New Stratus bnxt devices require support for short HWRM commands for VFs
to function. Enable their use, but only use them if it's both supported
and required... prefer the long HWRM commands when possible.
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D13269?id=36180
The firmware is always in little endian, use htole*() for all request fields
larger than one byte.
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Sponsored by: Broadcom Limited
Some bnxt devices do not correctly send frames smaller than
52 bytes (without CRC), so add a quirk that will pad frames to an
arbitrary size before passing off to the encap routine.
Reported by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D13269
Use our ifm_list of supported media types rather than nested switch
statements to find the current media type. Find a supported type that
matches the current speed.
Remove all workarounds while updating ifmr->ifm_active.
For BNXT_IFMEDIA_ADD, added Three more speeds IFM_10G_T, IFM_2500_T & IFM_2500_KX.
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D12896
1) Add new phy_types and speeds from the latest firmware header.
2) Introduced a macro to avoid code duplication and improve readability for
the invocation of ifmedia_add().
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D12423
Improved logging added in r323879 exposed an error during
attach. We need the irq, not the rid to work correctly. em uses
shared irqs, so it will use the same irq for TX as RX. bnxt does
not use shared irqs, or TX irqs at all, so there's no need to set
the TX irq affinity.
Reviewed by: sbruno
Approved by: sbruno (mentor)
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D12496
GPUs: radeonkms, i915kms
NICs: if_em, if_igb, if_bnxt
This metadata isn't used yet, but it will be handy to have later to
implement automatic module loading.
Reviewed by: imp, mmacy
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D12488
1) Choose correct Firmware options for HW LRO for best performance
2) Delete TBD and other comments which are not required.
3) Added sysctl interface to enable / disable / modify different factors
of HW LRO.
4) Disabled HW LRO by default to avoid issues with packet forwarding
This allows much better control over the LRO configuration via sysctls, and
uses much better defaults. Hardware LRO can now be enabled/disabled
independantly from the software LRO, and the tuning parameters are exposed.
manpage updates coming soon.
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D12223
- Use HWRM_FUNC_VF_CFG instead of HWRM_FUNC_CFG on VFs
- Fix NPAR/VF detection
- Clean up flag definitions
- Don't allow WoL on VFs
Although the bnxt driver doesn't support SR-IOV so can create VFs yet,
the PF could be running Linux or ESCi with a VF passed through to a
FreeBSD guest. This fixes the driver for that use case.
Submitted by: Siva Kallam <siva.kallam@@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D12410
This was really too big of a commit even if everything worked, but there
are multiple new issues introduced in the one huge commit, so it's not
worth keeping this until it's fixed.
I'll work on splitting this up into logical chunks and introduce them one
at a time over the next week or two.
Approved by: sbruno (mentor)
Sponsored by: Limelight Networks
by Matt Macy as well as other changes which he has accepted via pull
request to his github repo at https://github.com/mattmacy/networking/
This should bring -CURRENT and the github repo into close enough sync to
allow small feature branches rather than a large chain of interdependant
patches being developed out of tree. The reset of the synchronization
should be able to be completed on github by splitting the remaining
changes that are not yet ready into short feature branches for later
review as smaller commits.
Here is a summary of changes included in this patch:
1) More checks when INVARIANTS are enabled for eariler problem
detection
2) Group Task Queue cleanups
- Fix use of duplicate shortdesc for gtaskqueue malloc type.
Some interfaces such as memguard(9) use the short description to
identify malloc types, so duplicates should be avoided.
3) Allow gtaskqueues to use ithreads in addition to taskqueues
- In some cases, this can improve performance
4) Better logging when taskqgroup_attach*() fails to set interrupt
affinity.
5) Do not start gtaskqueues until they're needed
6) Have mp_ring enqueue function enter the ABDICATED rather than BUSY
state. This moves the TX to the gtaskq and allows processing to
continue faster as well as make TX batching more likely.
7) Add an ift_txd_errata function to struct if_txrx. This allows
drivers to inspect/modify mbufs before transmission.
8) Add a new IFLIB_NEED_ZERO_CSUM for drivers to indicate they need
checksums zeroed for checksum offload to work. This avoids modifying
packet data in the TX path when possible.
