used by other places that expect to unwind the stack, e.g. dtrace and
stack(9).
As I have written most of this code I'm changing the license to the
standard FreeBSD license. I have received approval from the other
developers who have changed any of the affected code.
Approved by: ian, imp, rpaulo, eadler (all license change)
Switch the cache line size during invalidations/flushes
to be read from CP15 cache type register.
Submitted by: Wojciech Macek <wma@semihalf.com>
Reviewed by: ian, imp
Obtained from: Semihalf
With this commit any of the GPIO pins can now be programmed to act as an
interrupt source for GPIO devices (i.e. limited to devices directly
attached to gpiobus - at least for now).
Differential Revision: https://reviews.freebsd.org/D1000
The DISP DPLL clock is slower and was making the PRU programs slower
on FreeBSD than on Linux.
Submitted by: Manuel Stuehn <freebsdnewbie at freenet.de>
MFC after: 1 week
const. On x86, even after the machine context is supposedly read into
the struct ucontext, lazy FPU state save code might only mark the FPU
data as hardware-owned. Later, set_fpcontext() needs to fetch the
state from hardware, modifying the *mcp.
The set_mcontext(9) is called from sigreturn(2) and setcontext(2)
implementations and old create_thread(2) interface, which throw the
*mcp out after the set_mcontext() call.
Reported by: dim
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
Allocate all four, we will use them soon.
Simplificate the allocation of memory and interrupt resources with a single
bus_alloc_resources() call instead of doing them separately.
Destroy the mutex in case of errors.
With this change, it is now possible to verify the pin function and level
of reserved pins (but not set them).
The use of reserved pins on Raspberry pi can lead to short circuits and
real damage to the SoC.
While here, remove duplicated code, make use of OF_getencprop_alloc()
instead of using fixed sized variables and reduce the dmesg spam by
printing reserved pin ranges (when possible) instead of printing each pin
in the range.
string.
With this change it is not necessary redeclare the driver relations with
gpiobus and gpioc.
This also prevents redundant declarations when gpiobusvar.h is included
(which is going to happen soon).
Minimum LCDC is 2 so clock freq shouild be 2*max_pixel_clock. Maximum pixel
clock for HDMI is 148500 (1920x1080). But AM335x can not run in this mode
due to bandwidth and clock limitations
lock around the mapping and uiomove(). Before r277643, it was
partially protected by Giant (but potential sleeping in fault from
uiomove() would still allow other thread to reuse the mapping).
Noted by: ian
Reviewed by: alc, ian
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
1 second is not enugh for TDA19988 HDMI framer (e.g. on Beaglebone Black)
- Add per-device i2c_timout sysctl (dev.iichb.X.i2c_timeout) to control
I2C bus timeout manually
- Pass softc instead of device_t to all sysctl handlers
o Digital Audio Multiplexer (AUDMUX)
o Smart Direct Memory Access Controller (SDMA)
o Synchronous Serial Interface (SSI)
Disable by default as it depends on SDMA firmware.
Sponsored by: Machdep, Inc.
for i386, and from the code inspection, nothing in the
arm/mips/sparc64 implementations depends on it.
Discussed with: imp, nwhitehorn
Sponsored by: The FreeBSD Foundation
MFC after: 3 weeks
the data the inline functions access together at the start of the bus_space
struct. The start-of part isn't so important, it's the grouping-together
that's the point: now all the most-accessed data should be in one cache line.
Suggested by: cognet
