event generation is disabled by default in favour of kbdmux. This
behavoiur is controlled by kern.evdev.rcpt_mask sysctl, bit 3 should
be set to give priority to hw over mux
Submitted by: Vladimir Kondratiev <wulf@cicgroup.ru>
Reviewed by: hans
Differential Revision: https://reviews.freebsd.org/D7957
mutexes or using any callouts when active.
Trying to lock a mutex when KDB is active or the scheduler is stopped
can result in infinite wait loops. The same goes for calling callout
related functions which in turn lock mutexes.
If the USB controller at which a USB keyboard is connected is idle
when KDB is entered, polling the USB keyboard via USB will always
succeed. Else polling may fail depending on which state the USB
subsystem and USB interrupt handler is in. This is unavoidable unless
KDB can wait for USB interrupt threads to complete before stalling the
CPU(s).
Tested by: Bruce Evans <bde@freebsd.org>
MFC after: 4 weeks
Split usbd_xfer_status() check:
- Check xfer length: must be longer, than Rx descriptor size.
- Check frame size: must be shorter than xfer length.
- Discard too short frames.
Tested with WUSB54GC, STA/MONITOR modes.
by reviving the SX control request lock and refining which lock
protects the common scratch area in "struct usb_device".
The SX control request lock was removed by r246759 because it caused a
lock order reversal with the USB enumeration lock inside
usbd_transfer_setup() as a function of r246616. It was thought that
reducing the number of locks would resolve the LOR, but because some
USB device drivers use usbd_do_request_flags() inside callback
functions, like in taskqueues, a deadlock may occur when these are
drained from device_detach(). By restoring the SX control request
lock usbd_do_request_flags() is allowed to complete its execution
when a USB device driver is detaching. By using the SX control request
lock to protect the scratch area, the LOR introduced by r246616 is
also resolved.
Bump the FreeBSD version while at it to force recompilation of all USB
kernel modules.
Found by: avos@
MFC after: 1 week
sys/dev/usb/serial/uplcom.c:543:29: error: implicit conversion from 'int' to 'int8_t' (aka 'signed char') changes value from 192 to -64 [-Werror,-Wconstant-conversion]
if (uplcom_pl2303_do(udev, UT_READ_VENDOR_DEVICE, UPLCOM_SET_REQUEST, 0x8484, 0, 1)
~~~~~~~~~~~~~~~~ ^~~~~~~~~~~~~~~~~~~~~
sys/dev/usb/usb.h:179:53: note: expanded from macro 'UT_READ_VENDOR_DEVICE'
#define UT_READ_VENDOR_DEVICE (UT_READ | UT_VENDOR | UT_DEVICE)
~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~
This is because UT_READ is 0x80, so the int8_t argument is wrapped to a
negative value. Fix this by using uint8_t instead.
Reviewed by: imp, hselasky
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D7776
Use sbintime_t timeouts with precision control to get very accurate
timing. It costs little to always ask for about 1% accuracy, and the
not so new event timer implementation usual delivers that, and when
it can't it gets much closer than our previous coarse timeouts and
buggy simple countdown.
The 2 fastest atkbd repeat rates have periods 34 and 38 msec, and ukbd
pretended to support rates in between these. This requires
sub-microsecond precision and accuracy even to handle the 4 msec
difference very well, but ukbd asked the timeout subsystem for timeouts
of 25 msec and the buggy simple countdown of this gave a a wide range
of precisions and accuracies depending on HZ and other timer
configuration (sometimes better than 25 msec but usually more like 50
msec). We now ask for and usually get precision and accuracy of about
1% for each repeat and much better on average.
The 1% accuracy is overkill. Rounding of 30 cps to 34 msec instead of
33 already gives an error of +2% instead of -1%, and ut AT keyboards on
PS/2 interfaces have similar errors.
A timeout is now scheduled for every keypress and release. This allows
some simplifications that are not done. It allows removing the timeout
scheduling for exiting polled mode where it was unsafe in ddb mode. This
is done. Exiting polled mode had some problems with extra repeats. Now
exiting polled mode lets an extra timeout fire and the state is fudged
so that the timeout handler does very little.
