when the CC is not set. Note NO_COUNTRY is set to 0xffff for now
(must be 16 bits as ieee80211_regdomain struct defines sku's and
cc's as uint16_t which may need fixing).
o do not require 1/2 and 1/4 rate channels be present in the
calibration list when doing a gsm regulatory change; the
existing 900MHz cards are not self-identifying so there is
no way (using the calibration channel list) to check
o store XML_Parser in the state block so we can report line numbers for errors
o complain about netband w/o mode
o complain about unknown modes
o complain about band w/o enclosing netband
o complain about duplicate freqband
o complain about unknown channel flags
o complain about band w/o freqband's
o complain about band w/o maxpower
o complain about country w/o ISO cc
o complain about country w/o regdomain reference
indicates if an association id is required before outbound traffic
is permitted. This cleans up the previous change that broke mcast
traffic "to the stack" in ap mode as a side effect.
Reviewed by: sephe, thompsa, weongyo
src into the tree. The old split was balanced on module dependencies
and symbol exposure that no longer exists. Users that want a module
setup with rate control algorithm other than sample must override
ATH_RATE in the ath module Makefile.
Reviewed by: imp
It includes the following fix:
2426. [bug] libbind: inet_net_pton() can sometimes return the
wrong value if excessively large netmasks are
supplied. [RT #18512]
Reported by: Maksymilian Arciemowicz <cxib__at__securityreason.com>
to keep for 7-STABLE when MFCing in_pcbladdr() to not change the
behaviour there.
With this a destination route via a loopback interface is treated as
a valid and reachable thing for IPv4 source address selection, even
though nothing of that network is ever directly reachable, but it is
more like a blackhole route.
With this the source address will be selected and IPsec can grab the
packets before we would discard them at a later point, encapsulate them
and send them out from a different tunnel endpoint IP.
Discussed on: net
Reported by: Frank Behrens <frank@harz.behrens.de>
Tested by: Frank Behrens <frank@harz.behrens.de>
MFC after: 4 weeks (just so that I get the mail)
reasonable close to and in the same format as it had always.
r185435 said it would try that but I had been living with jail
patches for too long to actually remember the single-line format
when adding backwards compatibility back in p4.
Reported by: Philipp Wuensche <cryx-freebsd@h3q.com>
Tested by: Philipp Wuensche <cryx-freebsd@h3q.com>
MFC after: 4 weeks (just for me to get the mail)
Remove ng_rmnode_flags() function.
ng_rmnode_self() was made to be called only while having node locked.
When node is properly locked, any function call sent to it will always be
queued. So turning ng_rmnode_self() into the ng_rmnode_flags() is not just
meaningless, but incorrent, as it violates node locking when called outside.
No objections: julian, thompsa
variable in this copy of the code[1].
While here prefix the variables with 'pf_' to avoid file static global
variables with colliding names that are or will be virtualized.
Discussed with: rwatson, silby [1]
by redoing the Open Firmware card initialization calls in ofwfb_set_mode(). This
uses the same trick (setting V_ADP_MODECHANGE) to arrange this as machfb(4) and
creatorfb(4).
but formerly missed under VIMAGE_GLOBAL.
Put the extern declarations of the virtualized globals
under VIMAGE_GLOBAL as the globals themsevles are already.
This will help by the time when we are going to remove the globals
entirely.
Sponsored by: The FreeBSD Foundation
might do subsequent reads from other providers. This stopped geli (and
probably other classes using g_metadata_store as well) from being put on top
of gvinum raid5 volumes.
Note:
The reason it fails in the gvinum raid5 case is that gvinum will read back the
old parity stripe before calculating the new parity stripe to be written out
again. The write will then fail because the underlying disk to be read is
opened write only.
MFC after: 1 week
time it is marked for user space callchain capture in the NMI
handler and the time the callchain capture callback runs.
- Improve code and control flow clarity by invoking hwpmc(4)'s user
space callchain capture callback directly from low-level code.
Reviewed by: jhb (kern/subr_trap.c)
Testing (various patch revisions): gnn,
Fabien Thomas <fabien dot thomas at netasq dot com>,
Artem Belevich <artemb at gmail dot com>
if (batt_sleep_ms)
AcpiOsSleep(1);
where the rest are all:
if (batt_sleep_ms)
AcpiOsSleep(batt_sleep_ms);
I can't recall why that one was different, so change it
to match the rest.
Pointed out by: Christoph Mallon
MFC after: 2 weeks
All ioctl()'s that aren't implemented by pts(4) are forwarded to the TTY
itself. Unfortunately this is not correct for FIONREAD, because it will
give the wrong amount of bytes that are available to read.
Tested by: keramida
Reminded by: keramida
On some laptops with smart batteries, enabling battery monitoring
software causes keystrokes from atkbd to be lost. This has also been
reported on Linux, and is apparently due to the keyboard and I2C line
for the battery being routed through the same chip. Whether that's
accurate or not, adding extra sleeps to the status checking code
causes the problem to go away.
I've been running this for nearly six months now on my laptop,
it works like a charm.
Reviewed by: Nate Lawson (in a previous revision)
MFC after: 2 weeks
