Sockets representing the TCP endpoints for iWARP connections are
allocated by the ibcore module. Before this revision they were closed
either by the ibcore module or the iw_cxgbe hardware driver depending on
the state transitions during connection teardown. This is error prone
and there were cases where both iw_cxgbe and ibcore closed the socket
leading to double-free panics. The fix is to let ibcore close the
sockets it creates and never do it in the driver.
- Use sodisconnect instead of soclose (preceded by solinger = 0) in the
driver to tear down an RDMA connection abruptly. This does what's
intended without releasing the socket's fd reference.
- Close the socket in ibcore when the iWARP iw_cm_id is destroyed. This
works for all kinds of sockets: clients that initiate connections,
listeners, and sockets accepted off of listeners.
Reviewed by: Steve Wise @ Open Grid Computing, hselasky@
MFC after: 3 days
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D9796
SBP-2 specification defined maximum CDB length as 12 bytes. Newer SBP-3
specification allows CDB of any size, but this driver is too old. Proper
solution would be to look on maximal ORB size supported by the target.
MFC after: 1 week
RSS hash type will be used to identify the CPU on to which, a receive packet
will be queued. This patch extracts the "RSS hash type" from the receive
completion and sends it to the stack.
Submitted by: Venkatkumar Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed by: shurd
Approved by: sbruno
MFC after: 1 week
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D9685
2. add sysctl to set pause frame parameters
3. increase max segs for TSO packets to BXE_TSO_MAX_SEGMENTS (32)
4. add debug messages for PHY
5. HW LRO support restricted to FreeBSD versions 8.x and above.
Submitted by:Vaishali.Kulkarni@cavium.com
MFC after:5 days
This is required for FDT's standard "reg-io-width" property
(similar to "reg-shift" property) found in many DTS files.
This fixes operation on Altera Arria 10 SOC Development Kit,
where standard ns8250 uart allows 4-byte access only.
Reviewed by: kan, marcel
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D9785
vm_map_lookup_done should only be called when the gntdev has finished poking at
the entry.
Reported by: alc
Reviewed by: alc
MFC after: 1 week
Sponsored by: Citrix Systems R&D
During acpi_cmbat_attach() the acpi_cmbat_init_battery() notification
handler is registered. It has been observed this notification handler
can be called instantly, before the attach routine has returned. In
the notification handler there is a call to device_is_attached() which
returns false. Because the softc is set we know an attach is in
progress and the fix is simply to wait and try again in this case.
Reviewed by: avg @
MFC after: 1 week
The pl011 UART has a 16 entry Tx FIFO and a 16 entry Rx FIFO that
have not been used so far. Update the driver to enable the FIFOs
and use them in transmit and receive.
Reviewed by: andrew
Differential Revision: https://reviews.freebsd.org/D8819
directly from the node.
- Use ni_txparms directly instead of calculating them manually every time
- Move M_EAPOL flag check upper; otherwise it may be skipped due to
'ucastrate' / 'mcastrate' check
- Use 'mgtrate' for control frames too (see ifconfig(8), mgtrate parameter)
- Add few more M_EAPOL checks where it was missing (zyd(4), ural(4),
urtw(4))
- Few unrelated cleanups
Tested with:
- Intel 6205 (iwn(4)), STA mode;
- WUSB54GC (rum(4)), HOSTAP mode + RTL8188EU (rtwn(4)), STA mode.
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9811
Its more important for SPI HBAs, as they don't support CDBs above 12 bytes.
The new error code makes CAM to fall back to alternative commands.
MFC after: 2 weeks
This allows to properly handle cases when target wants to receive or send
more data then initiator wants to send or receive. Previously in such
cases isp(4) returned CAM_DATA_RUN_ERR, while now it returns resid > 0.
MFC after: 2 weeks
This change removes limitation of single S/G list entry and limitation on
maximal I/O size, using multiple data transfers per I/O if needed. Also
it removes code duplication between send and receive paths, which are now
completely equal.
