little/big endian fashion, so that network drivers can just reference
the standard implementation and don't have to bring their own.
As discussed on arch@.
Obtained from: NetBSD
1. rt_check() cleanup:
rt_check() is only necessary for some address families to gain access
to the corresponding arp entry, so call it only in/near the *resolve()
routines where it is actually used -- at the moment this is
arpresolve(), nd6_storelladdr() (the call is embedded here),
and atmresolve() (the call is just before atmresolve to reduce
the number of changes).
This change will make it a lot easier to decouple the arp table
from the routing table.
There is an extra call to rt_check() in if_iso88025subr.c to
determine the routing info length. I have left it alone for
the time being.
The interface of arpresolve() and nd6_storelladdr() now changes slightly:
+ the 'rtentry' parameter (really a hint from the upper level layer)
is now passed unchanged from *_output(), so it becomes the route
to the final destination and not to the gateway.
+ the routines will return 0 if resolution is possible, non-zero
otherwise.
+ arpresolve() returns EWOULDBLOCK in case the mbuf is being held
waiting for an arp reply -- in this case the error code is masked
in the caller so the upper layer protocol will not see a failure.
2. arpcom untangling
Where possible, use 'struct ifnet' instead of 'struct arpcom' variables,
and use the IFP2AC macro to access arpcom fields.
This mostly affects the netatalk code.
=== Detailed changes: ===
net/if_arcsubr.c
rt_check() cleanup, remove a useless variable
net/if_atmsubr.c
rt_check() cleanup
net/if_ethersubr.c
rt_check() cleanup, arpcom untangling
net/if_fddisubr.c
rt_check() cleanup, arpcom untangling
net/if_iso88025subr.c
rt_check() cleanup
netatalk/aarp.c
arpcom untangling, remove a block of duplicated code
netatalk/at_extern.h
arpcom untangling
netinet/if_ether.c
rt_check() cleanup (change arpresolve)
netinet6/nd6.c
rt_check() cleanup (change nd6_storelladdr)
- use ifp instead if &ac->ac_if in a couple of nd6* calls;
this removes a useless dependency.
- use IFP2AC(ifp) instead of an extra variable to point to the struct arpcom;
this does not remove the nesting dependency between arpcom and ifnet but
makes it more evident.
there so there are no ABI changes);
+ replace 5 redefinitions of the IPF2AC macro with one in if_arp.h
Eventually (but before freezing the ABI) we need to get rid of
struct arpcom (initially with the help of some smart #defines
to avoid having to touch each and every driver, see below).
Apart from the struct ifnet, struct arpcom now only stores a copy
of the MAC address (ac_enaddr, but we already have another copy in
the struct ifnet -- if_addrhead), and a netgraph-specific field
which is _always_ accessed through the ifp, so it might well go
into the struct ifnet too (where, besides, there is already an entry
for AF_NETGRAPH data...)
Too bad ac_enaddr is widely referenced by all drivers. But
this can be fixed as follows:
#define ac_enaddr ac_if.the_original_ac_enaddr_in_struct_ifnet
(note that the right hand side would likely be a pointer rather than
the base address of an array.)
+ struct ifnet: remove unused fields, move ipv6-related field close
to each other, add a pointer to l3<->l2 translation tables (arp,nd6,
etc.) for future use.
+ struct route: remove an unused field, move close to each
other some fields that might likely go away in the future
ifp is now passed explicitly to ether_demux; no need to look it up again.
Make mtag a global var in ip_input.
Noticed by: rwatson
Approved by: bms(mentor)
them mostly with packet tags (one case is handled by using an mbuf flag
since the linkage between "caller" and "callee" is direct and there's no
need to incur the overhead of a packet tag).
This is (mostly) work from: sam
Silence from: -arch
Approved by: bms(mentor), sam, rwatson
Short description of ip_fastforward:
o adds full direct process-to-completion IPv4 forwarding code
o handles ip fragmentation incl. hw support (ip_flow did not)
o sends icmp needfrag to source if DF is set (ip_flow did not)
o supports ipfw and ipfilter (ip_flow did not)
o supports divert, ipfw fwd and ipfilter nat (ip_flow did not)
o returns anything it can't handle back to normal ip_input
Enable with sysctl -w net.inet.ip.fastforwarding=1
Reviewed by: sam (mentor)
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
a minor conflict):
o Use ETHER_ADDR_LEN in preference to '6'.
o Remove two unnecessary (caddr_t) casts. One of them causes problems in
my tree where etherbroadcastaddr is const, and (caddr_t) casts the const
away.
from the network interface earlier in ether_input(). At some point
(no fingers pointed), things were restructured and the labeling operation
moved later. This wasn't a problem as BPF_MTAP() relies on the ifnet
label not the mbuf label, but there might have been other problems.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
drain routines are done by swi_net, which allows for better queue control
at some future point. Packets may also be directly dispatched to a netisr
instead of queued, this may be of interest at some installations, but
currently defaults to off.
Reviewed by: hsu, silby, jayanth, sam
Sponsored by: DARPA, NAI Labs
the mbuf allocator flags {M_TRYWAIT, M_DONTWAIT}.
o Fix a bpf_compat issue where malloc() was defined to just call
bpf_alloc() and pass the 'canwait' flag(s) along. It's been changed
to call bpf_alloc() but pass the corresponding M_TRYWAIT or M_DONTWAIT
flag (and only one of those two).
Submitted by: Hiten Pandya <hiten@unixdaemons.com> (hiten->commit_count++)
bridge.c nor if_ethersubr.c depend on IPFIREWALL.
Restore the use of fw_one_pass in if_ethersubr.c
ipfw.8 will be updated with a separate commit.
Approved by: re
ether_header; instead drivers are to leave the Ethernet header at the
front of the packet
o add declarations for netgraph and vlan hooks that were removed from ethernet.h
o change various in-file calling conventions to track change in input API
o fixup bridge support to handle Ethernet header no longer being stripped
o add consistency checks to ether_input to catch problems with the change
in the API; some of these may want to be moved to #ifdef DIAGNOSTIC at a
later time (though they are not too expensive to leave as is)
o change ether_demux to eliminate the passing of the Ethernet header; it is
now expected at the front of the packet a la ether_input
o add ether_sprintf compatibility shim
o change ether_ifattach API to remove "bpf supported param" and add a pointer
to the MAC address to be installed for the LL address (this is for future
changes to divest struct arpcom from struct ifnet)
o change ether_ifdetach API to remove "bpf support param"
Reviewed by: many
Approved by: re
Setting this flag on an ethernet interface blocks transmission of packets
and discards incoming packets after BPF processing.
This is useful if you want to monitor network trafic but not interact
with the network in question.
Sponsored by: http://www.babeltech.dk