9) Use ithreads for iflib I/O instead of taskqueues
10) Clean up ioctl and support async ioctl functions
11) Prefetch two cachlines from each mbuf instead of one up to 128B. We
often need to parse packet header info beyond 64B.
12) Fix potential memory corruption due to fence post error in
bit_nclear() usage.
13) Improved hang detection and handling
14) If the packet is smaller than MTU, disable the TSO flags.
This avoids extra packet parsing when not needed.
15) Move TCP header parsing inside the IS_TSO?() test.
This avoids extra packet parsing when not needed.
16) Pass chains of mbufs that are not consumed by lro to if_input()
rather call if_input() for each mbuf.
17) Re-arrange packet header loads to get as much work as possible done
before a cache stall.
18) Lock the context when calling IFDI_ATTACH_PRE()/IFDI_ATTACH_POST()/
IFDI_DETACH();
19) Attempt to distribute RX/TX tasks across cores more sensibly,
especially when RX and TX share an interrupt. RX will attempt to
take the first threads on a core, and TX will attempt to take
successive threads.
20) Allow iflib_softirq_alloc_generic() to request affinity to the same
cpus an interrupt has affinity with. This allows TX queues to
ensure they are serviced by the socket the device is on.
21) Add new iflib sysctls to net.iflib:
- timer_int - interval at which to run per-queue timers in ticks
- force_busdma
22) Add new per-device iflib sysctls to dev.X.Y.iflib
- rx_budget allows tuning the batch size on the RX path
- watchdog_events Count of watchdog events seen since load
23) Fix error where netmap_rxq_init() could get called before
IFDI_INIT()
24) e1000: Fixed version of r323008: post-cold sleep instead of DELAY
when waiting for firmware
- After interrupts are enabled, convert all waits to sleeps
- Eliminates e1000 software/firmware synchronization busy waits after
startup
25) e1000: Remove special case for budget=1 in em_txrx.c
- Premature optimization which may actually be incorrect with
multi-segment packets
26) e1000: Split out TX interrupt rather than share an interrupt for
RX and TX.
- Allows better performance by keeping RX and TX paths separate
27) e1000: Separate igb from em code where suitable
Much easier to understand separate functions and "if (is_igb)" than
previous tests like "if (reg_icr & (E1000_ICR_RXSEQ | E1000_ICR_LSC))"
#blamebruno
Reviewed by: sbruno
Approved by: sbruno (mentor)
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D12235
This provides port stats (updated once per second) in
dev.bnxt.X.port_stats for PFs. VFs do not have access to the port stats.
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D11914
hsi_struct_def.h file contains all firmware (HWRM) data struct's, updated
that with the latest one which was released on 30'th Aug.
After this upgrade, HWRM version will be 1.8.1.5 (earlier it was 1.4.0).
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D12203
1) Based on the suggestion from firmware team, derive
scctx->isc_ntxqsets_max & scctx->isc_nrxqsets_max based on FUNC_QCFG
(instead of FUNC_QCAPS).
2) Bump-up driver version to "1.0.0.2".
Submitted by: Bhargava Chenna Marreddy <bhargava.marreddy@broadcom.com>
Reviewed by: shurd, sbruno
Approved by: sbruno (mentor)
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D12128
were redundant and not being used to set anything up.
Submitted by: Matt Macy <mmacy@mattmacy.io>
Reported by: Jeb Cramer <cramerj@intel.com>
Sponsored by: Limelight Networks
iflib - reset fl-ifl_fragidx to 0 on iflib_fl_bufs_free(). This caused the
panic in em/igb when adding it to a bridge device.
iflib - Handle out of order packet delivery from hardware in support of LRO
Out of order updates to rxd's is fixed in r315217. However, it is not
completely fixed. While refilling the buffers, iflib is not considering
the out of order descriptors. Hence, it is refilling sequentially.
"idx" variable in _iflib_fl_refill routine is incremented sequentially.
By doing refilling sequentially, it will override the SGEs that
are *IN USE* by other connections. Fix is to maintain a bitmap of
rx descriptors and differentiate the used one with unused one and
refill only at the unused indices. This patch also fixes a
few bugs in bnxt, related to the same feature.
