Don't use a struct if_irq for IFLIB_INTR_IOV type interrupts since that results
in get_core_offset() being called on them, and get_core_offset() doesn't
handle IFLIB_INTR_IOV type interrupts, which results in an assert() being triggered
in iflib_irq_set_affinity().
PR: 235730
Reported by: Jeffrey Pieper <jeffrey.e.pieper@intel.com>
MFC after: 1 day
Sponsored by: Intel Corporation
When pci_realloc_bars was first added, the intention was to eventually
enable it by default, but it was left disabled to preserve existing
behavior. The setting is pretty conservative in that it does not
attempt to allocate resources for BARs that the BIOS/firmware leaves
disabled. It only attempts to reallocate resources for a BAR that the
firmware programmed during boot but that conflicts with another
resource during the kernel's device scan.
PR 221350 is an example of a machine that this knob fixes.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D18965
The hardcoded ident is exactly 20 bytes long but sprintf adds terminating zero,
so there is one byte written out of array bounds.As a fix use strncpy it
appends \0 only if space allows and its behavior matches virtio spec:
When VIRTIO_BLK_T_GET_ID is issued, the device identifier, up to 20 bytes, is
written to the buffer. The identifier should be interpreted as an ascii string.
It is terminated with \0, unless it is exactly 20 bytes long.
PR: 202298
Reviewed by: br
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18852
r241119 that's performed globally by device_attach(9).
- As for the EM-class of devices, em(4) supports multiple queues
and MSI-X respectively only with 82574 devices. However, since
the conversion to iflib(4), em(4) relies on the interrupt type
fallback mechanism, i. e. MSI-X -> MSI -> INTx, of iflib(4) to
figure out the interrupt type to use for the EM-class (as well
as the IGB-class) of MACs. Moreover, despite the datasheet for
82583V not mentioning any support of MSI-X, there actually are
82583V devices out there that report a varying number of MSI-X
messages as supported. The interrupt type fallback of iflib(4)
is causing two failure modes depending on the actual number of
MSI-X messages supported for such instances of 82583V:
1) With only one MSI-X message supported, none is left for the
RX/TX queues as that one message gets assigned to the admin
interrupt. Worse, later on - which will be addressed with a
separate fix - iflib(4) interprets that one messages as MSI
or INTx to be set up, but fails to actually do so as it has
previously called pci_alloc_msix(9). [1, 2]
2) With more message supported, their distribution is okay but
then em_if_msix_intr_assign() doesn't work for 82583V, with
the interface being left in a non-working state, too. [3]
Thus, let em_if_attach_pre() indicate to iflib(4) to try MSI-X
with 82574 only, and at most MSI for the remainder of EM-class
devices.
While at it, remove "try_second_bar" as it's polarity inverted
and not actually needed.
- Remove code from em_if_timer() that effectively is a NOP since
the conversion to iflib(4) ("trigger" is no longer read).
While at it, let the comment for em_if_timer() reflect reality
after said conversion.
- Implement an ifdi_watchdog_reset method which only updates the
em(4) "watchdog_events" counter but doesn't perform any reset,
so that the em(4) "watchdog_timeouts" SYSCTL (iflib(4) doesn't
provide a counterpart) reflects reality and these timeouts add
to IFCOUNTER_OERRORS again after the iflib(4) conversion.
- Remove the "mbuf_defrag_fail" and "tx_dma_fail" SYSCTLS; since
the iflib(4) conversion, associated counters are disconnected,
but iflib(4) provides "mbuf_defrag_failed" and "tx_map_failed"
respectively as equivalents.
- Move the description preceding lem_smartspeed() to the correct
spot before em_reset() and bring back appropriate comments for
{igb,em}_initialize_rss_mapping() and lem_smartspeed() lost in
the iflib(4) conversion.
- Adapt some other function descriptions and INIT_DEBUGOUT() use
to match reality after the iflib(4) conversion.
