INADDR_NONE: Incoming packets go to the alias address (the default)
INADDR_ANY: Incoming packets are not NAT'd (direct access to the
internal network from outside)
anything else: Incoming packets go to the specified address
Change a few inaddr::s_addr == 0 to inaddr::s_addr == INADDR_ANY
while I'm there.
redirected and when no target address has been specified, NAT
the destination address to the alias address rather than
allowing people direct access to your internal network from
outside.
mbuf is marked for delayed checksums, then additionally mark the
packet as having it's checksums computed. This allows us to bypass
computing/checking the checksum entirely, which isn't really needeed
as the packet has never hit the wire.
Reviewed by: green
Reported in Usenet by: locke@mcs.net (Peter Johnson)
While i was at it, prepended a 0x to the %D output, to make it clear that
the printed value is in hex (i assume %D has been chosen over %#x to
obey network byte order).
improperly doing the equivalent of (m = (function() == NULL)) instead
of ((m = function()) == NULL).
This fixes a NULL pointer dereference panic with runt arp packets.
Remove a bogus (redundant, just weird, etc.) key_freeso(so).
There are no consumers of it now, nor does it seem there
ever will be.
in6?_pcb.c:
Add an if (inp->in6?p_sp != NULL) before the call to
ipsec[46]_delete_pcbpolicy(inp). In low-memory conditions
this can cause a crash because in6?_sp can be NULL...
from iso88025.h.
o Add minimal llc support to iso88025_input.
o Clean up most of the source routing code.
* Submitted by: Nikolai Saoukh <nms@otdel-1.org>
Now most big problem of IPv6 is getting IPv6 address
assignment.
6to4 solve the problem. 6to4 addr is defined like below,
2002: 4byte v4 addr : 2byte SLA ID : 8byte interface ID
The most important point of the address format is that an IPv4 addr
is embeded in it. So any user who has IPv4 addr can get IPv6 address
block with 2byte subnet space. Also, the IPv4 addr is used for
semi-automatic IPv6 over IPv4 tunneling.
With 6to4, getting IPv6 addr become dramatically easy.
The attached patch enable 6to4 extension, and confirmed to work,
between "Richard Seaman, Jr." <dick@tar.com> and me.
Approved by: jkh
Reviewed by: itojun
ARP packets. This can incorrectly reject complete frames since the frame
could be stored in more than one mbuf.
The following patches fix the length comparisson, and add several
diagnostic log messages to the interrupt handler for out-of-the-norm ARP
packets. This should make ARP problems easier to detect, diagnose and
fix.
Submitted by: C. Stephen Gunn <csg@waterspout.com>
Approved by: jkh
Reviewed by: rwatson
Without this, kernel will panic at getsockopt() of IPSEC_POLICY.
Also make compilable libipsec/test-policy.c which tries getsockopt() of
IPSEC_POLICY.
Approved by: jkh
Submitted by: sakane@kame.net
KAME put INET6 related stuff into sys/netinet6 dir, but IPv6
standard API(RFC2553) require following files to be under sys/netinet.
netinet/ip6.h
netinet/icmp6.h
Now those header files just include each following files.
netinet6/ip6.h
netinet6/icmp6.h
Also KAME has netinet6/in6.h for easy INET6 common defs
sharing between different BSDs, but RFC2553 requires only
netinet/in.h should be included from userland.
So netinet/in.h also includes netinet6/in6.h inside.
To keep apps portability, apps should not directly include
above files from netinet6 dir.
Ideally, all contents of,
netinet6/ip6.h
netinet6/icmp6.h
netinet6/in6.h
should be moved into
netinet/ip6.h
netinet/icmp6.h
netinet/in.h
but to avoid big changes in this stage, add some hack, that
-Put some special macro define into those files under neitnet
-Let files under netinet6 cause error if it is included
from some apps, and, if the specifal macro define is not
defined.
(which should have been defined if files under netinet is
included)
-And let them print an error message which tells the
correct name of the include file to be included.
Also fix apps which includes invalid header files.
Approved by: jkh
Obtained from: KAME project
at the same time.
