CLAT is customer-side translator that algorithmically translates 1:1
private IPv4 addresses to global IPv6 addresses, and vice versa.
It is implemented as part of ipfw_nat64 kernel module. When module
is loaded or compiled into the kernel, it registers "nat64clat" external
action. External action named instance can be created using `create`
command and then used in ipfw rules. The create command accepts two
IPv6 prefixes `plat_prefix` and `clat_prefix`. If plat_prefix is ommitted,
IPv6 NAT64 Well-Known prefix 64:ff9b::/96 will be used.
# ipfw nat64clat CLAT create clat_prefix SRC_PFX plat_prefix DST_PFX
# ipfw add nat64clat CLAT ip4 from IPv4_PFX to any out
# ipfw add nat64clat CLAT ip6 from DST_PFX to SRC_PFX in
Obtained from: Yandex LLC
Submitted by: Boris N. Lytochkin
MFC after: 1 month
Relnotes: yes
Sponsored by: Yandex LLC
Add second IPv6 prefix to generic config structure and rename another
fields to conform to RFC6877. Now it contains two prefixes and length:
PLAT is provider-side translator that translates N:1 global IPv6 addresses
to global IPv4 addresses. CLAT is customer-side translator (XLAT) that
algorithmically translates 1:1 IPv4 addresses to global IPv6 addresses.
Use PLAT prefix in stateless (nat64stl) and stateful (nat64lsn)
translators.
Modify nat64_extract_ip4() and nat64_embed_ip4() functions to accept
prefix length and use plat_plen to specify prefix length.
Retire net.inet.ip.fw.nat64_allow_private sysctl variable.
Add NAT64_ALLOW_PRIVATE flag and use "allow_private" config option to
configure this ability separately for each NAT64 instance.
Obtained from: Yandex LLC
MFC after: 1 month
Sponsored by: Yandex LLC
The -l flag sends only the READ CAPACITY (16) sevice action. Normally
we send the READ CAPACITY (10) command, and only send RC16 when the
capacity is larger than 2TB (since that's the max RC10 can
report). However, some badly programmed drives report different
numbers for RC10 and RC16. This can be hard to diagnose, but generally
there's a "Logical block address out of range" error when RC16 reports
a larger number than RC10 and the RC10 number is the correct one. By
comparing the output of readcap with and without the -l argmuent, one
can determine if there's a mismatch and if the DA_Q_NO_RC16 quirk is
needed.
Reviewed by: ken@
Differential Revision: https://reviews.freebsd.org/D19536
All changes are hidden behind the EXPERIMENTAL option and are not compiled
in by default.
Add ND6_IFF_IPV6_ONLY_MANUAL to be able to set the interface into no-IPv4-mode
manually without router advertisement options. This will allow developers to
test software for the appropriate behaviour even on dual-stack networks or
IPv6-Only networks without the option being set in RA messages.
Update ifconfig to allow setting and displaying the flag.
Update the checks for the filters to check for either the automatic or the manual
flag to be set. Add REVARP to the list of filtered IPv4-related protocols and add
an input filter similar to the output filter.
Add a check, when receiving the IPv6-Only RA flag to see if the receiving
interface has any IPv4 configured. If it does, ignore the IPv6-Only flag.
Add a per-VNET global sysctl, which is on by default, to not process the automatic
RA IPv6-Only flag. This way an administrator (if this is compiled in) has control
over the behaviour in case the node still relies on IPv4.
The change removes SIOC[GS]IEEE80211 handling from ifconfig(8)
if WITHOUT_WIRELESS_SUPPORT=yes is set in src.conf(5).
Reviewed by: bz
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19289
inodes that reference directories. While here tighten the check for
comparing the last logical block with the end of the file.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: Netflix
filesystem block size. When a size is specified with the -S flag
to tunefs(8), round it up to the filesystem block size.
Reported by: Peter Holm
Tested by: Peter Holm
Sponsored by: Netflix
Eliminate trailing whitespace on inet, inet6, and groups lines. I think the
"list txpower" command will still show some, but I'm not able to test that.
