seconds of idling, DRITY flags are removed.
- If mirror is in idle state or is not open for writing, sleep without
timeout when waiting for I/O requests.
- Don't use atomic operations, for now sysctls are protected by Giant.
- Update debugs.
- Fix for good (I hope) force-stopping mirrors and some filure cases
(e.g. the last good component dies when synchronization is in progress).
Don't use ->nstart/->nend consumer's fields, as this could be racy,
because those fields are used in g_down/g_up, use ->index consumer's
field instead for tracking number of not finished requests.
Reported by: marcel
- After 5 seconds of idle time (this should be configurable) mark all
dirty providers as clean, so when mirror is not used in 5 seconds
and there will be power failure, no synchronization on boot is needed.
Idea from: sorry, I can't find who suggested this
- When there are no ACTIVE components and no NEW components destroy whole
mirror, not only provider.
- Fix one debug to show information about I/O request, before we change
its command.
buf->b-dev.
Put a bio between the buf passed to dev_strategy() and the device driver
strategy routine in order to not clobber fields in the buf.
Assert copyright on vfs_bio.c and update copyright message to canonical
text. There is no legal difference between John Dysons two-clause
abbreviated BSD license and the canonical text.
This flag gets set whenever the thread posts an event on the GEOM
event queue, and if the flag is set when the thread is prepared
to return to userland from the kernel, g_waitidle() will be called
to make sure that the posted events have completed.
This can replace an insufficient number of g_waitidle() calls in
various other places, and has the advantage of being failsafe: Any
system call which does a VOP_OPEN()/VOP_CLOSE will now correctly
wait for any geom events it posted as part of spoils or tastes.
Assert that topology and Giant is not held in g_waitidle().
in the g_up and g_down threads. Each time a bio is propelled up and
down the stack, an event is generating showing the provider, offset,
and length, as well as thread wakeup and work status information.
providers for tasting. Before this hack, race below is possible:
SI_SUB_RAID (no not-fully-configured geoms, so don't block)
GEOM tasting (now geoms are created)
SI_SUB_MOUNT_ROOT (if root file system is placed on a mirror, it is
possible that this mirror is not fully configured yet)
There is a lot of work to do to avoid such hacks and I need a working
solution before 5.3, sorry.
Reported by: John Hay <jhay@icomtek.csir.co.za>
We have to use our own destroy_geom method, because default one, which
is a part of geom_slice is broken.
MT5 candidate.
PR: kern/72467
Submitted by: Vladimir Novoseltsev
by the time that kldload(8) returns. Satisfy that by making the GEOM
module load event -- only when the kernel is !cold -- wait until the
GEOM module init function has finished instead of returning immediately.
This is the other half of fixing md(8) (actually, "mfs" in fstab(5))
that is similar to r1.128 of src/sys/dev/md/md.c. This bug would be
why RAM disks would often fail on boot and the first call to mdconfig(8)
would probably fail.
pjd has ideas for not requiring kldload(8) to work synchronously for
control devices that could make this obsolete.
Silence on: -arch
This also adds support for bigger disks on the controller I have access to,
and maybe others if I understood the adhoc methods used on those.
Those with more PC98 bigdrive controllers it is hereby invited to add/fix
support for those in geom_pc98.c and not using #ifdef PC98 all over the place.
but it is possible:
1. Read data from good component for synchronization.
2. Write data to the same area.
3. Write synchronization data, which are now stale.
Found by: tegge (for gmirror)
but it is possible:
1. Read data from good component for synchronization.
2. Write data to the same area.
3. Write synchronization data, which are now stale.
Found by: tegge
Actually, it can even cause some problems, because GEOM requires sectorsize
to be more than 0 on first access, not on provider creation, so we can skip
valid providers by doing this check here.
Reported by: Divacky Roman <xdivac02@stud.fit.vutbr.cz>
Sven Willenberger <sven@dmv.com>
Analogous to the drive level, give each volume and plex a worker thread
that picks up and processes incoming and completed BIOs.
This should fix the data corruption issues that have come up a few
weeks ago and improve performance, especially of RAID5 plexes.
The volume level needs a little work, though.
sectorsize in order to avoid a lot of checks around various divisions etc.
Enforce the sectorsize being > 0 with a KASSERT on successful open.
Fix scsi_cd.c to return 2k sectors when no media inserted.
verification of regular data when device is in complete state.
On verification error, EIO error is returned for the bio and sysctl
kern.geom.raid3.stat.parity_mismatch is increased.
Suggested by: phk
as well, even if device is in complete state.
I observe 40% of speed-up with this option for random read operations,
but slowdown for sequential reads.
Basically, without this option reading from a RAID3 device built from 5
components (c0-c4) looks like this:
Request no. Used components
1 c0+c1+c2+c3
2 c0+c1+c2+c3
3 c0+c1+c2+c3
With the new feature:
Request no. Used components
1 c0+c1+c2+c3
2 (c1^c2^c3^c4)+c1+c2+c3
3 c0+(c0^c2^c3^c4)+c2+c3
4 c0+c1+(c0^c1^c3^c4)+c3
5 c0+c1+c2+(c0^c1^c2^c4)
6 c0+c1+c2+c3
[...]
drive is known to the configuration check also if it already has a geom.
Without this check several needless geoms are created and valid
configuration data was overwritten.
This change obsoletes the need for a separate geom to taste an
offered provider and the consumer doesn't need to be opened with the
exclusive bit set.