When rfc1323 and rfc1644 option are enabled by sysctl,
and tcp over IPv6 is tried, kernel panic happens by the
following check in tcp_output(), because now hdrlen is bigger
in such case than before.
/*#ifdef DIAGNOSTIC*/
if (max_linkhdr + hdrlen > MHLEN)
panic("tcphdr too big");
/*#endif*/
So change the above check to compare with MCLBYTES in #ifdef INET6 case.
Also, allocate a mbuf cluster for the header mbuf, in that case.
Bug reported at KAME environment.
Approved by: jkh
Reviewed by: sumikawa
Obtained from: KAME project
This is fix to usr.sbin/trpt and tcp_debug.[ch]
I think of putting this after 4.0 but,,,
-There was bug that when INET6 is defined,
IPv4 socket is not traced by trpt.
-I received request from a person who distribute a program
which use tcp_debug interface and print performance statistics,
that
-leave comptibility with old program as much as possible
-use same interface with other OSes
So, I talked with itojun, and synced API with netbsd IPv6 extension.
makeworld check, kernel build check(includes GENERIC) is done.
But if there happen to any problem, please let me know and
I soon backout this change.
o Drop all broadcast and multicast source addresses in tcp_input.
o Enable ICMP_BANDLIM in GENERIC.
o Change default to 200/s from 100/s. This will still stop the attack, but
is conservative enough to do this close to code freeze.
This is not the optimal patch for the problem, but is likely the least
intrusive patch that can be made for this.
Obtained from: Don Lewis and Matt Dillon.
Reviewed by: freebsd-security
for IPv4 communication.(IPv4 mapped IPv6 addr.)
Also removed IPv6 hoplimit initialization because it is alway done at
tcp_output.
Confirmed by: Bernd Walter <ticso@cicely5.cicely.de>
include this in all kernels. Declare some const *intrq_present
variables that can be checked by a module prior to using *intrq
to queue data.
Make the if_tun module capable of processing atm, ip, ip6, ipx,
natm and netatalk packets when TUNSIFHEAD is ioctl()d on.
Review not required by: freebsd-hackers
-opt_ipsec.h was missing on some tcp files (sorry for basic mistake)
-made buildable as above fix
-also added some missing IPv4 mapped IPv6 addr consideration into
ipsec4_getpolicybysock
This must be one of the reason why connections over IPsec hangs for
bigger packets.(which was reported on freebsd-current@freebsd.org)
But there still seems to be another bug and the problem is not yet fixed.
is very likely to become consensus as recent ietf/ipng mailing list
discussion. Also recent KAME repository and other KAME patched BSDs
also applied it.
s/__ss_family/ss_family/
s/__ss_len/ss_len/
Makeworld is confirmed, and no application should be affected by this change
yet.
now you can dynamically create rate-limited queues for different
flows using masks on dst/src IP, port and protocols.
Read the ipfw(8) manpage for details and examples.
Restructure the internals of the traffic shaper to use heaps,
so that it manages efficiently large number of queues.
Fix a bug which was present in the previous versions which could
cause, under certain unfrequent conditions, to send out very large
bursts of traffic.
All in all, this new code is much cleaner than the previous one and
should also perform better.
Work supported by Akamba Corp.
is an application space macro and the applications are supposed to be free
to use it as they please (but cannot). This is consistant with the other
BSD's who made this change quite some time ago. More commits to come.
desperation measure in low-memory situations), walk the tcpbs and
flush the reassembly queues.
This behaviour is currently controlled by the debug.do_tcpdrain sysctl
(defaults to on).
Submitted by: Bosko Milekic <bmilekic@dsuper.net>
Reviewed by: wollman
pr_input() routines prototype is also changed to support IPSEC and IPV6
chained protocol headers.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
to print out protocol specific pcb info.
A patch submitted by guido@gvr.org, and asmodai@wxs.nl also reported
the problem.
Thanks and sorry for your troubles.
Submitted by: guido@gvr.org
Reviewed by: shin
packet divert at kernel for IPv6/IPv4 translater daemon
This includes queue related patch submitted by jburkhol@home.com.
