controller, but make it optional.
After a problem report from Andrew Boyer, it looks like the LSI
chip may have issues (the watchdog timer fired) if too many aborts
are sent down to the chip at the same time. We know that task
management commands are serialized, and although the manual doesn't
say it, it may be a good idea to just send one at a time.
But, since I'm not certain that this is necessary, add a tunable
and sysctl variable (hw.mps.%d.allow_multiple_tm_cmds) to control
the driver's behavior.
mps.c: Add support for the sysctl and tunable, and add a
comment about the possible return values to
mps_map_command().
mps_sas.c: Run all task management commands through two new
routines, mpssas_issue_tm_request() and
mpssas_complete_tm_request().
This allows us to optionally serialize task
management commands. Also, change things so that
the response to a task management command always
comes back through the callback. (Before it could
come via the callback or the return value.)
mpsvar.h: Add softc variables for the list of active task
management commands, the number of active commands,
and whether we should allow multiple active task
management commands. Add an active command flag.
mps.4: Describe the new sysctl/loader tunable variable.
Sponsored by: Spectra Logic Corporation
A new function prep_devname() sanitizes a device name by removing
leading and redundant sequential slashes. The function returns an error
for names which already exist or are considered invalid.
A new flag MAKEDEV_CHECKNAME for make_dev_p(9) and make_dev_credf(9)
indicates that the caller is prepared to handle an error related to the
device name. An invalid name triggers a panic if the flag is not
specified.
Document the MAKEDEV_CHECKNAME flag in the make_dev(9) manual page.
Idea from: kib
Reviewed by: kib
Wrap lines for SiS and Promise entries to 80 columns.
This doesn't change appearance in page rendered with troff or man.cgi.
PR: docs/146195
Approved by: kib (mentor)
MFC after: 1 week
bcm4306 cards are ambiguous. BCM4306 rev 2 requires bwi. BCM4306 rev
3 will work with either. Since we can't easily determine which is
which, just remove them.
The $ip6addrctl_policy is a variable to choose a pre-defined address
selection policy set by ip6addrctl(8).
The keyword "ipv4_prefer" sets IPv4-preferred one described in Section 10.3,
the keyword "ipv6_prefer" sets IPv6-preferred one in Section 2.1 in RFC 3484,
respectively. When "AUTO" is specified, it attempts to read
/etc/ip6addrctl.conf first. If it is found, it reads and installs it as
a policy table. If not, either of the two pre-defined policy tables is
chosen automatically according to $ipv6_activate_all_interfaces.
When $ipv6_activate_all_interfaces=NO, interfaces which have no corresponding
$ifconfig_IF_ipv6 is marked as IFDISABLED for security reason.
The default values are ip6addrctl_policy=AUTO and
ipv6_activate_all_interfaces=NO.
Discussed with: ume and bz
code associated with overflow or with the drain function. While this
function is not expected to be used often, it produces more information
in the form of an errno that sbuf_overflowed() did.
called when the sbuf internal buffer is filled. For kernel sbufs with a
drain, the internal buffer will never be expanded. For userland sbufs
with a drain, the internal buffer may still be expanded by
sbuf_[v]printf(3).
Sbufs now have three basic uses:
1) static string manipulation. Overflow is marked.
2) dynamic string manipulation. Overflow triggers string growth.
3) drained string manipulation. Overflow triggers draining.
In all cases the manipulation is 'safe' in that overflow is detected and
managed.
Reviewed by: phk (the previous version)
a solution is using PIO mode. As fas as I know all open source based
broadcom drivers for specially LP PHY has this issue because it's
a reverse engineered driver from wl(4).
Pointed by: Warren Block <wblock at wonkity.com>
