when determining the size of a BAR by writing all 1's to the BAR and
reading back the result, always operate on the full 64-bit size.
Reviewed by: imp
MFC after: 1 month
flag when calling bus_alloc_resource() to allocate resources from a parent
PCI bridge. For PCI-PCI bridges this asks the bridge to satisfy the
request using the prefetchable memory range rather than the normal
memory range.
Reviewed by: imp
Reported by: scottl
MFC after: 1 week
BAR could be allocated twice by different children of a vgapci0 device.
To fix this, change the vgapci0 device to track references on its associated
resources so that they are only allocated once from the parent PCI bus and
released when no children are using them. Previously this leaked a small
amount of KVA on at least some architectures.
We now explicitly enable INTx during bus_setup_intr() if it is needed.
Several of the ata drivers were managing this bit internally. This is
better handled in pci and it should work for all drivers now.
We also mask INTx during bus_teardown_intr() by setting this bit.
Reviewed by: jhb
MFC after: 3 days
A while back, Warner changed the PCI bus code to reserve resources when
enumerating devices and simply give devices the previously allocated
resources when they call bus_alloc_resource(). This ensures that address
ranges being decoded by a BAR are always allocated in the nexus0 device
(or whatever device the PCI bus gets its address space from) even if a
device driver is not attached to the device. This patch extends this
behavior further:
- To let the PCI bus distinguish between a resource being allocated by
a device driver vs. merely being allocated by the bus, use
rman_set_device() to assign the device to the bus when it is owned
by the bus and to the child device when it is allocated by the child
device's driver. We can now prevent a device driver from allocating
the same device twice. Doing so could result in odd things like
allocating duplicate virtual memory to map the resource on some
archs and leaking the original mapping.
- When a PCI device driver releases a resource, don't pass the request
all the way up the tree and release it in the nexus (or similar device)
since the BAR is still active and decoding. Otherwise, another device
could later allocate the same range even though it is still in use.
Instead, deactivate the resource and assign it back to the PCI bus
using rman_set_device().
- pci_delete_resource() will actually completely free a BAR including
attemping to disable it.
- Disable BAR decoding via the command register when sizing a BAR in
pci_alloc_map() which is used to allocate resources for a BAR when
the BIOS/firmware did not assign a usable resource range during boot.
This mirrors an earlier fix to pci_add_map() which is used when to
size BARs during boot.
- Move the activation of I/O decoding in the PCI command register into
pci_activate_resource() instead of doing it in pci_alloc_resource().
Previously we could actually enable decoding before a BAR was
initialized via pci_alloc_map().
Glanced at by: bsdimp
This addresses interrupt storms that were noticed after enabling MSI
in drm. I think this is due to a loose interpretation of the PCI 2.3
spec, which states that a function using MSI is prohibitted from using
INTx. It appears that some vendors interpretted that to mean that they
should handle it in hardware, while others felt it was the drivers
responsibility.
This fix will also likely resolve interrupt storm related issues with
devices other than drm.
Reviewed by: jhb@
MFC after: 3 days
device. The details include the current value of the BAR (including all
the flag bits and the current base address), its length, and whether or not
it is enabled. Since this operation is not invasive, non-root users are
allowed to use it (unlike manual config register access which requires
root). The intention is that userland apps (such as Xorg) will use this
interface rather than dangerously frobbing the BARs from userland to
obtain this information.
- Add a new sub-mode to the 'list' mode of pciconf. The -b flag when used
with -l will now list all the active BARs for each device.
MFC after: 1 month
by writing all 1's to it to determine its length. This fixes issues with
MCFG on at least some machines where a trashed BAR claimed subsequent
attempts at PCI config transactions because the addresses in the MCFG
window fell in the decoding range of the BAR.
In general it is a bad idea to leave the BARs enabled while we are
frobbing with them in this manner.
Sleuthing by: tegge
MFC after: 1 week
to vga_pci.c to request on behalf of it's children. This causes vgapci to show
up as the interrupt owner in vmstat -i, rather than the child device.
Approved by: jhb(mentor)
only in low memory situations, so the error fork of these fixes is
lightly tested, but they should do the least-wrong thing...