Submitted by: queue related patch from jburkhol@home.com
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
the old one: an unnecessary define (KLD_MODULE) has been deleted and
the initialisation of the module is done after domaininit was called
to be sure inet is running.
Some slight changed were made to ip_auth.c and ip_state.c in order
to assure including of sys/systm.h in case we make a kld
Make sure ip_fil does nmot include osreldate in kernel mode
Remove mlfk_ipl.c from here: no sources allowed in these directories!
- Implement 'ipfw tee' (finally)
- Divert packets by calling new function divert_packet() directly instead
of going through protosw[].
- Replace kludgey global variable 'ip_divert_port' with a function parameter
to divert_packet()
- Replace kludgey global variable 'frag_divert_port' with a function parameter
to ip_reass()
- style(9) fixes
Reviewed by: julian, green
This results in closer behavior to earlier versions, where the fixed
200ms timer actually resulted in a delay anywhere from 1..200ms, with
the average delay being 100ms.
Pointed out by: dg
for IPv6 yet)
With this patch, you can assigne IPv6 addr automatically, and can reply to
IPv6 ping.
Reviewed by: freebsd-arch, cvs-committers
Obtained from: KAME project
to be dangerous. It will better serve us as a port building a KLD,
ala SKIP.
The hooks are staying although it would be better to port and use
the NetBSD pfil interface rather than have custom hooks.
the link are equal to the default aliasing address. Do not zero them!
This will fix the problem with non-working links added with the source
and/or aliasing address equal to the default aliasing address, but the
default aliasing address is set later, after the link has been set up,
like both natd(8) and ppp(8) do (for objective reasons).
Reviewed by: Brian Somers <brian@FreeBSD.org>,
Eivind Eklund <eivind@FreeBSD.org>,
Charles Mott <cmott@srv.net>
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
`dst_port') work for outgoing packets.
- Make permanent links whose `alias_addr' matches the primary aliasing
address `aliasAddress' work for incoming packets.
- Typo fixes.
Reviewed by: brian, eivind
Make a sonewconn3() which takes an extra argument (proc) so new sockets created
with sonewconn() from a user's system call get the correct credentials, not
just the parent's credentials.
In the words of originator:
:If an incoming connection is initiated through natd and deny_incoming is
:not set, then a new alias_link structure is created to handle the link.
:If there is nothing listening for the incoming connection, then the kernel
:responds with a RST for the connection. However, this is not processed
:correctly in libalias/alias.c:TcpMonitor{In,Out} and
:libalias/alias_db.c:SetState{In,Out} as it thinks a connection
:has been established and therefore applies a timeout of 86400 seconds
:to the link.
:
:If many of these half-connections are initiated (during, for example, a
:port scan of the host), then many thousands of unnecessary links are
:created and the resident size of natd balloons to 20MB or more.
PR: 13639
Reviewed by: brian
- eliminate the fast/slow timeout lists for TCP and instead use a
callout entry for each timer.
- increase the TCP timer granularity to HZ
- implement "bad retransmit" recovery, as presented in
"On Estimating End-to-End Network Path Properties", by Allman and Paxson.
Submitted by: jlemon, wollmann
using syslog(3) (log(9)) for its various purposes! This long-awaited
change also includes such nice things as:
* macros expanding into _two_ comma-delimited arguments!
* snprintf!
* more snprintf!
* linting and criticism by more people than you can shake a stick at!
* a slightly more uniform message style than before!
and last but not least
* no less than 5 rewrites!
Reviewed by: committers
drop any segment arriving at a closed port.
tcp.blackhole=1 - only drop SYN without RST
tcp.blackhole=2 - drop everything without RST
tcp.blackhole=0 - always send RST - default behaviour
This confuses nmap -sF or -sX or -sN quite badly.
sysctl knobs.
With these knobs on, refused connection attempts are dropped
without sending a RST, or Port unreachable in the UDP case.
In the TCP case, sending of RST is inhibited iff the incoming
segment was a SYN.
Docs and rc.conf settings to follow.
- Sort xrefs
- FreeBSD.ORG -> FreeBSD.org
- Be consistent with section names as outlines in mdoc(7)
- Other misc mdoc cleanup.