- Put the debugging message of em_enable_vectors_82574() (missed
in r343578) under bootverbose, too.
PR: 219428 [1], 235246 [2], 235147 [3]
Reviewed by: erj (previous version)
Differential Revision: https://reviews.freebsd.org/D19108
When configured with more tx queues than rx queues,
em_if_msix_intr_assign() was incorrectly routing the tx event
interrupts.
Reviewed by: erj, marius
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19070
Use the information from IORT parsing to translate the PCI RID to
GIC ITS device ID. And similarly, use the information to find the
PIC XREF identifier to be used for PCI devices.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D18004
Add new file arm64/acpica/acpi_iort.c to support the "IO Remapping
Table" (IORT). The table is specified in ARM document "ARM DEN 0049D"
titled "IO Remapping Table Platform Design Document". The IORT table
has information on the associations between PCI root complexes, SMMU
blocks and GIC ITS blocks in the system.
The changes are to parse and save the information in the IORT table.
The API to use this information is added to sys/dev/acpica/acpivar.h.
The acpi_iort.c also has code to check the GIC ITS nodes seen in the
IORT table with corresponding entries in MADT table (for validity)
and with entries in SRAT table (for proximity information).
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D18002
There are few places in interrupt handler where the driver
lock is dropped; ensure that device is still running before
processing remaining ring entries.
PR: 192641
MFC after: 5 days
when TEKEN_CONS25 is configured. Fix this by adding a function to
set the flag that enables the fix and always calling this function
for syscons.
Expand the man page for teken_set_cons25(). This function is not
very useful since it can only set but not clear 1 flag. In practice,
it is only used when TEKEN_CONS25 is configured and all that does is
choose the the default emulation for syscons at compile time.
Changelist:
- Replace ND, D and RD macros with nm_prdis, nm_prinf, nm_prerr
and nm_prlim, to avoid possible naming conflicts.
- Add netmap_krings_mode_commit() helper function and use that
to reduce code duplication.
- Refactor pipes control code to export some functions that
can be reused by the veth driver (on Linux) and epair(4).
- Add check to reject API requests with version less than 11.
- Small code refactoring for the null adapter.
MFC after: 1 week
Use recent best practices for Copyright form at the top of
the license:
1. Remove all the All Rights Reserved clauses on our stuff. Where we
piggybacked others, use a separate line to make things clear.
2. Use "Netflix, Inc." everywhere.
3. Use a single line for the copyright for grep friendliness.
4. Use date ranges in all places for our stuff.
Approved by: Netflix Legal (who gave me the form), adrian@ (pmc files)
Add SYNC_KLOOP_MODE option, and add support for direct mode, where application
executes the TXSYNC and RXSYNC in the context of the ioeventfd wake up callback.
MFC after: 5 days
When in MSI mode, the device was only being configured with one
interrupt index, but it needs two - one for the actual interrupt and
one to park the tx queue at.
Also clarified comments relating to interrupt index assignment.
Reported by: Yuri Pankov <yuripv@yuripv.net>
MFC after: 1 day
"slow" interrupt handler:
- Expand the list of INT_CAUSE registers known to the driver.
- Add decode information for many more bits but decouple it from the
rest of intr_info so that it is entirely optional.
- Call t4_fatal_err exactly once, and from the top level PL intr handler.
t4_fatal_err:
- Use t4_shutdown_adapter from the common code to stop the adapter.
- Stop servicing slow interrupts after the first fatal one.
Driver/firmware interaction:
- CH_DUMP_MBOX: note whether the mailbox being dumped is a command or a
reply or something else.
- Log the raw value of pcie_fw for some errors.
- Use correct log levels (debug vs. error).
Sponsored by: Chelsio Communications
Not all child devices of the NVDIMM root device represent DIMM devices
which are present in the system. The spec says (ACPI 6.2, sec 9.20.2):
For each NVDIMM present or intended to be supported by platform,
platform firmware also exposes an NVDIMM device ... under the
NVDIMM root device.
