case if memory allocation failed.
- Remove fourth argument from VLAN_INPUT_TAG(), that was used
incorrectly in almost all drivers. Indicate failure with
mbuf value of NULL.
In collaboration with: yongari, ru, sam
in the 802.11 layer: we send a directed probe request frame to the
current ap bmiss_max times (w/o answer) before scanning for a new ap.
MFC after: 2 weeks
o plug memory leak in adhoc mode: on rx the sender may be the
current master so simply checking against ic_bss is not enough
to identify if the packet comes from an unknown sender; must
also check the mac address
o split neighbor node creation into two routines and fillin state
of nodes faked up on xmit when a beacon or probe response frame
is later received; this ensures important state like the rate set
and advertised capabilities are correct
Obtained from: netbsd
MFC after: 1 week
o add ic_curchan and use it uniformly for specifying the current
channel instead of overloading ic->ic_bss->ni_chan (or in some
drivers ic_ibss_chan)
o add ieee80211_scanparams structure to encapsulate scanning-related
state captured for rx frames
o move rx beacon+probe response frame handling into separate routines
o change beacon+probe response handling to treat the scan table
more like a scan cache--look for an existing entry before adding
a new one; this combined with ic_curchan use corrects handling of
stations that were previously found at a different channel
o move adhoc neighbor discovery by beacon+probe response frames to
a new ieee80211_add_neighbor routine
Reviewed by: avatar
Tested by: avatar, Michal Mertl
MFC after: 2 weeks
o separate configured beacon interval from listen interval; this
avoids potential use of one value for the other (e.g. setting
powersavesleep to 0 clobbers the beacon interval used in hostap
or ibss mode)
o bounds check the beacon interval received in probe response and
beacon frames and drop frames with bogus settings; not clear
if we should instead clamp the value as any alteration would
result in mismatched sta+ap configuration and probably be more
confusing (don't want to log to the console but perhaps ok with
rate limiting)
o while here up max beacon interval to reflect WiFi standard
Noticed by: Martin <nakal@nurfuerspam.de>
MFC after: 1 week
when operating in ap mode. Previously we allocated a node from the
station table, sent the frame (using the node), then released the
reference that "held the frame in the table". But while the frame
was in flight the node might be reclaimed which could lead to
problems. The solution is to add an ieee80211_tmp_node routine
that crafts a node that does exist in a table and so isn't ever
reclaimed; it exists only so long as the associated frame is in flight.
MFC after: 5 days
o add ic_flags_ext for eventual extention of ic_flags
o define/reserve flag+capabilities bits for superg,
bg scan, and roaming support
o refactor debug msg macros
MFC after: 3 days
don't mark the MORE_DATA bit when taking it off the ps queue, there's
no 802.11 header then; we must wait to do this at encap time so
mark the mbuf instead.
Reviewed by: avatar
Approved by: re (scottl)
Obtained from: Atheros
stations in ap mode. Track when a node's first auth frame is
received and use this to decide whether or not to bump the refcnt.
This insures we only ever bump the refcnt once.
Reviewed by: avatar
Approved by: re (scottl)
This fixes duplicative BSS entries(memory leaks as well) listed in
"ifconfig dev list scan" when a station fails to associate with an AP.
Reviewed by: sam
Approved by: re (scottl)
it; instead pass the space occupied by the header down into the
crypto modules (except in the demic case which needs it only when
doing int in s/w)
o while here fix defrag to strip the header from 2nd and later frames
o teach decap code how to handle 4-address frames