PR: 153731
Reported-by: Nikolay Denev <ndenev@gmail.com>
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D19004
shorter than its size resulting in a hole as its final block (which
is a violation of the invarients of the UFS filesystem).
Soft updates will always ensure that the file size is correct when
writing inodes to disk for files that contain only direct block
pointers. However soft updates does not roll back sizes for files
with indirect blocks that it has set to unallocated because their
contents have not yet been written to disk. Hence, the file can
appear to have a hole at its end because the block pointer has been
rolled back to zero when its inode was written to disk. Thus,
fsck_ffs calculates the last allocated block in the file. For files
that extend into indirect blocks, fsck_ffs checks for a size past
the last allocated block of the file and if that is found, shortens
the file to reference the last allocated block thus avoiding having
it reference a hole at its end.
Submitted by: Chuck Silvers <chs@netflix.com>
Tested by: Chuck Silvers <chs@netflix.com>
MFC after: 1 week
Sponsored by: Netflix
A big security advantage of Wayland is not allowing applications to read
input devices all the time. Having /dev/input/* accessible to the user
account subverts this advantage.
libudev-devd was opening the evdev devices to detect their types (mouse,
keyboard, touchpad, etc). This don't work if /dev/input/* is inaccessible.
With the kernel exposing this information as sysctls (kern.evdev.input.*),
we can work w/o /dev/input/* access, preserving the Wayland security model.
Submitted by: Greg V <greg@unrelenting.technology>
Reviewed by: wulf, imp
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18694
MTU if we've set it once and there were no changes on the DHCP server
side since the last refresh. This is consistent I believe with how dhclient
handles other settings like IP address, mask etc.
Approved by: cem, eugen
Differential Revision: https://reviews.freebsd.org/D18546
Move from using a linker set to a constructor function that's
called. This simplifies the code and is slightly more obvious. We now
keep a list of page decoders rather than having an array we managed
before. Commands will move to something similar in the future.
Reviewed by: jhb@
Differential Revision: https://reviews.freebsd.org/D19275
pass of fsck_ffs. Some changes, such as check-hash corrections were
being lost.
Reported by: Michael Tuexen (tuexen@)
Tested by: Michael Tuexen (tuexen@)
MFC after: 3 days
Mentioned in mdconfig(8), malloc-backed md(4) can be unstable unless
required memory is allocated up front with -o reserve. Furthermore, panics
have been observed with md used in fstab on 12.0-RELEASE. Choose the stable
route and pass -o reserve.
Submitted by: Paul Vixie
MFC after: 1 week
Set up zpools with a more unique name, stash the zpool name away in a file pointed
to by `$ZPOOL_NAME_FILE` (which is relative to a per-testcase generated temporary
directory), then remove the file based on `$ZPOOL_NAME_FILE` in the cleanup
routines.
This is a more concurrency-safe solution and will allow the testcases to be safely
executed in parallel.
Reviewed by: kevans, jtl
Approved by: jtl (mentor)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D19024
The logic added in r343287 to avoid false-positive
sum-of-child-bandwidth check errors for HFSC queues has a bug in it
that causes the upperlimit service curve of an HFSC queue to be pulled
down to its parent's linkshare service curve if it happens to be above
it.
Upon further inspection/reflection, this generic
sum-of-child-bandwidths check does not need to be fixed for HFSC - it
needs to be skipped. For HFSC, the equivalent check is to ensure the
sum of child linkshare service curves are at or below the parent's
linkshare service curve, and this check is already being performed by
eval_pfqueue_hfsc().
This commit reverts the affected parts of r343287 and adds new logic
to skip the generic sum-of-child-bandwidths check for HFSC.
MFC after: 1 day
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D19124
This code allocated a correctly sized buffer, read past the end of the
source buffer, writing off the end of the target buffer, and then writing
a '\0' terminator past the end of the target buffer (in the wrong place).
It then leaked the buffer.
