/dev/mcd0a instead of /dev/mcd0d. This is more conforming to the /dev/cd0a
for the SCSI cdrom drives. It breaks the convention d the whole drive.
But the question is, do we really need partitions on cdrom drives ?
put vers.o at the end of the loader line. We are simply jumping in the
moment into the first location of the text segment in 386bsd. So the
linking order is very important :-). With the addition of the const
types in newvers.sh we jumped into them. I have experimented with an
entry point specification, but was unsuccessfull. Someone else should
look at this.
devices.i386:
files.i386:
Added entries for a Sony cdrom driver.
1) tty.c: gather all the info about the processes before calling ttyprintf
(which may block).
2) syscons.c: handle asynchronous output properly (data structures may
be corrupted otherwise).
Example:
Application use port cua01
Getty open ttyd1 (allocates rawq,outq,etc) and waits while application
done
Application quits, sioclose issued, ttyfree issued (getty calls revoke)
Getty awakes and goes to panic into initrb (NULL rawq)
a zero cylinder and/or head count, set them and the sector count
to some fictious values. The same already happens if the request
sense is unsuccessfull.
1) A new mechanism has been added to prevent pages from being paged
out called "vm_page_hold". Similar to vm_page_wire, but
much lower overhead.
2) Scheduling algorithm has been changed to improve interactive
performance.
3) Paging algorithm improved.
4) Some vnode and swap pager bugs fixed.
now HUPCL set only in bidir case for callin lines
(this prevents set HUPCL on mouse)
comhardclose:
in addition to HUPCL case now DTR dropped for bidir case
if line was active in and no carrier present now.
(this prevents DTR sleep on mouse)
Subject: Re: Bugs with floppy drives
Date: Tue, 8 Mar 94 9:11:54 CST
The transfer speed was only set in the retry after error, not when
switching drives.
Eliminates vm_fault overhead on process startup and
mmap referenced data for in-memory pages.
(process startup time using in-memory segments *much* faster)
2) Even more efficient pmap code. Code partially cleaned up.
More comments yet to follow.
(generally more efficient pte management)
3) Pageout clustering ( in addition to the FreeBSD V1.1 pagein
clustering.)
(much faster paging performance on non-write behind disk
subsystems, slightly faster performance on other systems.)
4) Slightly changed vm_pageout code for more efficiency and
better statistics. Also, resist swapout a little more.
(less likely to pageout a recently used page)
5) Slight improvement to the page table page trap efficiency.
(generally faster system VM fault performance)
6) Defer creation of unnamed anonymous regions pager until needed.
(speeds up shared memory bss creation)
7) Remove possible deadlock from swap_pager initialization.
8) Enhanced procfs to provide "vminfo" about vm objects and user
pmaps.
9) Increased MCLSHIFT/MCLBYTES from 2K to 4K to improve net &
socket performance and to prepare for things to come.
John Dyson
dyson@implode.root.com
David Greenman
davidg@root.com
it still looks a little suspicious that so many of the status codes are missing
so I'm not going to adopt all of the existing ones yet. Try to be more
descriptive in the use of hex constants.
Changes _only_ take effect if `options LAPTOP' is set.
Note: This one is distinctly dodgy. When my IDE drive spins back up from sleep
mode, it generates this `extra interrupt' condition by spinning back up and
generating an intr, though without any particular action required. This
message coming out every time is rather annoying, and thus disabled.
However, what I'm not at all sure of is whether or not all IDE drives will
behave in the same way, or if perhaps it needs to be done in a more complicated
fashion by detecting this more involved "I've spun up and am just saying hi"
condition. This is a simple change and easy to back out/ammend if anybody has
any better ideas.
hack in the moment for testing purposes and to get the drive going
again.
0x20 means empty drive.
0x30 means closed drive with CDROM inserted.
0x80 means drive pulled out, but door closed.
0xa0 means drive pulled out and door open.
Luckily none of these values are the same as that reported for Ethernet
cards ( 0 for WD8003E, 0x40 for WD8013EPC, 0x60 for NE2000).
The bad part is, the probe code gets the WD8003E so hosed, that it is
no longer usable after it. No problem with the WD8013EPC.
my previous fix too (using wdp_heads controller value) and check
0 heads case too.
Other fixes from Bruce:
2) Fix dk_timeout from 2 to about 4 seconds.
3) wdcontrol not retried on internal error.
