details of each rman header, but not the contents of all rman structures
in the system. This is especially useful on platforms where some rmans
have many thousands of entries in rmans, making scrolling through the
output of "show all rman" impractical. Individual rmans can then be viewed
including their contents with "show rman 0xaddr" as usual.
Reviewed by: jhb
- make SATA SIMs announce capabilities to handle SDB with Notification bit;
- make PMP driver honor this SIMs capability;
- make SATA XPT to negotiate and enable this feature for ATAPI devices.
This feature allows supporting SATA ATAPI devices to inform system about
some events happened, that may require attention. In my case this allows
LG GH22LS50 SATA DVR-RW drive to report tray open/close events. Events
reported to CAM in form of AC_SCSI_AEN async. Further they could be used
as a hints for checking device status and reporting media change to upper
layers, for example, via spoiling mechanism of GEOM.
diversity.
This is bit dirty and likely should be revised at a later date,
with an eye to unifying/tidying up the whole diversity setup
and allowing developers to do "tricky stuff" as they desire.
For now, this works.
* add a new method, specifically for doing per-RX packet
antenna diversity
* set that HAL method only if it's Kite and a Kite chip that
does diversity.
* add a diversity flag to the HAL debugging section
* add a check to make sure the kite diversity code doesn't run
on boards that don't require it, as not all Kite chips will
implement it.
* add some debug statements when the diversity code makes
changes to the antenna diversity/combining setup.
controller port readiness (that should set just after PHY ready signal),
reduce wait time from 10s to 1s before trying more aggressive reset method.
This should improve system responsibility in some failure conditions.
Note: this HAL currently only supports the AR9285.
From Linux ath9k:
The problem is that when the attenuation is increased,
the rate will start to drop from MCS7 -> MCS6, and finally
will see MCS1 -> CCK_11Mbps. When the rate is changed b/w
CCK and OFDM, it will use register desired_scale to calculate
how much tx gain need to change.
The output power with the same tx gain for CCK and OFDM modulated
signals are different. This difference is constant for AR9280
but not AR9285/AR9271. It has different PA architecture
a constant. So it should be calibrated against this PA
characteristic.
The driver has to read the calibrated values from EEPROM and set
the tx power registers accordingly.
not believe that these leaks had a practical impact,
since the situations in which they would have occurred
would have been extremely rare.
MFC after: 2 weeks
MPERF MSRs are available. It was disabled in r216443. Remove the earlier
hack to subtract 0.5% from the calibrated frequency as DELAY(9) is little
bit more reliable now.
Instead of spinning in a tight loop for up to 15 seconds, polling for device
readiness while it spins up, return reset completion just after PHY reports
"connect well" or 100ms connection timeout. If device was found, use callout
for checking device readiness with 100ms period up to full 31 second timeout.
This fixes system freeze for 5-10 seconds on drives hot plug-in.
embedded flash stores.
Some devices - notably those with uboot - don't have an
explicit partition table (eg like Redboot's FIS.)
geom_map thus provides an easy way to export the hard-coded
flash layout as geom providers for use by filesystems and
other tools.
It also includes a "search" function which allows for
dynamic creation of partition layouts where the device only
has a single hard-coded partition. For example, if
there is a "kernel+rootfs" partition, a single image can
be created which appends the rootfs after the kernel with
an appropriate search string. geom_map can be told to
search for said search string and create a partition
beginning after it.
Submitted by: Aleksandr Rybalko <ray@dlink.ua>
bus driver at detach, hence ehci_detach() does exactly this since r199718.
Submitted by: Luiz Otavio O Souza
MFC after: 7 days
Approved by: thompsa (mentor)
of NFSv2 getting an error return from VOP_MKNOD(). Without this
patch, the server file system remains busy after an NFSv2
VOP_MKNOD() fails.
MFC after: 2 weeks
SCSI status errors to CAM (that was wrong, as it too often turned retriable
wire errors into non-retriable REQUEST SENSE errors), do it only for STALL
errors on control pipe of the CBI devices. STALL on control pipe is just
a one of the ways to report error for CBI devices.
PR: usb/150401, usb/154593.
Reviewed by: hselasky
MFC after: 1 week
for a new journal specific partial truncate routine.
- Use dep_current[] in place of specific dependency counts. This is
automatically maintained when workitems are allocated and has
less risk of becoming incorrect.
the experimental NFS server, so that it doesn't leak memory
when unloaded. However, unloading the NFSv4 server is not
recommended, since all NFSv4 state will be lost by the unload
and clients will have to recover the state after a server
reload/restart as if the server crashed/rebooted.
MFC after: 2 weeks
- Keep a hash of indirect blocks that have recently been freed and are
still referenced in the journal.
- Lookup blocks in this hash before forcing a new block write to wait on
the journal entry to hit the disk. This is only necessary to avoid
confusion between old identities as indirects and new identities as
file blocks.
- Don't free jseg structures until the journal has written a record that
invalidates it. This keeps the indirect block information around for
as long as is required to be safe.
- Force an empty journal block write when required to flush out stale
journal data that is simply waiting for the oldest valid sequence
number to advance beyond it.
VOP_LOOKUP() returned. This fixes a bug in the experimental
NFS server for the case where VFS_VGET() fails returning EOPNOTSUPP
in the ReaddirPlus RPC, forcing the use of VOP_LOOKUP() instead.
MFC after: 2 weeks
workaround for fdescfs to not panic when ncookies is not NULL, similar
to the one committed as r152254, but simpler, due to fdescfs_readdir()
not calling vfs_read_dirent().
PR: kern/156177
MFC after: 1 week