Switch to a statically sized buffer on the stack and update the source
pointer and
length before use so the correct things are copied.
Fix a logic error in the checks that the format of the line is as
expected and move on out of an assert.
Remove an unneeded close(). fclose() closes the descriptor.
Found with: CheriABI
Obtained from: CheriBSD
Reviewed by: kib, jhb, markj
Differential Revision: https://reviews.freebsd.org/D19122
We can't predict when destruction of origin is needed, and currently we have
a precedent for not prompting for things. Leave the decision up to the user
of bectl(8) if they want the origin snapshot to be destroyed or not.
Emits a warning when -o isn't used and an origin snapshot is left to be
cleaned up, for the time being. This is handy when one drops the -o flag but
really did want to clean up the origin.
A couple of -e ignore's have been sprinkled around the test suite for places
that we don't care that the origin's not been cleaned up. -o functionality
tests will be added in the future, but are omitted for now to reduce
conflicts with work in flight to fix bits of the tests.
Reported by: Shawn Webb
MFC after: 1 week
Setting the length of the request got lost in r343287, which means SIOCGIFGMEMB
gives us the required length, but does not copy the names of the group members.
As a result we don't get a correct list of group members, and 'set skip on
<ifgroup>' broke.
This produced all sorts of very unexpected results, because we would end up
applying 'set skip' to unexpected interfaces.
X-MFC-with: r343287
r343896 made it such that a non-zero exit status was passed through, but was
still wrong if the script exits on a signal. POSIX does not say what the
WEXITSTATUS macro returns in this case and in practice 0 is a common value.
Instead, translate the wait status into 8 bits the same way as the shell
calculates $?.
Reviewed by: kib, Nash Kaminski
MFC after: 1 week
This is also OpenBSD rev. 1.117, as pointed out by
Ryan Moeller <ryan@ixsystems.com>.
Submitted by: Nash Kaminski <nashkaminski@gmail.com>
MFC after: 1 week
Properly pass down is_all to table_show_list(). This restores the behavior
before r272840 so that only 'ipfw table all list' shows the headers.
MFC after: 2 weeks
Relnotes: yes
Use recent best practices for Copyright form at the top of
the license:
1. Remove all the All Rights Reserved clauses on our stuff. Where we
piggybacked others, use a separate line to make things clear.
2. Use "Netflix, Inc." everywhere.
3. Use a single line for the copyright for grep friendliness.
4. Use date ranges in all places for our stuff.
Approved by: Netflix Legal (who gave me the form), adrian@ (pmc files)
For 11n / 11ac we are still using non-11n rates for management and
multicast traffic by default; check 'MCS rate' bit to determine how
to print them correctly.
PR: 161035
MFC after: 1 week
The KPI have been reviewed and cleansed of features that were planned
back 20 years ago and never implemented. The pfil(9) internals have
been made opaque to protocols with only returned types and function
declarations exposed. The KPI is made more strict, but at the same time
more extensible, as kernel uses same command structures that userland
ioctl uses.
In nutshell [KA]PI is about declaring filtering points, declaring
filters and linking and unlinking them together.
New [KA]PI makes it possible to reconfigure pfil(9) configuration:
change order of hooks, rehook filter from one filtering point to a
different one, disconnect a hook on output leaving it on input only,
prepend/append a filter to existing list of filters.
Now it possible for a single packet filter to provide multiple rulesets
that may be linked to different points. Think of per-interface ACLs in
Cisco or Juniper. None of existing packet filters yet support that,
however limited usage is already possible, e.g. default ruleset can
be moved to single interface, as soon as interface would pride their
filtering points.
Another future feature is possiblity to create pfil heads, that provide
not an mbuf pointer but just a memory pointer with length. That would
allow filtering at very early stages of a packet lifecycle, e.g. when
packet has just been received by a NIC and no mbuf was yet allocated.