4) wdwait return check changed ( "!=0" to "<0" into wdsetctlr,
"<0" to "!=0" into wdgetctlr).
This inetrface should be used from now on.
pseudo device pty xx still keeps its meaning: a maximum of
xx ptys is allowed.
A ringbuffer is now 2040 bytes long, per Garrett Wollman's request.
The changes are inspired by the way NetBSD did it (thanks for that!),
though I made it slihghtly different, including the interface so
at least 75% of the allocated space is deallocated when the tty is
closed.
Note further that it is easy to modify the ringbuffer length runtime.
This will have to wait untill some later date...
-Guido
This inetrface should be used from now on.
pseudo device pty xx still keeps its meaning: a maximum of
xx ptys is allowed.
A ringbuffer is now 2040 bytes long, per Garrett Wollman's request.
The changes are inspired by the way NetBSD did it (thanks for that!),
though I made it slihghtly different, including the interface so
at least 75% of the allocated space is deallocated when the tty is
closed.
Note further that it is easy to modify the ringbuffer length runtime.
This will have to wait untill some later date...
-Guido
>From: bde@kralizec.zeta.org.au (Bruce Evans)
Subject: cache botch in bootstrap
Date: Sun, 20 Feb 94 18:14:35 +1100
The cache in the bootstrap loader didn't allow for the device changing.
This caused surprisingly little trouble - the cache is only for a single
track (or part of a track), and the first access to a new device is
always for an early sector, so there is no problem unless the last access
to the old device was for an early sector. I saw the problem on a system
with BSD on wd1 and no label on wd0. Everything worked if the the device
name wd(1,a) was specified before the default of wd(0,a) was tried, but
when the default was tried, it failed on the first sector because there
was no label, and then the first sector on wd0 was always used instead
of the first sector on wd1, so there was apparently no label on wd1
either.
Bruce
Subject: Bugfix for SB16 with DSP version 4 and above
No description sent, but it appears to fix a major number problem
with certain models of the SB16.
Small hack, if heads > 16, output a warning and then set the head
count to 16. This stops the infinite loop on this error and allows
people to later fix the DOS parameter table later with fdisk.
run Exabyte 8505 on 1742's. This may not be the final solution, but it
makes it work. It may be better to change the DELAY(10) to DELAY(30)
inside the loop instead of increasing the loop count from 100 to 300.
Subject: Bug Fix for ft.c - please commit
Date: Mon, 14 Feb 94 10:22:54 CST
This fixes a bug where the system can crash if the tape is used
after the floppy has been used.
idea considering the old version (but I haven't time for attic surgery - this
is just a caution). This is part of (and the major reason for) the new ld
changes.
a pv chain was being traversed while interrupts were
fully enabled in pmap_remove_all ... this is bogus, and
has been fixed in pmap.c. (sorry for adding the splimp)
Description:
The integer overflow instruction (into) and the interrupt instruction with
value 4 (int #4) both give rise to SIGBUS signals rather than SIGFPE. The
problem is that overflow is a trap not a fault (unlike the BOUND instruction).
>From: Adam David <adam@veda.is>
Subject: SCSI timeout in sdopen()
Date: Sun, 6 Feb 1994 21:40:48 GMT
Index: sys FreeBSD-current
Reference: FreeBSD-current/sys/9
Description:
sdopen() times out on slow SCSI devices. This code was moved into
a different file, which might explain why it got missed again.
Repeat-By:
using slow SCSI disks
When the keyboard is probed, the LED's blink quickly and
"Keyboard reset failed" is printed on the console. The
init routine keeps trying endlessly with the same behavior
as above.
I got the latest -current sup sources (06-Feb-94 12:00 GMT) to work using the
old syscons.c. The following patch makes the new syscons work:
2) Make SNAKE_SAVER like default, if no saver specified in "options"
3) Remove #ifdef STAR_SAVER before line /* make screensaver happy */
this code needed in any case.
Subject: syscons-1.3
Date: Sat, 29 Jan 94 23:33:50 MET
But here is the (hopefully) final syscons-1.3....
....
I've changed sgetc so it works as the pccons parallel
(it now uses a scgetc internally).
[
There were a couple changes that Bruce Evans sent me that were applied
to this version along with some changes that S'ren didn't incorporate
into the final version. There will be only minor changes if anything
from this version to his final release.