Submitted by: bhargava.marreddy@broadcom.com
Reviewed by: venkatkumar.duvvuru@broadcom.com shurd
Differential Revision: https://reviews.freebsd.org/D10681
--Remove special-case handling of sparc64 bus_dmamap* functions.
Replace with a more generic mechanism that allows MD busdma
implementations to generate inline mapping functions by
defining WANT_INLINE_DMAMAP in <machine/bus_dma.h>. This
is currently useful for sparc64, x86, and arm64, which all
implement non-load dmamap operations as simple wrappers
around map objects which may be bus- or device-specific.
--Remove NULL-checked bus_dmamap macros. Implement the
equivalent NULL checks in the inlined x86 implementation.
For non-x86 platforms, these checks are a minor pessimization
as those platforms do not currently allow NULL maps. NULL
maps were originally allowed on arm64, which appears to have
been the motivation behind adding arm[64]-specific barriers
to bus_dma.h, but that support was removed in r299463.
--Simplify the internal interface used by the bus_dmamap_load*
variants and move it to bus_dma_internal.h
--Fix some drivers that directly include sys/bus_dma.h
despite the recommendations of bus_dma(9)
Reviewed by: kib (previous revision), marius
Differential Revision: https://reviews.freebsd.org/D10729
This generates startup LORs and panics when adding elements to bridge
devices. I will document further in https://reviews.freebsd.org/D10681
PR: 220073
Submitted by: dchagin
Reported by: db
iflib - Handle out of order packet delivery from hardware in support of LRO
Out of order updates to rxd's is fixed in r315217. However, it is not
completely fixed. While refilling the buffers, iflib is not considering
the out of order descriptors. Hence, it is refilling sequentially.
"idx" variable in _iflib_fl_refill routine is incremented sequentially.
By doing refilling sequentially, it will override the SGEs that
are *IN USE* by other connections. Fix is to maintain a bitmap of
rx descriptors and differentiate the used one with unused one and
refill only at the unused indices. This patch also fixes a
few bugs in bnxt, related to the same feature.
Submitted by: bhargava.marreddy@broadcom.com
Reviewed by: shurd@
Differential Revision: https://reviews.freebsd.org/D10681
- unconditionally enable BUS_DMA on non-x86 architectures
- speed up rxd zeroing via customized function
- support out of order updates to rxd's
- add prefetching to hardware descriptor rings
- only prefetch on 10G or faster hardware
- add seperate tx queue intr function
- preliminary rework of NETMAP interfaces, WIP
Submitted by: Matt Macy <mmacy@nextbsd.org>
Sponsored by: Limelight Networks
RSS hash type will be used to identify the CPU on to which, a receive packet
will be queued. This patch extracts the "RSS hash type" from the receive
completion and sends it to the stack.
Submitted by: Venkatkumar Duvvuru <venkatkumar.duvvuru@broadcom.com>
Reviewed by: shurd
Approved by: sbruno
MFC after: 1 week
Sponsored by: Broadcom Limited
Differential Revision: https://reviews.freebsd.org/D9685
- iflib - add checksum in place support (mmacy)
- iflib - initialize IP for TSO (going to be needed for e1000) (mmacy)
- iflib - move isc_txrx from shared context to softc context (mmacy)
- iflib - Normalize checks in TXQ drainage. (shurd)
- iflib - Fix queue capping checks (mmacy)
- iflib - Fix invalid assert, em can need 2 sentinels (mmacy)
- iflib - let the driver determine what capabilities are set and what
tx csum flags are used (mmacy)
- add INVARIANTS debugging hooks to gtaskqueue enqueue (mmacy)
- update bnxt(4) to support the changes to iflib (shurd)
Some other various, sundry updates. Slightly more verbose changelog:
Submitted by: mmacy@nextbsd.org
Reviewed by: shurd
mFC after:
Sponsored by: LimeLight Networks and Dell EMC Isilon
Minimal impact, would allow selection of LR media when KR is connected.
Reported by: Coverity
Approved by: davidch
MFC after: 7 days
Sponsored by: Broadcom Limited
Because link state change events aren't enabled until the end of init(),
the initial link up event could be missed. Check the current media status
immediately after enabling the default completion ring interrupt.
Approved by: sbruno
MFC after: 12 days
Sponsored by: Broadcom Limited
