than the maximum
window without scaling (TCP_MAXWIN).
Reviewed by: davidg
Reported by: Jerry Chen <chen@Ipsilon.COM>
to 20000 through 30000. These numbers are used for local IP port numbers
when an explicit address is not specified.
The values are sysctl modifiable under: net.inet.ip.port_{first|last}_auto
These numbers do not overlap with any known server addresses, without going
above 32768 which are "negative" on some other implementations.
20000 through 30000 is 2.5 times larger than the old range, but some have
suggested even that may not be enough... (gasp!) Setting a low address
of 10000 should be plenty.. :-)
local address, that was assigned with ifconfig alias and netmask
0xffffffff, would receive duplictae udp packets.
This behaviour can easily be seen by having named run, and using the alias
address as the name server.
This solution is not the pretiest one, but after talk with Garreth, it
is seen as the most easy one.
to enable IP forwarding, use sysctl(8). Also did the same for IPX,
which involved inventing a completely new MIB from whole cloth (which
I may not quite have correct); be aware of this if you use IPX forwarding.
(The two should never have been controlled by the same option anyway.)
than separate ip_v and ip_hl members. Should have no effect on current code,
but I'd eventually like to get rid of those obnoxious bitfields completely.
others: start to populate the link-layer branch of the net mib, by
moving ARP to its proper place. (ARP is not a protocol family, it's an
interface layer between a medium-access layer and a protocol family.)
sysctl(8) needs to be taught about the structure of this branch, unless
Poul-Henning implements dynamic MIB exploration soon.
*' instead of caddr_t and it isn't optional (it never was). Most of the
netipx (and netns) pr_ctlinput functions abuse the second arg instead of
using the third arg but fixing this is beyond the scope of this round
of changes.
Add five sysctl variables that you should probably never tweak.
net.arp.t_prune: 300
net.arp.t_keep: 1200
net.arp.t_down: 20
net.arp.maxtries: 5
net.arp.useloopback: 1
net.arp.proxyall: 0
(It's net.arp because arp isn't limited to inet, though our present
implementation surely is).
Removed ifnet.if_init and ifnet.if_reset as they are generally unused.
Change the parameter passed to if_watchdog to be a ifnet * rather than
a unit number. All of this is an attempt to move toward not needing an
array of softc pointers (which is usually static in size) to point to
the driver softc.
if_ed.c:
Changed some of the argument passing to some functions to make a little
more sense.
if_ep.c, if_vx.c:
Killed completely bogus use of if_timer. It was being set in such a way
that the interface was being reset once per second (blech!).
