allowed range or when one or more pages are not mapped. This according to
The Open Group Base Specifications Issue 7.
Discussed with: attilio, Bruce Evans
Reviewed by: alc, Garrett Cooper
Reported by: ATF
MFC after: 2 weeks
Sponsored by: EMC / Isilon storage division
mprsas_SSU_to_SATA_devices().
This fixes an assertion on shutdown with INVARIANTS enabled with SATA
drives present on an IR firmware controller.
Reviewed by: Steve McConnell <stephen.mcconnell@avagotech.com>.
MFC after: 3 days
a journal block even when there are no journal entries to be written.
Until the root cause is found, handle this case by ensuring that a
valid journal segment is always written.
Second, the data buffer used for writing journal entries was never
being scrubbed of old data. Fix this.
Submitted by: Takehara Mikihito
Obtained from: Netflix, Inc.
MFC after: 3 days
4730 metaslab group taskq should be destroyed in metaslab_group_destroy()
Reviewed by: Alex Reece <alex.reece@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Sebastien Roy <sebastien.roy@delphix.com>
Original author: George Wilson
MFC after: 3 days
case where the controller is already enabled.
Some of the pl310 configuration registers cannot be changed while the
controller is active, so if there is any platform-specific init to be done
it must happen before enabling the controller.
The controller should not be enabled upon entry to the kernel, but u-boot
has recently developed the bad habit of leaving caches enabled when
launching the kernel, and since we have no control over that source code
we have to do our best to cope with it. The PL310 manual doesn't document
a safe sequence for disabling the controller, but the sequence used here
(force write-through mode and disable linefill allocations, then clean and
invalidate the current contents before disabling the hardware) appears to
be sound both by analysis and empirical testing.
These changes were developed and tested in collaboration with
Svatopluk Kraus <onwahe@gmail.com>.
Reviewed by: cognet@
controller driver by piggybacking the SOF interrupt when issuing new
and checking old transfers. Number of interrupts was reduced by 30%
when doing Isochronous transfers.
Use correct GINTMSK_XXX macros when accessing the DWC OTG interrupt
mask register.
Add code to adjust the frame interval register which influences the
SOF rate.
MFC after: 2 weeks
This problem only occurs on versions of FreeBSD prior to the recent CAM
locking changes. (i.e. stable/9 and older versions of stable/10) This
change should be a no-op for head and stable/10.
If a path isn't specified, xpt_register_async() will create a fully
wildcarded path and acquire a lock (the XPT lock in older versions,
and via xpt_path_lock() in newer versions) to call xpt_action() for the
XPT_SASYNC_CB CCB. It will then drop the lock and if the requested event
includes AC_FOUND_DEVICE or AC_PATH_REGISTERED, it will get the caller up
to date with any device arrivals or path registrations.
The issue is that before the locking changes, each SIM lock would get
acquired in turn during the EDT tree traversal process. If a path is
specified for xpt_register_async(), it won't acquire and drop its own lock,
but instead expects the caller to hold its own SIM lock. That works for
the first part of xpt_register_async(), but causes a recursive lock
acquisition once the EDT traversal happens and it comes to the SIM in
question. And it isn't possible to call xpt_action() without holding a SIM
lock.
The locking changes fix this by using the XPT topology lock for EDT
traversal, so it is no longer an issue to hold the SIM lock while calling
xpt_register_async().
The solution for FreeBSD versions before the locking changes is to request
notification of all device arrivals (so we pass a NULL path into
xpt_register_async()) and then filter out the arrivals that are not ours.
MFC After: 3 days
Sponsored by: Spectra Logic Corporation
periodically update the reference status of the active pages. This function
was called, instead of vm_pageout_scan(), when memory was not scarce. The
objective was to provide up to date reference status for active pages in
case memory did become scarce and active pages needed to be deactivated.
The active page queue scan performed by vm_pageout_page_stats() was
virtually identical to that performed by vm_pageout_scan(), and so r254304
eliminated vm_pageout_page_stats(). Instead, vm_pageout_scan() is
called with the parameter "pass" set to zero. The intention was that when
pass is zero, vm_pageout_scan() would only scan the active queue. However,
the variable page_shortage can still be greater than zero when memory is not
scarce and vm_pageout_scan() is called with pass equal to zero.
Consequently, the inactive queue may be scanned and dirty pages laundered
even though that was not intended by r254304. This revision fixes that.
Reported by: avg
MFC after: 1 week
Sponsored by: EMC / Isilon Storage Division
used.
It turns out that the RX DMA engine does the same last-descriptor-link-
pointer-re-reading trick that the TX DMA engine. That is, the hardware
re-reads the link pointer before it moves onto the next descriptor.