Submitted by: Hans Petter Selasky
memory area's base and limit are optional. The low 4-bits of the "low"
prefetchable registers indicates whether or not a 32-bit or 64-bit
region is supported. The PCI-PCI driver had been assuming that all bridges
supported a 64-bit region (and thus the two upper 32-bit registers). Fix
the driver to only use those registers if the low 4-bits of the "low"
registers indicate that a 64-bit region is supported. The PCI-PCI bridge
in the XBox happens to be a bridge that only supports a 32-bit region.
Reported by: rink
MFC after: 1 week
domain, pribus (the primary bus, eg the bus that this chip is on),
secbus (the secondary bus, eg the bus immediately behind this chip)
and subbus (the number of the highest bus behind this chip).
Normally, this information is reported via bootverbose parameters, but
that's hard to use for debugging in some cases.
This adds reading of pribus to make this happen. In addition, change
the narrow types to u_int to allow for easier reporting via sysctl for
domain, secbus and subbus. This should have no effect, but if it
does, please let me know.
pci_add_map(). First, this condition is already handled earlier in
the function. Second, as written the check would never fire as the
'start' value was overwritten with a long value (rman_get_start() returns
long) before the comparison was done.
Discussed with: imp
MFC after: 2 weeks
for a PCI device during the boot-time probe of the parent PCI bus, then
zero the BAR and clear the resource list entry for that BAR. This forces
the PCI bus driver to request a valid resource range from the parent bridge
driver when the device driver tries to allocate the BAR. Similarly, if the
initial value of a BAR is a valid range but it is > 4GB and the current OS
only has 32-bit longs, then do a full teardown of the initial value of the
BAR to force a reallocation.
Reviewed by: imp
MFC after: 1 week
used but MSI to HyperTransport IRQ mapping is enabled, and would act as
if MSI is turned on, resulting in interrupt loss.
This commit will,
1. enable MSI mapping on a device only when MSI is enabled for that
device and the MSI address matches the HT mapping window.
2. enable MSI mapping on a bridge only when a downstream device is
allocated an MSI address in the mapping window
PR: kern/118842
Reviewed by: jhb
MFC after: 1 week
PCI-express chipset (and thus has functional MSI) if there are any
PCI-express devices in the system, not requiring a root port device.
With PCI-X the chipset detection has to be very conservative because there
are known systems with PCI-X devices that do not appear to have PCI-X
chipsets. However, with PCI-express I'm not sure it is possible to have
a PCI-express device in a system with a non-PCI-express chipset. If we
assume that is the case then this change is valid. It is also required
for at least some PCI-express systems that don't have any devices with
a root port capability (some ICH9 systems).
MFC after: 1 week
Reported by: jfv
but reread it from the device_t every time the device list is fetched.
Previously the device name in pciconf -l would not be updated when a driver
was unloaded or if a device was detached and attached to a different
driver.
MFC after: 1 week
PR: kern/104777
Submitted by: "Iasen Kostoff" tbyte | otel net
- Use the correct offsets when copying out the results of PCIOCGETCONF_OLD.
This happened to not affect the 64-bit architectures because there the
addition of pc_domain to struct pcisel didn't change the overall size of
struct pci_conf. [1]
- Always copy the name and unit information to conf_old so it's also part
of the output once this information is cached in dinfo.
- Use the correct type for flags in struct pci_match_conf_old. This
change is more or less cosmetic though.
Reported and tested by: bde [1]
Reviewed by: imp
MFC after: 3 days
Committed from: 24C3
- Implement timing out of VPD register access.[1]
- Fix an off-by-one error of freeing malloc'd space when checksum is invalid.
- Fix style(9) bugs, i.e., sizeof cannot be followed by space.
- Retire now obsolete 'hw.pci.enable_vpd' tunable.
Submitted by: cokane (initial revision)[1]
Reviewed by: marius (intermediate revision)
Silence from: jhb, jmg, rwatson
Tested by: cokane, jkim
MFC after: 3 days
the PCIOCGETCONF, PCIOCREAD and PCIOCWRITE IOCTLs, which was broken
with the introduction of PCI domain support.