]
o merged and fixed timeout code from sos.
o merged DOS partition support from sos.
o fixed "extra" interrupts.
o check if malloc retuns NULL :-(.
o print drive size as in NetBSD
o after an error, return the residual count, not 0.
o give up early for > 16 heads.
o cleaned up the old-drive detection in wdgetctlr().
o rewrote wddump(). I'd been putting this off because
I'd had the dump disabled since 0.0 and had no idea
if even the standard version worked. It didn't:
(0) syscons' sgetc() interface broke some keyboard
stuff.
(1) CADDR1 is mapped using pmap() and pmap got a NULL
pointer trap (at least when I got to wddump() using
call diediedie from ddb) because the pte for CADDR1
is only supposed to be hacked on directly (e.g. in
physcopyseg()).
(2) bad144 handling was not done.
(3) it was slooow (3600 sectors/minute) because my
controller doesn't cache writes.
o miscellaneous other cleanups, e.g., removed scattered
patchkit/terry dates.
o lots of reformatting.
To be done:
o Merge/fix TIH/NetBSD bad144 code (doesn't belong in any
particular driver. Why aren't we using i386/dkbad.c?).
o Merge/fix Dyson/NetBSD clustering code (large parts
should be shared).
o Fix/extend the partition in use bits. Support extended
partitions. This should be shared by all disk drivers. Swap
to a DOS partition so that the swap space can be shared with
linux.
o Don't use polling except for initialization. Need to
reorganise the state machine. Then "extra" interrupts
shouldn't happen (except maybe one for initialization).
o Fix disklabel, boot and driver inconsistencies with
bad144 in standard versions.
o Look at latest linux clustering methods. Our disksort()
gets in the way of clustering.
o cleaned up the ATA changes (needs more work. I think
the ATA specs say that the only thing really wrong with
the original version of wx is that there was no test
for drive-ready before some commands. 400 nsec delay
suffices for almost everything and 400 nsec delay is
usually "free").
netmask or impmask.
2) Fixes from Bruce:
o Changed name of schedsoftcom() to setsofttty() to match
setsoftclock()
o Bool_t isn't used.
o tx_fifo_size is 1 for chips without fifos, 16 for 16550's, to
help to output more efficiently for 16550's (LSR_TXRDY means
that the fifo is empty, not that it has space for one char).
o Changed name of softsio1() to siopoll() and merged compoll()
into siopoll().
o The probe forgot to clear com_mcr after it failed. This is
harmful for 4 single serial ports on 2 interrupts. It makes
partial misconfigurations worse.
o Don't bother initializing static variables that are 0 (bidir
stuff).
o Only initialize t_oflag to TTYDEF_OFLAG if unit == COMCONSOLE,
not if COMCONSOLE is defined.
o Don't call siointr() from comparam() if there is no output in
progress. For the call from sioopen(), there's no output in
progress, and siointr() often saw silo overflows for stale
input because it was called before sioopen() discarded the
input.
o Let ttselect() do the work for select(), so that the fixes for
ttselect() don't have to be duplicated in zillions of drivers.
Yes, I know that IFADDR ioctl is supposed to be deprecated... Note
that the patch was modified by me to fit better into the driver. -DG
...
While porting CAP to 386bsd/pk0.2.4 and now to FreeBSD Release 1.0
I found a couple of bugs associated with the packet filter. Here
are the fixes. I'm posting them here because they apply to
FreeBSD and 386bsd/pk0.2.4 and possibly to other *BSD.
The first occurs when using the packet filter to write raw
ethernet packets. The header consisting of the sender and
destination addresses and the protocol is removed and later
added back on, but with the byte order of the protocol reversed.
The fix ensures that the byte order in the protocol field is
swapped when it is removed.
The second fix ensures that SIOCGIFADDR works for BPF as claimed
in the man pages, by adding it to the ed driver. Similar fixes
will be needed for other ethernet drivers.
Dave Matthews.
file override to disable fifo on 16550s:
I bought a board with two 16550's, but one of those ports has a mouse
on it. The sio driver always enables the fifo, which is a bad thing
for mice and X. The mouse is jerky and hard to use. The simple thing
is be to treat one of the ports as a non-fifo'ed UART, and I use the
flags option in my config file.
So, my config file has:
device sio0 at isa? port "IO_COM1" tty irq 4 flags 0x2 vector siointr
device sio1 at isa? port "IO_COM2" tty irq 3 vector siointr
(patch deleted)
following is a summary:
1) increased object cache back up to a more reasonable value.