Present NVDIMM devices are found by walking all of the NFIT table's
SPA ranges, then walking the NVDIMM regions mentioned by those SPA
ranges.
A set of NFIT walking helper functions are introduced to avoid the
need to splat the enumeration logic across several disparate
callbacks.
Submitted by: D Scott Phillips <d.scott.phillips@intel.com>
Sponsored by: Intel Corporation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18439
Move the enumeration of NVDIMM SPA ranges from the spa GEOM class
initializer into the NVDIMM root device. This will be necessary for a
later change where NVDIMM namespaces require NVDIMM device enumeration
to be reliably ordered before SPA enumeration.
Submitted by: D Scott Phillips <d.scott.phillips@intel.com>
Sponsored by: Intel Corporation
MFC after: 1 week
Differential revision: https://reviews.freebsd.org/D18734
This patch and commit message are based on r340256 created by Jacob Keller:
The iflib stack does not disable TSO automatically when TXCSUM is
disabled, instead assuming that the driver will correctly handle TSOs
even when CSUM_IP is not set.
This results in iflib calling ixgbe_isc_txd_encap with packets which have
CSUM_IP_TSO, but do not have CSUM_IP or CSUM_IP_TCP set. Because of
this, ixgbe_tx_ctx_setup will not setup the IPv4 checksum offloading.
This results in bad TSO packets being sent if a user disables TXCSUM
without disabling TSO.
Fix this by updating the ixgbe_tx_ctx_setup function to check both
CSUM_IP and CSUM_IP_TSO when deciding whether to enable checksums.
Once this is corrected, another issue for TSO packets is revealed. The
driver sets IFLIB_NEED_ZERO_CSUM in order to enable a work around that
causes the ip->sum field to be zero'd. This is necessary for ix
hardware to correctly perform TSOs.
However, if TXCSUM is disabled, then the work around is not enabled, as
CSUM_IP will not be set when the iflib stack checks to see if it should
clear the sum field.
Fix this by adding IFLIB_TSO_INIT_IP to the iflib flags for the ix and
ixv interface files.
Once both of these changes are made, the ix and ixv drivers should
correctly offload TSO packets when TSO offload is enabled, regardless
of whether TXCSUM is enabled or disabled.
Submitted by: Piotr Pietruszewski <piotr.pietruszewski@intel.com>
Reviewed by: IntelNetworking
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D18470
From Piotr:
This patch introduces adapter->task_requests register responsible for
recording requests for mod_task, msf_task, mbx_task, fdir_task and
phy_task calls. Instead of enqueueing these tasks with
GROUPTASK_ENQUEUE, handlers will be called directly from
ixgbe_if_update_admin_status() while holding ctx lock.
SIOCGIFXMEDIA ioctl() call reads adapter->media list. The list is
deleted and rewritten in ixgbe_handle_msf() task without holding ctx
lock. This change is needed to maintain data coherency when sharing
adapter info via ioctl() calls.
Patch co-authored by Krzysztof Galazka <krzysztof.galazka@intel.com>.
PR: 221317
Submitted by: Piotr Pietruszewski <piotr.pietruszewski@intel.com>
Reviewed by: sbruno@, IntelNetworking
Sponsored by: Intel Corporation
Differential Revision: https://reviews.freebsd.org/D18468
iflib is already a module, but it is unconditionally compiled into the
kernel. There are drivers which do not need iflib(4), and there are
situations where somebody might not want iflib in kernel because of
using the corresponding driver as module.
Reviewed by: marius
Discussed with: erj
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Differential revision: https://reviews.freebsd.org/D19041
copyright.
When all member nations of the Buenos Aires Convention adopted the Berne
Convention, the phrase "All rights reserved" became unnecessary to assert
copyright. Remove it from files under my or Panasas's copyright. The files
related to jedec_dimm(4) also bear avg@'s copyright; he has approved this
change.
