ip_reass() expects IPv4 packet and will just corrupt any IPv6 packets
that it gets. Until proper IPv6 fragments handling function will be
implemented, pass IPv6 packets to next rule.
PR: 170604
MFC after: 1 week
The lookup_host() helper subroutine emits a struct in_addr value in network
byte order via caller passed pointer. However, the table value is expected
to be stored in host byte order. On little-endian machines, this produced a
reversed endian table value for Legacy or IPv4 table types when the value
was a hostname (instead of a plain IP address).
Fix by using ntohl() on the output 32-bit address.
While here, avoid some aliasing violations by storing the lookup_host()
output in an intermediate object of the correct type.
PR: 226429
Reported by: bugs.freebsd.org AT mx.zzux.com (also: Tested by)
Security: ipfw hostname table rules could potentially not act as admin intended
Sponsored by: Dell EMC Isilon
After consultation with SPDX experts and their matching guidelines[1],
the licensing doesn't exactly match the BSD-2-Clause. It yet remains to be
determined if they are equivalent or if there is a recognized license that
matches but it is safer to just revert the tags.
Let this also be a reminder that on FreeBSD, SPDX tags are only advisory
and have no legal value (but IANAL).
Pointyhat to: pfg
Thanks to: Rodney Grimes, Gary O'Neall
[1] https://spdx.org/spdx-license-list/matching-guidelines
This is similar to the TCP case. where a TCP RST segment can be sent.
There is one limitation: When sending an ABORT in response to an incoming
packet, it should be tested if there is no ABORT chunk in the received
packet. Currently, it is only checked if the first chunk is an ABORT
chunk to avoid parsing the whole packet, which could result in a DOS attack.
Thanks to Timo Voelker for helping me to test this patch.
Reviewed by: bcr@ (man page part), ae@ (generic, non-SCTP part)
Differential Revision: https://reviews.freebsd.org/D13239
The module is designed for modification of a packets of any protocols.
For now it implements only TCP MSS modification. It adds the external
action handler for "tcp-setmss" action.
A rule with tcp-setmss action does additional check for protocol and
TCP flags. If SYN flag is present, it parses TCP options and modifies
MSS option if its value is greater than configured value in the rule.
Then it adjustes TCP checksum if needed. After handling the search
continues with the next rule.
Obtained from: Yandex LLC
MFC after: 2 weeks
Relnotes: yes
Sponsored by: Yandex LLC
No objection from: #network
Differential Revision: https://reviews.freebsd.org/D10150
This opcode can be used to attach some data to external action opcode.
And unlike to O_EXTERNAL_INSTANCE opcode, this opcode does not require
creating of named instance to pass configuration arguments to external
action handler. The data is coming just next to O_EXTERNAL_ACTION opcode.
The userlevel part currenly supports formatting for opcode with ipfw_insn
size, by default it expects u16 numeric value in the arg1.
Obtained from: Yandex LLC
MFC after: 2 weeks
Sponsored by: Yandex LLC
Since the state name is an optional argument, it often can conflict
with other options. To avoid ambiguity now the state name must be
prefixed with a colon.
Obtained from: Yandex LLC
MFC after: 2 week
Sponsored by: Yandex LLC
is a 32-bit socklen_t, do_get3() passes the kernel to access the wrong
32-bit half on big-endian LP64 machines when simply casting the 64-bit
size_t optlen to a socklen_t pointer.
While at it and given that the intention of do_get3() apparently is to
hide/wrap the fact that socket options are used for communication with
ipfw(4), change the optlen parameter of do_set3() to be of type size_t
and as such more appropriate than uintptr_t, too.
MFC after: 3 days
The module works together with ipfw(4) and implemented as its external
action module.
Stateless NAT64 registers external action with name nat64stl. This
keyword should be used to create NAT64 instance and to address this
instance in rules. Stateless NAT64 uses two lookup tables with mapped
IPv4->IPv6 and IPv6->IPv4 addresses to perform translation.
A configuration of instance should looks like this:
1. Create lookup tables:
# ipfw table T46 create type addr valtype ipv6
# ipfw table T64 create type addr valtype ipv4
2. Fill T46 and T64 tables.
3. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
4. Create NAT64 instance:
# ipfw nat64stl NAT create table4 T46 table6 T64
5. Add rules that matches the traffic:
# ipfw add nat64stl NAT ip from any to table(T46)
# ipfw add nat64stl NAT ip from table(T64) to 64:ff9b::/96
6. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Stateful NAT64 registers external action with name nat64lsn. The only
one option required to create nat64lsn instance - prefix4. It defines
the pool of IPv4 addresses used for translation.
A configuration of instance should looks like this:
1. Add rule to allow neighbor solicitation and advertisement:
# ipfw add allow icmp6 from any to any icmp6types 135,136
2. Create NAT64 instance:
# ipfw nat64lsn NAT create prefix4 A.B.C.D/28
3. Add rules that matches the traffic:
# ipfw add nat64lsn NAT ip from any to A.B.C.D/28
# ipfw add nat64lsn NAT ip6 from any to 64:ff9b::/96
4. Configure DNS64 for IPv6 clients and add route to 64:ff9b::/96
via NAT64 host.