2) removed old & bogus cruft from machdep.c (clearseg, copyseg,
physcopyseg, etc).
3) inlined many functions in pmap.c
4) changed "load_cr3(rcr3())" into tlbflush() and made tlbflush inline
assembly.
5) changed the way that modified pages are tracked - now vm_page struct
is kept updated directly - no more scanning page tables.
6) removed lots of unnecessary spl's
7) removed old unused functions from pmap.c
8) removed all use of page_size, page_shift, page_mask variables - replaced
with PAGE_ constants.
9) moved trunc/round_page, atop, ptoa, out of vm_param.h and into i386/
include/param.h, and optimized them.
10) numerous changes to sys/vm/ swap_pager, vnode_pager, pageout, fault
code to improve performance. LRU algorithm modified to be more
effective, read ahead/behind values tuned for better performance,
etc, etc...
cd.c:
Initialize channel info in CDIOCSETVOL ioctl.
Correct CDIOCSTOP and CDIOCEJCET ioctls to use scsi_stop_unit
instead of scsi_start_unit.
Add CDIOCALLOW and CDIOCPREVENT ioctls.
ch.h:
Return EBUSY instead of ENXIO if the device is already in use.
scsi_base.c:
Add scsi_stop_unit routine.
sd.c:
Add mising indirection through sc_link to sd_get_parms routine
when checking for media loaded.
st.c:
Return EBUSY instead of ENXIO if the device is already in use.
Clear the SDEV_WAITING flag in ststart if we do the wakeup call.
Cuddle { braces up where possible on if statements
Add missing splx(s) calls before some returns.
Remove extra semicolon that was keeping uha_init from returning
before the timeout occured. This should speed probing up quite
a bit!
0) FreeBSD additional include files additions
1) Rod's arpacom changes
2) Function type and return code cleanup, and all functions have correct
casting to the correct data types
3) Bugfix where driver would not function due to missing structure not
given a value.
4) General cleanup. (Theo did a lot already, I just did some more)
Removed com port comments, since we are about to depricate the driver.
Fix several plaes in LINT where people have been cutting and pasting using
xterms :-(
the device close routine. This works because the device close calls
the line discipline close (which only flushes the output buffers) and
the ttyclose() routine, which does little of nothing except screw with
the session and process group fields (which is what was causing all
the problems).
Date: Mon, 17 Jan 94 20:52:14 PST
As reported on the -bugs list by some one, and confirmed by Julian:
> I increased AHA_RESET_TIMEOUT in aha1542.c from 1000 to 10000
> and now my 1542C is found everytime.
problem with some chipsets (UMC) remapping the 'hole' memory even when
you've got 16MB. People were led to believe that since there was only
16MB of memory in the machine, that they were okay wrt the ISA DMA
limit. This hack simply causes the extra memory to be ignored if it
appears around the 16MB limit.
* Removed pmap_is_wired
* added extra cli/sti protection in idle (swtch.s)
* slight code improvement in trap.c
* added lots of comments
* improved paging and other algorithms in VM system
Changed the output of the isa probe routine, that only devices, that
have an IO address and are smaller than 0x100 to be on the motherboard.
The seagate SCSI adapter is an example of a card, that doesn't have
an IO address and works only memory mapped.
Choose older MULTIPORT version, because lastest bde version
not worked.
Don't force HUPCL for bidirectional case.
From bde:
Use bit (1 << (16 + 4)) in schedsoftcom() to avoid clash with
non-serial h/w on IRQ4.
Allow FIFO_TRIGGER in config.
Clear com->mcr_image when clearing mcr for init of 4port. The
usual value MCR_IENABLE should have broken 4ports unless
something happened to clear it later.
Turn off interrupts as well as DTR after an error waiting for
carrier (bidir dialin case).
Drain fifo more carefully.
Don't hang up if debugging.
Rearrange siointr() -> siointr1() for multiport case for speed,
lower latency and clarity.
Use suser() to check perms.
Provide missing splx() after failed perms checks.
c_ispeed == 0 means c_ispeed = c_ospeed (POSIX).
Set parameters (except speed) for c_ospeed == 0 as well as
hanging up.
Better initialization for console (fifo stuff...).
Misc. cleanups.
Fix dead hang if modem power is off.