Differential Revision: https://reviews.freebsd.org/D18951
This is a wild guess as to why bectl tests failed once upon a time in CI,
given no apparent way to see a transcript of cleanup routines with Kyua. The
bectl tests construct a new, clean zpool for every test. The failure
indicated was because of a mount that was leftover from a previous test, but
the previous test had succeeded so it's not clear how the mount remained
leftover unless the `zpool get health ${pool}` had somehow failed.
MFC after: 1 week
When performing a non-status operation on a single interface, it is
not necessary for ifconfig to build a list of all addresses in the
system, sort them, then iterate through them looking for the entry for
the single interface of interest. Doing so becomes increasingly
expensive as the number of interfaces in the system grows (e.g., in a
system with 1000+ vlan(4) interfaces).
Reviewed by: ae, kp
MFC after: 1 week
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D18919
The kernel will reject very large tables to avoid resource exhaustion
attacks. Some users run into this limit with legitimate table
configurations.
The error message in this case was not very clear:
pf.conf:1: cannot define table nets: Invalid argument
pfctl: Syntax error in config file: pf rules not loaded
If a table definition fails we now check the request_maxcount sysctl,
and if we've tried to create more than that point the user at
net.pf.request_maxcount:
pf.conf:1: cannot define table nets: too many elements.
Consider increasing net.pf.request_maxcount.
pfctl: Syntax error in config file: pf rules not loaded
PR: 235076
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D18909
to make it consistent with newfs. Document the legality of '_'
in label names in both tunefs(8) and newfs(8).
PR: 235182
Submitted by: darius@dons.net.au
Reviewed by: Conrad Meyer
MFC after: 3 days
Sponsored by: Netflix
The number of syscalls made during parsing of any config that
defines tables is also reduced, and incorrect warnings that HFSC
parent queue bandwidths were smaller than the sum of their child
bandwidths have been fixed.
Reviewed by: kp
MFC after: 1 week
Sponsored by: RG Nets
Differential Revision: https://reviews.freebsd.org/D18759
Do not invoke 'wlan_up' function from devd(8) on interface
creation event (an example to create such event:
'ifconfig wlan0 create wlandev rtwn0');
they're typically produced during 'service netif (re)start'
and result in duplicate interface initialization.
From the user side if WPA option is used, this result in messages like:
- /etc/rc.d/wpa_supplicant: WARNING: failed to start wpa_supplicant
or
- wpa_supplicant already running? (pid=xxxx).
(for HOSTAP interfaces this race may result in startup failure).
As a side effect, wpa_supplicant(8) / hostapd(8) will not be
invoked when new wlan(4) interface is created manually and
corresponding configuration for it is present in rc.conf(5).
This change does not affect device attach / removal events.
MFC after: 5 days
When we skip on a group the kernel will automatically skip on the member
interfaces. We still need to update our own cache though, or we risk
overruling the kernel afterwards.
This manifested as 'set skip' working initially, then not working when
the rules were reloaded.
PR: 229241
MFC after: 1 week
This set of changes is geared towards making bectl respect deep boot
environments when they exist and are mounted. The deep BE composition
functionality (`bectl add`) remains disabled for the time being. This set of
changes has no effect for the average user. but allows deep BE users to
upgrade properly with their current setup.
libbe(3): Open the target boot environment and get a zfs handle, then pass
that with the target mountpoint to be_mount_iter; If the BE_MNT_DEEP flag is
set call zfs_iter_filesystems and mount the child datasets.
Similar logic is employed when unmounting the datasets, save for children
are unmounted first.
bectl(8): Change bectl_cmd_jail to pass the BE_MNT_DEEP flag when
calling be_mount as well as call be_unmount when cleaning up after the
jail has exited instead of umount(2) directly.
PR: 234795
Submitted by: Wes Maag <jwmaag_gmail.com> (test additions by kevans)
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D18796
Try to reword -prefixlen section to more clearly and accurately describe how
the -prefixlen modifier works.
While here, fix a word that igor considered a typo: aggregatable addresses is a
valid technical term per RFC-2374, however, it was superseded by the term
"aggregator" in RFC-3587.