Thus we can't free a descriptor before we move on; it's possible the
hardware will need to re-read the link pointer before we overwrite
it with a new one.
Tested:
* AR5416, STA mode
TODO:
* more thorough AP and STA mode testing!
* test on other pre-AR9380 NICs, just to be sure.
* Break out the RX descriptor grabbing bits from the RX completion
bits, like what is done in the RX EDMA code, so ..
* .. the RX lock can be held during ath_rx_proc(), but not across
packet input.
same events that tcpstat's tcps_rcvmemdrop counter counts.
- Rename tcps_rcvmemdrop to tcps_rcvreassfull and improve its
description in netstat(1) output.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
thicket of .if ${COMPILER_TYPE} == "clang" that controls
warnings. Also, use CFLAGS.clang in a couple places in preference to
having a similar construct that's related to the CWARNFLAGS changes.
o Declare vt(4) drivers dataset.
o Create single static structures for all early drivers.
o Add vt(4) to be by default in the kernel consoles list.
o Create one more sysinit point, to be able to initialize memory and lock
requirement of early drivers.
o Implement early drivers select. (Only best available will be selected).
o Fix one missed "return (0)" for VTYLOCK.
o Improve locking for cases when one driver replace another.
o Make driver replacement notification less debug-look-like.
Minor spell fixes.
Sponsored by: The FreeBSD Foundation
reflect when unmapped I/O support was added.
For FreeBSD 10, it arrived just prior to __FreeBSD_version 1000028.
For FreeBSD 9, it arrived just prior to __FreeBSD_version 902001.
Also, fix compiler warnings in mprsas_send_smpcmd() that happen in the
i386 PAE build for non-unmapped I/O builds. These were fixed in mps(4)
in revision 241145, but didn't make it into the mpr(4) driver. This
change should only affect FreeBSD versions outside the above revisions,
and thus doesn't affect head.
MFC after: 3 days
Sponsored by: Spectra Logic Corporation
rman_reserve_resource_bound() to return incorrect results.
Continue the initial search until the first viable region is found.
Add a comment to explain the search termination test.
PR: kern/188534
Reviewed by: jhb (previous version)
MFC after: 1 week
platforms, because these platforms do not implement the ISA DMA
API. Else the sound modules cannot be loaded when running these
platforms.
MFC after: 2 weeks
speed data traffic going directly to a USB device or through a
so-called USB transaction translator.
Add checks that we are not overusing the TX FIFO.
MFC after: 2 weeks
the provider - also apply to UFS1 filesystems. This should help with
resizing filesystems created by makefs(8), which still uses UFS1.
Tested by: jmg@
Sponsored by: The FreeBSD Foundation
call, which assumes the hardware is awake.
Turn ath_update_mcast() into a routine that's only called from the
net80211 layer - and it forces the hardware awake first.
This fixes a LOR from the EDMA RX path which calls ath_mode_init()
with the RX lock held - the driver lock can't also be grabbed.
This path assumes that the ath_mode_init() callers all wake up
the NIC first.
Tested:
* AR9485, STA mode, powersave
This seems to probe/attach as an AR9485 and thus nothing else besides
adding the device id seems to be required.
ath0: <Atheros AR1111> mem 0xf4800000-0xf487ffff irq 19 at device 0.0 on pci5
ath0: [HT] enabling HT modes
ath0: [HT] enabling short-GI in 20MHz mode
ath0: [HT] 1 stream STBC receive enabled
ath0: [HT] 1 RX streams; 1 TX streams
ath0: AR9485 mac 576.1 RF5110 phy 1926.8
ath0: 2GHz radio: 0x0000; 5GHz radio: 0x0000
The NIC I have here is a 1 antenna, 2GHz only device.
Thankyou to Jim Thompson <jim@netgate.com> for the AR1111 NIC.
Tested:
* AR1111 (pretending not to be an AR9485, but failing miserably);
STA mode with powersave.
Relnotes: yes
Sponsored by: Netgate
mixing on stack memory and UMA memory in one linked list.
Thus, rewrite TCP reassembly code in terms of memory usage. The
algorithm remains unchanged.
We actually do not need extra memory to build a reassembly queue.
Arriving mbufs are always packet header mbufs. So we got the length
of data as pkthdr.len. We got m_nextpkt for linkage. And we need
only one pointer to point at the tcphdr, use PH_loc for that.
In tcpcb the t_segq fields becomes mbuf pointer. The t_segqlen
field now counts not packets, but bytes in the queue. This gives
us more precision when comparing to socket buffer limits.
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
freebsd-current. These CPU speed control techniques are usually unhelpful
at best. For now, continue building the relevant code into GENERIC so that
it can trivially be re-enabled at runtime if anyone wants it.
MFC after: 1 month
