- Set UMA_ZONE_NOFREE so that the per-turnstile spin locks are type stable
to avoid a race where one thread might dereference a lock in a free'd
turnstile that was previously used by another thread.
Theorized by: tegge (2)
MFC after: 1 week
for all three contexts and configure the dt512_1 to hold 4MB pages for
them (e.g. for direct mappings).
This might allow for additional optimization by using the faulting
page sizes provided by AA_DMMU_TAG_ACCESS_EXT for bypassing the page
size walker for the dt512 in the superpage support code.
Submitted by: nwhitehorn (initial patch)
to synchronization needed after stores to internal ASIs in order
to make side-effects visible. This mainly requires the MEMBAR #Sync
after such stores to be replaced with a FLUSH. We use KERNBASE as
the address to FLUSH as it is guaranteed to not trap. Actually,
the USII synchronization rules also already require a FLUSH in
pretty much all of the cases changed.
We're also hitting an additional USIII synchronization rule which
requires stores to AA_IMMU_SFSR to be immediately followed by a DONE,
FLUSH or RETRY. Doing so triggers a RED state exception though so
leave the MEMBAR #Sync. Linux apparently also has gotten away with
doing the same for quite some time now, apart from the fact that
it's not clear to me why we need to clear the valid bit from the
SFSR in the first place.
Reviewed by: nwhitehorn
the ncr53c9x.c core where it actually belongs so future front-ends
don't need to add it.
o Use the correct OFW property when looking for the initiator ID of the
SBus device.
o Don't specify an alignment when creating the parent DMA tag for
SUNW,fas; their DMA engine doesn't require an alignment constraint
and it's no inherited by the child DMA tags anyway (which probably
is a bug though).
o Drop the superfluous sc_maxsync and use sc_minsync instead. The
former apparently was added due to a confusion with the maximum
frequency used in cam(4), which basically corresponds to the
inverse of minimum sync period.
o Merge ncr53c9x.c from NetBSD:
1.116: NCRDMA_SETUP() should be called before NCR_SET_COUNT() and
NCRCMD_DMA command in ncr53c9x_select().
1.125: free allocated resources on detach.
o Static'ize ncr53c9x_action(), ncr53c9x_init() and ncr53c9x_reset()
as these are not required outside of ncr53c9x.c.
o In ncr53c9x_attach() don't leak the device mutex in case attaching
fails.
o Register an asynchronous notification handler so in case cam(4)
reports a lost device we can cancel outstanding commands and
restore the default parameters for the target in question.
o For FAS366 correctly support 16-bit target IDs and let it know
that we use 32-bit transfers.
o Overhaul the negotiation of transfer settings. This includes
distinguishing between current and goal transfer settings of the
target so we can renegotiate their goal settings when necessary
and correcting the order in which tagged, wide and synchronous
transfers are negotiated.
o If we are requesting sense, force a renegotiation if we are
currently using anything different from asynchronous at 8 bit
as the target might have lost our transfer negotiations.
o In case of an XPT_RESET_BUS just directly call ncr53c9x_init()
instead of issuing a NCRCMD_RSTSCSI, which in turn will issue an
interrupt that is treated as an unexpected SCSI bus reset by
ncr53c9x_intr() and thus calls ncr53c9x_init(). Remove the now
no longer used ncr53c9x_scsi_reset().
o Correct an off-by-one error when setting cpi->max_lun.
o In replace printf(9) with device_printf(9) calls where appropriate
and in ncr53c9x_action() remove some unnecessarily verbose messages.
o In ncr53c9x_sched() use TAILQ_FOREACH() instead of reimplementing
it and consolidate two tagging-related target info checks into one.
o In ncr53c9x_done() set the CAM status to CAM_SCSI_STATUS_ERROR when
appropriate, respect CAM_DIS_AUTOSENSE and teach it to return SCSI
status information.
o In ncr53c9x_dequeue() ensure the tags are cleared.
o Use ulmin() instead of min() where appropriate.
o In ncr53c9x_msgout() consistently use the reset label.
o When we're interrupted during a data phase and the DMA engine is
still active, don't panic but reset the core and the DMA engine as
this should be sufficient. Also, the typical problem for triggering
this was the lack of renegotiation when requesting sense.