As the size of struct pci_conf_io wasn't changed with that commit,
this unfortunately requires the ABI of PCIOCGETCONF to be broken
again in order to be able to provide backwards compatibility to
the old version of that IOCTL.
Requested by: imp
Discussed with: re (kensmith)
Reviewed by: PCI maintainers (imp, jhb)
MFC after: 5 days
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
the duration of the function. The device we would otherwise
have left in an useless state may just as well be the low-level
console. When booting verbose, we do need it addressable if we
want to avoid a MCA.
Approved by: re (kensmith)
device's, not the bridge's, softc to be used to check the
PCIB_DISABLE_MSI flag. This resulted in randomly allowing
or denying MSI interrupts based on whatever value the driver
happened to store at sizeof(device_t) bytes into its softc.
I noticed this when I stopped getting MSI interrupts
after slighly re-arranging mxge's softc yesterday.
the power_nodriver tunable is off. pci_cfg_save() already checks the
tunable internally, and no other callers of pci_cfg_save() check the
tunable.
Reviewed by: imp
- Simplify the amount of work that has be done for each architecture by
pushing more of the truly MI code down into the PCI bus driver.
- Don't bind MSI-X indicies to IRQs so that we can allow a driver to map
multiple MSI-X messages into a single IRQ when handling a message
shortage.
The changes include:
- Add a new pcib_if method: PCIB_MAP_MSI() which is called by the PCI bus
to calculate the address and data values for a given MSI/MSI-X IRQ.
The x86 nexus drivers map this into a call to a new 'msi_map()' function
in msi.c that does the mapping.
- Retire the pcib_if method PCIB_REMAP_MSIX() and remove the 'index'
parameter from PCIB_ALLOC_MSIX(). MD code no longer has any knowledge
of the MSI-X index for a given MSI-X IRQ.
- The PCI bus driver now stores more MSI-X state in a child's ivars.
Specifically, it now stores an array of IRQs (called "message vectors" in
the code) that have associated address and data values, and a small
virtual version of the MSI-X table that specifies the message vector
that a given MSI-X table entry uses. Sparse mappings are permitted in
the virtual table.
- The PCI bus driver now configures the MSI and MSI-X address/data
registers directly via custom bus_setup_intr() and bus_teardown_intr()
methods. pci_setup_intr() invokes PCIB_MAP_MSI() to determine the
address and data values for a given message as needed. The MD code
no longer has to call back down into the PCI bus code to set these
values from the nexus' bus_setup_intr() handler.
- The PCI bus code provides a callout (pci_remap_msi_irq()) that the MD
code can call to force the PCI bus to re-invoke PCIB_MAP_MSI() to get
new values of the address and data fields for a given IRQ. The x86
MSI code uses this when an MSI IRQ is moved to a different CPU, requiring
a new value of the 'address' field.
- The x86 MSI psuedo-driver loses a lot of code, and in fact the separate
MSI/MSI-X pseudo-PICs are collapsed down into a single MSI PIC driver
since the only remaining diff between the two is a substring in a
bootverbose printf.
- The PCI bus driver will now restore MSI-X state (including programming
entries in the MSI-X table) on device resume.
- The interface for pci_remap_msix() has changed. Instead of accepting
indices for the allocated vectors, it accepts a mini-virtual table
(with a new length parameter). This table is an array of u_ints, where
each value specifies which allocated message vector to use for the
corresponding MSI-X message. A vector of 0 forces a message to not
have an associated IRQ. The device may choose to only use some of the
IRQs assigned, in which case the unused IRQs must be at the "end" and
will be released back to the system. This allows a driver to use the
same remap table for different shortage values. For example, if a driver
wants 4 messages, it can use the same remap table (which only uses the
first two messages) for the cases when it only gets 2 or 3 messages and
in the latter case the PCI bus will release the 3rd IRQ back to the
system.
MFC after: 1 month
that the MSI mapping window is fixed at 0xfee00000 and the capability
does not include two more dwords used to program the address. Supporting
this mostly results in quieting spurious warnings during boot about
non-default MSI mapping windows.
- HT 2.00b also added a new HT capability type, so support that in pciconf.
MFC after: 3 days
Tested by: jmg