Obtained from: Yandex LLC
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6434
Now zero value of arg1 used to specify "tablearg", use the old "tablearg"
value for "nat global". Introduce new macro IP_FW_NAT44_GLOBAL to replace
hardcoded magic number to specify "nat global". Also replace 65535 magic
number with corresponding macro. Fix typo in comments.
PR: 211256
Tested by: Victor Chernov
MFC after: 3 days
Zero fib is correct value and it conflicts with IP_FW_TARG.
Use bprint_uint_arg() only when opcode contains IP_FW_TARG,
otherwise just print numeric value with cleared high-order bit.
MFC after: 3 days
setdscp's argument can have zero value that conflicts with IP_FW_TARG value.
Always set high-order bit if parser doesn't find tablearg keyword.
MFC after: 3 days
so when user did `ipfw table N flush` it always worked, but now
when table N doesn't exist the kernel returns ESRCH error.
This isn't fatal error for flush and destroy commands. Do not
call err(3) when errno is equal to ESRCH. Also warn only when
quiet mode isn't enabled. This fixes a regression in behavior,
when old rules are loaded from file.
Also use correct value for switch in the table_swap().
Reported by: Kevin Oberman
MFC after: 3 days
The keep-state, limit and check-state now will have additional argument
flowname. This flowname will be assigned to dynamic rule by keep-state
or limit opcode. And then can be matched by check-state opcode or
O_PROBE_STATE internal opcode. To reduce possible breakage and to maximize
compatibility with old rulesets default flowname introduced.
It will be assigned to the rules when user has omitted state name in
keep-state and check-state opcodes. Also if name is ambiguous (can be
evaluated as rule opcode) it will be replaced to default.
Reviewed by: julian
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6674
as defined in RFC 6296. The module works together with ipfw(4) and
implemented as its external action module. When it is loaded, it registers
as eaction and can be used in rules. The usage pattern is similar to
ipfw_nat(4). All matched by rule traffic goes to the NPT module.
Reviewed by: hrs
Obtained from: Yandex LLC
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D6420
Centre for Advanced Internet Architectures
Implementing AQM in FreeBSD
* Overview <http://caia.swin.edu.au/freebsd/aqm/index.html>
* Articles, Papers and Presentations
<http://caia.swin.edu.au/freebsd/aqm/papers.html>
* Patches and Tools <http://caia.swin.edu.au/freebsd/aqm/downloads.html>
Overview
Recent years have seen a resurgence of interest in better managing
the depth of bottleneck queues in routers, switches and other places
that get congested. Solutions include transport protocol enhancements
at the end-hosts (such as delay-based or hybrid congestion control
schemes) and active queue management (AQM) schemes applied within
bottleneck queues.
The notion of AQM has been around since at least the late 1990s
(e.g. RFC 2309). In recent years the proliferation of oversized
buffers in all sorts of network devices (aka bufferbloat) has
stimulated keen community interest in four new AQM schemes -- CoDel,
FQ-CoDel, PIE and FQ-PIE.
The IETF AQM working group is looking to document these schemes,
and independent implementations are a corner-stone of the IETF's
process for confirming the clarity of publicly available protocol
descriptions. While significant development work on all three schemes
has occured in the Linux kernel, there is very little in FreeBSD.
Project Goals
This project began in late 2015, and aims to design and implement
functionally-correct versions of CoDel, FQ-CoDel, PIE and FQ_PIE
in FreeBSD (with code BSD-licensed as much as practical). We have
chosen to do this as extensions to FreeBSD's ipfw/dummynet firewall
and traffic shaper. Implementation of these AQM schemes in FreeBSD
will:
* Demonstrate whether the publicly available documentation is
sufficient to enable independent, functionally equivalent implementations
* Provide a broader suite of AQM options for sections the networking
community that rely on FreeBSD platforms
Program Members:
* Rasool Al Saadi (developer)
* Grenville Armitage (project lead)
Acknowledgements:
This project has been made possible in part by a gift from the
Comcast Innovation Fund.
Submitted by: Rasool Al-Saadi <ralsaadi@swin.edu.au>
X-No objection: core
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D6388
objects with the same name in different sets.
Add optional manage_sets() callback to objects rewriting framework.
It is intended to implement handler for moving and swapping named
object's sets. Add ipfw_obj_manage_sets() function that implements
generic sets handler. Use new callback to implement sets support for
lookup tables.
External actions objects are global and they don't support sets.
Modify eaction_findbyname() to reflect this.
ipfw(8) now may fail to move rules or sets, because some named objects
in target set may have conflicting names.
Note that ipfw_obj_ntlv type was changed, but since lookup tables
actually didn't support sets, this change is harmless.
Obtained from: Yandex LLC
Sponsored by: Yandex LLC