o Correctly handle DEVICE RESETs.
o Adapt the locking of esp(4) to MPSAFE cam(4). This includes moving
the calls of lsi64854_attach() to the bus front-ends so it can pass
the esp(4) mutex to bus_dma_tag_create(9).
o Change the LSI64854 driver to not create a DMA tag and map for the
Ethernet channel as le(4) will handle these on its own as well as
sync and unload the DMA maps for the SCSI and parallel port channel
after a DMA transfer.
o Cam(4)'ify some NetBSD-centric comments.
o Use bus_{read,write}_*(9) instead of bus_space_{read,write}_*(9)
and take advantage of rman_get_rid(9) in order to save some softc
members.
Reviewed by: scottl
MFC after: 1 month
it had been assigned to the last sleeping thread. That thread might have
started running on another CPU and have reused that sleep queue. Fix it
by just walking the thread queue using TAILQ_FOREACH_SAFE() rather than
a while loop.
PR: amd64/124200
Discovered by: tegge
Tested by: benjsc
MFC after: 1 week
but needs a lot more work. In particular, it has no flow control and has
a tendency to race when giving commands. It still uses Giant for the
tty and driver lock, but this is a keep-it-simple feature for now.
Some of the [temporary] proliferation of messages lines are way too long.
location in GDT where the segment descriptor from pcb_gs32sd is
copied, and the location is in GDT local to CPU.
Noted and reviewed by: peter
MFC after: 1 week
don't inline the locking primitives, and only grab those parts of mii
that we really need. Other space optimizations are too agressive for
the generic file (removing all of usb, and loading it as kernel
modules).
Payload Length) as set in tcpip_fillheaders().
ip6_output() will calculate it based of the length from the
mbuf packet header itself.
So initialize the value in tcpip_fillheaders() in correct
(network) byte order.
With the above change, to my reading, all places calling tcp_trace()
pass in the ip6 header via ipgen as serialized in the mbuf and with
ip6_plen in network byte order.
Thus convert the IPv6 payload length to host byte order before printing.
MFC after: 2 months
o It has been tested only on KB9202, KB9202A and KB9202B boards
o Better comments about hints
o option<space><tab>
o Add newer SX_NOINLINE option.
o Fix a few comments
calls the latter.
Merge tcp_mss_update() with code from tcp_mtudisc() basically
doing the same thing.
This gives us one central place where we calcuate and check mss values
to update t_maxopd (maximum mss + options length) instead of two slightly
different but almost equal implementations to maintain.
PR: kern/118455
Reviewed by: silby (back in March)
MFC after: 2 months
l_ucontext. To restore the registers content, trampoline needs to
dereference uc_mcontext instead of taking some undefined values from
l_ucontext.
Submitted by: Dmitry Chagin <dchagin@>
MFC after: 1 week
SYSCTL_PROCs and check that the default mss for neither v4 nor
v6 goes below the minimum MSS constant (216).
This prevents people from shooting themselves in the foot.
PR: kern/118455 (remotely related)
Reviewed by: silby (as part of a larger patch in March)
MFC after: 2 months
- Add a routine for looking up a device and checking if it is a valid geom
provider given a partial or full path to its device node.
Reviewed by: phk
Approved by: pjd (mentor)
somehow.
As a consequence we may now get an unexpected result(*).
Catch that error cases with a well defined panic giving appropriate
pointers to ease debugging.
(*) While the concensus was that the case should never happen unless
there was a bug, noone was definitively sure.
Discussed with: kmacy (about 8 months back)
Reviewed by: silby (as part of a larger patch in March)
MFC after: 2 months
This is different to the first one (as len gets updated between those
two) and would have caught various edge cases (read bugs) at a well
defined place I had been debugging the last months instead of
triggering (random) panics further down the call graph.
MFC after: 2 months
the default rule number but also the maximum rule number. User space
software such as ipfw and natd should be aware of its value. The
software that already includes ip_fw.h should use the defined value. All
other a expected to use sysctl (as discussed on net@).
MFC after: 5 days.
Discussed on: net@