Approved by: avg
Sponsored by: Panasas
When using poll(), select() or kevent() on netmap file descriptors,
netmap executes the equivalent of NIOCTXSYNC and NIOCRXSYNC commands,
before collecting the events that are ready. In other words, the
poll/kevent callback has side effects. This is done to avoid the
overhead of two system call per iteration (e.g., poll() + ioctl(NIOC*XSYNC)).
When the kqueue subsystem invokes the kqueue(9) f_event callback
(netmap_knrw), it holds the lock of the struct knlist object associated
to the netmap port (the lock is provided at initialization, by calling
knlist_init_mtx).
However, netmap_knrw() may need to wake up another netmap port (or even
the same one), which means that it may need to call knote().
Since knote() needs the lock of the struct knlist object associated to
the to-be-wake-up netmap port, it is possible to have a lock order reversal
problem (AB/BA deadlock).
This change prevents the deadlock by executing the knote() call in a
per-selinfo taskqueue, where it is possible to hold a mutex.
Reviewed by: aleksandr.fedorov_itglobal.com
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18956
bus_teardown_intr(9) before pci_release_msi(9).
- Ensure that iflib(4) and associated drivers pass correct RIDs to
bus_release_resource(9) by obtaining the RIDs via rman_get_rid(9)
on the corresponding resources instead of using the RIDs initially
passed to bus_alloc_resource_any(9) as the latter function may
change those RIDs. Solely em(4) for the ioport resource (but not
others) and bnxt(4) were using the correct RIDs by caching the ones
returned by bus_alloc_resource_any(9).
- Change the logic of iflib_msix_init() around to only map the MSI-X
BAR if MSI-X is actually supported, i. e. pci_msix_count(9) returns
> 0. Otherwise the "Unable to map MSIX table " message triggers for
devices that simply don't support MSI-X and the user may think that
something is wrong while in fact everything works as expected.
- Put some (mostly redundant) debug messages emitted by iflib(4)
and em(4) during attachment under bootverbose. The non-verbose
output of em(4) seen during attachment now is close to the one
prior to the conversion to iflib(4).
- Replace various variants of spelling "MSI-X" (several in messages)
with "MSI-X" as used in the PCI specifications.
- Remove some trailing whitespace from messages emitted by iflib(4)
and change them to consistently start with uppercase.
- Remove some obsolete comments about releasing interrupts from
drivers and correct a few others.
Reviewed by: erj, Jacob Keller, shurd
Differential Revision: https://reviews.freebsd.org/D18980
Effectively all i386 kernels now have two pmaps compiled in: one
managing PAE pagetables, and another non-PAE. The implementation is
selected at cold time depending on the CPU features. The vm_paddr_t is
always 64bit now. As result, nx bit can be used on all capable CPUs.
Option PAE only affects the bus_addr_t: it is still 32bit for non-PAE
configs, for drivers compatibility. Kernel layout, esp. max kernel
address, low memory PDEs and max user address (same as trampoline
start) are now same for PAE and for non-PAE regardless of the type of
page tables used.
Non-PAE kernel (when using PAE pagetables) can handle physical memory
up to 24G now, larger memory requires re-tuning the KVA consumers and
instead the code caps the maximum at 24G. Unfortunately, a lot of
drivers do not use busdma(9) properly so by default even 4G barrier is
not easy. There are two tunables added: hw.above4g_allow and
hw.above24g_allow, the first one is kept enabled for now to evaluate
the status on HEAD, second is only for dev use.
i386 now creates three freelists if there is any memory above 4G, to
allow proper bounce pages allocation. Also, VM_KMEM_SIZE_SCALE changed
from 3 to 1.
The PAE_TABLES kernel config option is retired.
In collaboarion with: pho
Discussed with: emaste
Reviewed by: markj
MFC after: 2 weeks
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D18894
