through a voltage divisor (R163 and R164 on page 4 of BBB schematic).
Add a note about this on ti_adc(4) man page. The ti_adc(4) man page will
first appear on 10.1-RELEASE.
MFC after: 1 week
Suggested by: Sulev-Madis Silber (ketas)
Manual page reviewed by: brueffer (D127)
from the slave (for example, when master is failing on disk IO and could not be
logged into or execute cronjob).
Commented out examples changed too to simplify future merging.
Idea by: kaa@zvuki.ru
Discussed with: glebius
MFC after: 1 week
We should not be leaking these interfaces to the outside world given
that it's much easier for third-party components to use the devel/atf
package from ports.
As a side-effect, we can also drop the ATF pkgconfig and aclocal files
from the base system. Nothing in the base system needs these, and it
was quite ugly to have to get them installed only so that a few ports
could build. The offending ports have been fixed to depend on
devel/atf explicitly.
Reviewed by: bapt
Makefiles are evaluated without building things. In a normal build,
the prerequisites would be built, and CC would be an actual thing. In
an INDEX build, though, they don't exists. Redirect stderr to get rid
of annoying messages, and assume that the compiler version is 0 if the
actual compiler can't tell us. Do this in preference to guessing based
on numbers because gcc410 might be 4.10, or 4.1.0 and without
carefully crafted special knowledge we differentiate between them
easily (also ming-gcc has no clues at all). Elsewhere, don't trust
the compiler version if it is 0.
ismt(4) supports the SMBus Message Transport controller found on Intel
C2000 series (Avoton) and S1200 series (Briarwood) Atom SoCs.
Sponsored by: Intel
this allows make -n to do tree walks as expected without
doing anything else (as intended).
Use prefix _sub. to help avoid conflict with any real target.
Reviewed by: imp
Targets thus marked are supposed to run even with -n.
As such they should not do anything except run the sub-make.
Use an intermediate target _* to associate with _SUBDIR and which
depends on installincludes etc so that we get the correct behavior with -n.
Reviewed by: marcel
This is not a comprehensive list, as the variables themselves are spread
out over multiple files, but it is a start.
Add a section to make.conf noting that variables may be set there that
affect ports builds, but refer to ports.7 and elsewhere for the actual
listing; any listing in make.conf.5 would likely become out of date
fairly quickly.
PR: docs/189199
Reviewed by: bdrewery (previous version)
Approved by: hrs (mentor)
src/sys and the rest of the tree for builds.
o eliminate including bsd.mkopts.mk for the moment in kern.opts.mk
o No need to include src.opts.mk at all anymore. The reasons for it
are now coverted in sys.mk and src.sys.mk.
and MK_LLDB=no, so set those explicitly (now that we can do
that). Simplify tests for these variables as well, since we know they
will always be defined regardless of the phase of the build.
with clang 3.3. Useful for test building -current on a -stable system
in individual directories. Potentially useful if we ever want to
support, say, gcc 4.8 or 4.9's new warnings when building with an
external toolchain (but such support not yet committed). Document
the bsd.compiler.mk interface.
install it as fmake. This defaults to no. This should be viewed as the
first step towards evental migration of this historic code to ports
and removal from the tree.
This driver supports the low and high precision models (9 and 11 bits) and
it will auto-detect the both variants.
The driver expose the temperature registers (actual temperature, shutdown
and hysteresys temperature) and also the configuration register.
It was tested on FDT systems: RPi, BBB and on non-FDT systems: AR71xx, with
both, hardware i2c controllers (when available) and gpioiic(4).
This provides a simple and cheap way for verifying the i2c bus on embedded
systems.