PR: doc/13144
Submitted by: Alexy M. Zelkin <phantom@cris.net>
with a match probability to achieve non-deterministic behaviour of
the firewall. This can be extremely useful for testing purposes
such as simulating random packet drop without having to use dummynet
(which already does the same thing), and simulating multipath effects
and the associated out-of-order delivery (this time in conjunction
with dummynet).
The overhead on normal rules is just one comparison with 0.
Since it would have been trivial to implement this by just adding
a field to the ip_fw structure, I decided to do it in a
backward-compatible way (i.e. struct ip_fw is unchanged, and as a
consequence you don't need to recompile ipfw if you don't want to
use this feature), since this was also useful for -STABLE.
When, at some point, someone decides to change struct ip_fw, please
add a length field and a version number at the beginning, so userland
apps can keep working even if they are out of sync with the kernel.
respectively logging and dropping ICMP REDIRECT packets.
Note that there is no rate limiting on the log messages, so log_redirect
should be used with caution (preferrably only for debugging purposes).
_or_ you may specify "log logamount number" to set logging specifically
the rule.
In addition, "ipfw resetlog" has been added, which will reset the
logging counters on any/all rule(s). ipfw resetlog does not affect
the packet/byte counters (as ipfw reset does), and is the only "set"
command that can be run at securelevel >= 3.
This should address complaints about not being able to set logging
amounts, not being able to restart logging at a high securelevel,
and not being able to just reset logging without resetting all of the
counters in a rule.
would make a difference. However, my previous diff _did_ change the
behavior in some way (not necessarily break it), so I'm fixing it.
Found by: bde
Submitted by: bde
exit on errors.
If we don't, in_pcbrehash() is called without a preceeding
in_pcbinshash(), causing a crash.
There are apparently several conditions that could cause the crash;
PR misc/12256 is only one of these.
PR: misc/12256
This is the change to struct sockets that gets rid of so_uid and replaces
it with a much more useful struct pcred *so_cred. This is here to be able
to do socket-level credential checks (i.e. IPFW uid/gid support, to be added
to HEAD soon). Along with this comes an update to pidentd which greatly
simplifies the code necessary to get a uid from a socket. Soon to come:
a sysctl() interface to finding individual sockets' credentials.
to either enqueue or free their mbuf chains, but tcp_usr_send() was
dropping them on the floor if the tcpcb/inpcb has been torn down in the
middle of a send/write attempt. This has been responsible for a wide
variety of mbuf leak patterns, ranging from slow gradual leakage to rather
rapid exhaustion. This has been a problem since before 2.2 was branched
and appears to have been fixed in rev 1.16 and lost in 1.23/1.28.
Thanks to Jayanth Vijayaraghavan <jayanth@yahoo-inc.com> for checking
(extensively) into this on a live production 2.2.x system and that it
was the actual cause of the leak and looks like it fixes it. The machine
in question was loosing (from memory) about 150 mbufs per hour under
load and a change similar to this stopped it. (Don't blame Jayanth
for this patch though)
An alternative approach to this would be to recheck SS_CANTSENDMORE etc
inside the splnet() right before calling pru_send() after all the potential
sleeps, interrupts and delays have happened. However, this would mean
exposing knowledge of the tcp stack's reset handling and removal of the
pcb to the generic code. There are other things that call pru_send()
directly though.
Problem originally noted by: John Plevyak <jplevyak@inktomi.com>
The cdevsw_add() function now finds the major number(s) in the
struct cdevsw passed to it. cdevsw_add_generic() is no longer
needed, cdevsw_add() does the same thing.
cdevsw_add() will print an message if the d_maj field looks bogus.
Remove nblkdev and nchrdev variables. Most places they were used
bogusly. Instead check a dev_t for validity by seeing if devsw()
or bdevsw() returns NULL.
Move bdevsw() and devsw() functions to kern/kern_conf.c
Bump __FreeBSD_version to 400006
This commit removes:
72 bogus makedev() calls
26 bogus SYSINIT functions
if_xe.c bogusly accessed cdevsw[], author/maintainer please fix.
I4b and vinum not changed. Patches emailed to authors. LINT
probably broken until they catch up.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