The sc->time_ms variable is unsigned to avoid overflow. Differences of
it need to be signed. Signed comparisons were emulated by testing an
emulated sign bits. This only works easily for '<' comparisonss, but
we now need a '<=' comparison. Change the difference variable to
signed and use a signed comparison. Using unsigned types here didn't
prevent overflow bugs but just reduced them. Overflow occurs with
n repeats at the silly repeat period of [U]INT_MAX / n. The old countdown
had an off by 1 error, and the simplifications would simply count down
1 to 0 and not need to accumulate possibly-large repeat repeats.
kbdcontrol -r fast is documented to give a non-emulated atkbd's fastest
rate of 250.34, but is misimplemented to request this as 0.0. ukbd
supports many nonstandard rates, although it is currently too inaccurate
by a factor of several hundred for non-huge nonstandard rates to be
useful. It mapped 0.0 to 200.0. A repeat delay of 0 means a rate of
infinity which is quite fast, but physical constraints limit this to
a few MHz and the inaccuracies made it almost usable.
Convert 0.0 to the documented 250.34.
Also convert negative args and small args to the 250.34 minimal ones,
like atkbd does. This is for KDSETREPEAT -- the 2 versions of the
deprecated KDSETRAD have bounds checking. Keep not doing any bounds
checking or conversions for upper limits since nonstandard large
delays are useful for testing.
The inaccuracies are dependent on HZ and the timeout implementation.
With the old timeout implementation and HZ = 1000, 200.0 probably
worked better to emulate 250.34 than 250.34 itself. HZ = 100 gives
roundoff errors that accidentally reduce the inaaccuracies, and
event timers reduce the inaccuracies even more, so 200.0 was giving
more like itself (perhaps 215.15 on average but sometimes close to
10 msec repeat which is noticebly too fast). This commit makes 0.0
noticeably too slow, like 250.34 always was.
So that Hyper-V can leverage them instead of rolling its own definition.
Discussed with: hps
Reviewed by: hps
MFC after: 1 week
Sponsored by: Microsoft
Differential Revision: https://reviews.freebsd.org/D7592
its own job because this breaks the simplified QEMU XHCI TRB parser,
which expects the complete USB control transfer as a series of back to
back TRBs. The old behaviour is kept under #ifdef in case this change
breaks enumeration of any USB devices.
PR: 212021
MFC after: 1 week
The previous fix was tested mainly on 3 AT keyboards with USB adaptors where
it works. 1 USB keyboard doesn't translate Alt-PrintScreen, so the software
has to do it.
Reorganize a little to share some code and to not translate the unusual usb
scan code0x8a unless an Alt modified is set. Remove redundant check of Alt
modifiers. Translation now more clearly filters out Alt-PrintScreen before
the check.
The table of errors fixed in the previous commit had many bugs. Correct
table:
K_RAW Ctl-PrintScreen: E0-2A-E0-37 -> E0-37
K_RAW Alt-PrintScreen (with 4 comb. of Ctl/Shift): 79 -> 54
K_RAW Pause/Break (with 4 comb. of Alt/Shift): E0-46 -> E1-1D-45
K_CODE PrintScreen (with 4 comb. of Ctl/Shift): 54 -> 5c
K_CODE Alt-PrintScreen (with 4 comb. of Ctl/Shift): 7e -> 54
K_CODE Pause/Break (with 8 comb. of Ctl/Alt/Shift): 6c -> 68
That is 25 of 32 shift combinations for 2 keys fixed. All 16 combinations
were broken for K_CODE and thus also for K_XLATE.
configuring of EP0 and non-EP0 into xhci_cmd_evaluate_ctx() and
xhci_cmd_configure_ep() respectivly. This resolves some errors when
using XHCI under QEMU and gets is more in line with the XHCI
specification.
PR: 212021
MFC after: 1 week
so they are memory independent which allows for handling panics
triggered by the keyboard driver itself, typically via CTRL+ALT+ESC
sequences. Or if the USB keyboard driver was processing a key at the
moment of panic. Allow UKBD to be attached while keyboard polling is active.
Tested by: Bruce Evans <bde@freebsd.org>
MFC after: 1 week
everything was broken. The cases that I noticed were Ctrl-PrintScreen
not being mapped to the virtual scancode 0x5c (debug) and Pause not being
mapped to the physical/virtual scancode 0x46 (slock).
These keys are the most complicated ones due to kludges to give some
compatibility back to before AT keyboards.
Alt-PrintScreen must pretend to be a separate key from PrintScreen
even at the "raw" level. The (unique) usb code for it is 0x8a and we
just have to map this to our unique virtual scancode 0x54, but we
mapped it first to the internal code 0x7e and then to 0x79 which is a
key on the Japanese 106/109 keyboard. This fix is under the
UKBD_EMULATE_ATASCANCODE option which shouldn't be used for non-AT
keyboards. If it is, then the syscons Japanese keymaps have nothing
of importance for code 0x79 and can easily be changed. 0x54 is also
unimportant in Japanese and US keymaps.