Convert PCIe hot plug support over to asking the firmware, if any, for
permission to use the HotPlug hardware. Implement pci_request_feature
for ACPI. All other host pci connections to allowing all valid feature
requests.
Sponsored by: Netflix
pcib_request_feature allows drivers to request the firmware (ACPI)
release certain features it may be using. ACPI normally manages things
like hot plug, advanced error reporting and other features until the
OS requests ACPI to relenquish control since it is taking over.
Sponsored by: Netflix
- Check return code from initialization path; otherwise, vap state
may be wrong after an error.
- Do not try to run iwn_stop() / iwn_init() multiple times.
- Merge iwn_radio_on/off() and move RFKILL bit check into the task.
- Try to handle possible RF switch state change in S3 state (PR 181694).
PR: 181694
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D9797
On Core2 and older Intel CPUs, where TSC stops in C2, system does not
allow C2 entrance if timecounter hardware is TSC. This is done by
tc_windup() which tests for TC_FLAGS_C2STOP flag of the new
timecounter and increases cpu_disable_c2_sleep if flag is set. Right
now init_TSC_tc() only sets the flag if cpu_deepest_sleep >= 2, but
TSC is initialized too early for this variable to be set by
acpi_cpu.c.
There is no reason to require that ACPI reported C2 and deeper states
to set TC_FLAGS_C2STOP, so remove cpu_deepest_sleep test from
init_TSC_tc() condition. And since this is the only use of the
variable, remove it at all.
Reported and submitted by: Jia-Shiun Li <jiashiun@gmail.com>
Suggested by: jhb
MFC after: 2 weeks
* Uses the IWM_FW_PAGING_BLOCK_CMD firmware command to tell the firmware
what memory ranges to use for paging.
Obtained from: dragonflybsd.git 8a5b199964f8e7bdb00039f0b48817a01b402f18
VXGE_DEFAULT_TTI_RTIMER_VAL and VXGE_DEFAULT_RTI_RTIMER_VAL have value
zero but nevertheless we should use the right value on each.
Pointed by: jhb
X-MFC with: r314145
One test was inadvertently expecting a bug in the kernel's sscanf
implementation circa 2012. I don't know when that bug got fixed.
Reported by: royger
Reviewed by: royger
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9766
Most of these are null pointer dereferences or missing error checks in the
unit tests. One is a missing error check in xnb_attach_failed. None can
cause real problems in running systems.
Reported by: Coverity
CIDs: 1092469 1092468 1092467 2092466 1092465 1092512 1092511 1092510
CIDs: 1092510 1092509 1092508 1092507
Reviewed by: royger
MFC after: 3 weeks
Sponsored by: Spectra Logic Corp
Differential Revision: https://reviews.freebsd.org/D9234
The code is not operational right now so just comment away an obviously
useless assignment. Fix some typos while here.
Found with: coccinelle (da.cocci)
The Xen grant table device treats the mmap offset parameter as an unsigned
type, and as so it must use the newly introduced UOFF_TO_IDX.
Sponsored by: Citrix Systems R&D
MFC after: 2 weeks
X-MFC-with: r313690
with geom_flashmap(4) and teach it about MMC for slicing enhanced
user data area partitions. The FDT slicer still is the default for
CFI, NAND and SPI flash on FDT-enabled platforms.
- In addition to a device_t, also pass the name of the GEOM provider
in question to the slicers as a single device may provide more than
provider.
- Build a geom_flashmap.ko.
- Use MODULE_VERSION() so other modules can depend on geom_flashmap(4).
- Remove redundant/superfluous GEOM routines that either do nothing
or provide/just call default GEOM (slice) functionality.
- Trim/adjust includes
Submitted by: jhibbits (RouterBoard bits)
Reviewed by: jhibbits
Note that the timer itself fully supports suspension, but due to the lack of
ordering during the resume process FreeBSD cannot guarantee that the timer is
resumed before any device attempts to use it.
Submitted by: Liuyingdong <liuyingdong@huawei.com>
Reviewed by: royger
Differential Revision: https://reviews.freebsd.org/D9639
