support the CM-battery interface. Smart batteries can eventually be
supported without ACPI via a separate SMBus interface. The ACPI interface
uses the embedded controller for reading/writing to the SMBus, and normal
ASL definitions for locating the battery controller (since SMBus can't be
enumerated.) Also import definitions for the smart battery interface.
This was written by Hans Petter Selasky with minor cleanups from myself.
Submitted by: Hans Petter Selasky <hselasky / c2i.net>
* Use ACPI_BATT_UNKNOWN instead of constants
* Use maxunit instead of a count of devices since we may have sparse
battery devices in the future. Only userland should be using unit
numbers anyway, so provide a translation function. (Kernel use of
batteries should be restricted to looking up a device_t and calling
methods directly.
* Don't check acpi_BatteryIsPresent() in acpi_battery. Leave it up to
the hardware-specific driver (i.e. cmbat) since smart batteries seem
to not report the "battery present" flag.
* Convert mA to mW if the battery uses those units. CM-batteries only
used mW so this deficiency went unnoticed.
* Clean strings reported in the battery info from any control chars.
* Only dereference the unit from ioctl_arg if the full struct is present.
Unit wouldn't have been used later if it wasn't present but this is
cleaner. Translate the unit if it's not ACPI_BATTERY_ALL_UNITS.
* bzero structs before returning them to usermode for future compat.
Most of this work was submitted by Hans Petter Selasky and then majorly
reworked by myself.
Submitted by: Hans Petter Selasky <hselasky / c2i.net>
vm_object_backing_scan() was not written to handle. Specifically, a wired
page within a backing object that is shadowed by a page within the shadow
object. Handle this state by removing the wired page from the backing
object. The wired page will be freed by socow_iodone().
Stop masking errors: If a page is being freed by vm_object_backing_scan(),
assert that it is no longer mapped rather than quietly destroying any
mappings.
Tested by: Harald Schmalzbauer
too. This fixes problem when connected prefixes overlap.
Obtained from: OpenBSD (rev. 1.40 by claudio);
[ I came to this fix myself, and then found out that
OpenBSD had already fixed it the same way.]
attach routine. Go ahead and ask for it in the probe routine and be
just as wrong as all the other cards that ask for it there...
# this gets the RTL8019 on a SBC at work fully functional. 6.0 still treats
# the 8019 as a generic NE-2000, so these changes aren't relevant there.
This avoids the need for sched_bind() in the default case so that you
can start up the NDIS subsystem at boot time when only CPU 0 is running.
There are potentially ways to fix it so that the DPC threads aren't
started until after the other CPUs are launched, but doing it correctly
is tricky. You need to defer the startup of the ntoskrnl subsystem
(ntoskrnl_libinit()), not just defer ndis_attach().
For now, I don't think it will make much difference having just the
single DPC thread (I started out with just one anyway). Note that this
turns the KeSetTargetProcessorDpc() routine into a no-op, since the
CPU number in struct kdpc is now ignored.
ed_probe_rtl80x9. In the pci case we call ed_probe_rtl80x9 first. In
the PCI case we were using the correct nic_offset by accident because
softc is initialized to zero. In the isa case we were using the wrong
value by accident, since ed_probe_WD80x3 sets the offset value to
0x10. This lead to the identification routines failing. Fix this
problem by always initalizing the nic_offset and asic_offset before
making ed_{asic,nic}_{in,out}* calls.
get a new pv under high system load where the available pv entries
have been exhausted before the pagedaemon has a chance to wake up
to reclaim some.
Prior to this, the NULL pointer dereference ended up causing
secondary panics with rather less than useful resulting tracebacks.
Reviewed by: alc, jhb
MFC after: 1 week
in reiserfs_lookup() that was used to fix an actual race in
ufs_lookup.c:1.78. This is not currently a hazard, but the
bug would be activated by marking reiserfs as MPSAFE.
Reviewed by: mux (mentor)
MFC after: 2 weeks
is KeRaiseIrql(newirql, &oldirql), not oldirql = KeRaiseIrql(newirql).
(The macro ultimately translates to KfRaiseIrql() which does use
the latter API, so this has no effect on generated code.)
Also, wait for thread termination the right way: kthread_exit()
will ultimately do a wakeup(td->td_proc). This is the event we
should wait on. Eliminate the previous synchronization machinery
for this since it was never guaranteed to work correctly.
to (max block - 1) * bsize. For DEV_BSIZE, this doubles the limit from
0.5 TB to 1 TB. For the old 4.4 FFS case, decrease the limit from 0.5 TB
to 2 GB - 1. Older systems had a 32 bit off_t so they couldn't access the
larger files anyway.
Collaboration with: bde
processor, to insure DPC thread 0 runs on CPU0, DPC thread 1 runs on
CPU1, and so on.
Elevate the priority of the workitem threads, though don't use as
high a priority as the DPC threads.
available kernel malloc types. Quite useful for post-mortem debugging of
memory leaks without a dump device configured on a panicked box.
MFC after: 2 weeks
version has a bug where it fails to properly cancel the polling loop
that periodically queries the BSSID (this is done to detect the
association/disassociation state). The timeout is supposed to fire
once a second, but the eloop_cancel_timeout() call uses a different
'user data' value than what was passed to eloop_register_timeout(),
so cancelling the timeouts fails. This results in an additional timeout
being created each time an EAPOL packet is received, which can lead
to dozens of unwanted timeouts firing every second instead of just one.