NonAlt-PrintScreen and NonCtl-Pause/Break had many much larger bugs with
smaller compatibility problems from fixing them. The details are too
ugly to give here. Summary of the changed (hex) codes:
K_RAW PrintScreen (Ctl, Shift, Ctl-Shift): E0-2A-E0-37 -> E0-37
K_RAW Alt-PrintScreen (all shift states): 79 -> 54
K_RAW Pause/Break (unshifted, Shift, Alt, Alt-Shift)): E0-46 -> E1-1D-45
K_CODE ALT-PrintScreen (all shift states): 79 -> 54
That is 15 of 32 shift combinations for 2 keys fixed, with 8 easy cases
from the 79 -> 54 remapping.
The difference is only large and with no workaround using a keymap for
for K_RAW, but this affects other modes when ukbd is layered under kbmux
because kbmux keeps all subdevices in K_RAW mode and translates. Oops.
I used kbdmux to generate the above table of changes.
axge_setmulti()/axge_setpromisc() with axge_rxfilter().
Multicast filter programming and promiscuous mode requires
access to a common RX configuration register so there is no need to
use separate functions with added complexity. axge_rxfilter() does
not read back AXGE_RCR register since accessing a register in USB
is too slow and we already have all knowledge of required
configuration. Rebuilding RX filter configuration is simpler and
faster than manipulating every bits after reading back the
register.
Note, axge_rxfilter() does not set RCR_IPE(IP header alignment on
32bit boundary) to disable extra padding bytes insertion. The
extra padding wastes ethernet to USB host bandwidth as well as
complicating RX handling logic. Current USB framework requires
copying RX frames to mbufs so there is no need to worry about
alignment. Previously axge_rx_frame() performed wrong bound check
due to the extra padding and it was broken when RX checksum
offloading is disabled. See added comment in axge_rx_frame () for
actual RX packet layout.
In axge_init(), disable WOL. It's meaningless to enable WOL in
normal operation.
In axge_rxeof(), use properly sized mbuf rather than blindly
allocating a mbuf cluster.
Use RX H/W checksum offloading only when administrator requested RX
checksum offloading. Previously it always used RX H/W checksum
offloading result regardless of RX checksum offloading state.
Separate L4 checksum offloading validation from L3 one and properly
set required offloading bits for each layer. This is to fix setting
L4 checksum offloading bits for L3 packets.
There are still lots of RX errors(probably RX FIFO overflows) under
moderate load. Users are strongly recommended to enable ethernet
flow control.
Reviewed by: kevlo (initial version), hselasky
structures. This simplifies mbuf copy operation to USB buffers as
well as improving readability. The controller supports Microsoft
LSOv1(aka TSO) but this change set does not include the support due
to copying overhead to USB buffers and large amount of memory waste.
Remove useless ZLP padding which seems to come from Linux. Required
bits the code tried to set was not copied into USB buffer so it had
no effect. Unlike Linux, FreeBSD USB stack automatically generates
ZLP so no explicit padding is required in driver.[1]
Micro-optimize updating IFCOUNTER_OPACKETS counter by moving it out
of TX loop since updating counter is not cheap operation as it did
long time ago and we already know how many number of packets were
queued after exiting the loop.
While here, fix a checksum offloading bug which will happen when
upper stack computes checksum while H/W checksum offloading is
active. The controller should be notified to not recompute the
checksum in this case.
Reviewed by: kevlo (initial version), hselasky
Pointed out by: hselasky [1]
Uses of commas instead of a semicolons can easily go undetected. The comma
can serve as a statement separator but this shouldn't be abused when
statements are meant to be standalone.
Detected with devel/coccinelle following a hint from DragonFlyBSD.
MFC after: 1 month
only for now, but wouldn't be too difficult to add support for FDT.
Reviewed by: hselasky
Obtained from: ABT Systems Ltd
MFC after: 1 month
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D7352
The hardware delivers ns16550-compatible status bits, which is what the
usb_serial code expects, so no need for translation, no need for a local
variable to hold a temporary lsr result.
In some cases, the driver must handle given properties located in
specific OF subnode. Instead of creating duplicate set of function, add
'node' as argument to existing functions, defaulting it to device OF node.
MFC after: 3 weeks
version of the XHCI specification. Make sure the code can handle the
maximum number of allowed scratch pages.
Submitted by: Shichun_Ma@Dell.com
Approved by: re (hrs)
MFC after: 1 week