MFC after: 1 week
Reviewed by: 0mp, crees
Approved by: emaste (mentor)
Differential Revision: https://reviews.freebsd.org/D10087
These programs parse ND6 Router Advertisement messages; rtsold(8) has
required an SA, SA-14:20.rtsold, for a bug in this code. Thus, they
are good candidates for sandboxing.
The approach taken is to run the main executable in capability mode
and use Casper services to provide functionality that cannot be
implemented within the sandbox. In particular, several custom services
were required.
- A Casper service is used to send Router Solicitation messages on a
raw ICMP6 socket. Initially I took the approach of creating a
socket for each interface upon startup, and connect(2)ing it to
the all-routers multicast group for the interface. This permits
the use of sendmsg(2) in capability mode, but only works if the
interface's link is up when rtsol(d) starts. So, instead, the
rtsold.sendmsg service is used to transmit RS messages on behalf
of the main process. One could alternately define a service
which simply creates and connects a socket for each destination
address, and returns the socket to the sandboxed process. However,
to implement rtsold's -m option we also need to read the ND6 default
router list, and this cannot be done in capability mode.
- rtsold may execute resolvconf(8) in response to RDNSS and DNSSL
options in received RA messages. A Casper service is used to
fork and exec resolvconf(8), and to reap the child process.
- A service is used to determine whether a given interface's
link-local address is useable (i.e., not duplicated or undergoing
DAD). This information is supplied by getifaddrs(3), which reads
a sysctl not available in capability mode. The SIOCGIFCONF socket
ioctl provides equivalent information and can be used in capability
mode, but I decided against it for now because of some limitations
of that interface.
In addition to these new services, cap_syslog(3) is used to send
messages to syslogd.
Reviewed by: oshogbo
Tested by: bz (previous versions)
MFC after: 2 months
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D17572
This follows the example of other Capsicumized programs in /sbin.
Reported by: Manfred Antar <manfredantar@gmail.com>
MFC with: r342699
Sponsored by: The FreeBSD Foundation
- Use cap_fileargs(3) to open dump devices after entering capability
mode, and use cap_syslog(3) to log messages.
- Use a relative directory fd to open output files.
- Use zdopen(3) to compress kernel dumps in capability mode.
Reviewed by: cem, oshogbo
MFC after: 2 months
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18458
By default, bectl is setting the jail 'name' parameter to the boot
environment name, which causes an error when the boot environment name is
not a valid jail name. With the attached fix, when no name is supplied, the
default jail name will be the jail id - this is is the same behavior as the
jail command.
Additionally, this commit addresses two other bugs that prevented unjailing
in scenarios where the jail name does not match the boot environment name:
1. In 'bectl_locate_jail', 'mountpoint' is used to resolve the boot
environment path, but really 'mounted' should be used. 'mountpoint' is the
path where the zfs dataset will be mounted. 'mounted' is the path where
the dataset is actually mounted.
2. in 'bectl_search_jail_paths', 'jail_getv' would fail after the first
call. Which is fine, if the boot environment you're unjailing is the next
one up. According to 'man jail_getv', it's expecting name and value
strings. 'jail_getv' is being passed an integer for the lastjid, so amend
that to use a string instead.
Test cases have been amended to reflect the bugs found.
PR: 233637
Submitted by: Rob <rob.fx907_gmail.com>
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D18607
The nvmecontrol code that did the devlist assumed that we had a
tightly-packed allocation of units. Since pci writing exists, this
isn't the case. Loop over the first 256 units, which is a reasonable
number of possible units.
Sponsored by: Netflix
implement not double-caching for reads from vnode-backed md devices.
Use VOP_ADVISE() similarly instead of !IO_DIRECT unsimilarly for writes.
Add a "cache" option to mdconfig to allow changing the default of not
caching.
This depends on a recent commit to fix VOP_ADVISE(). A previous version
had optimizations for sequential i/o's (merge the i/o's and only uncache
for discontiguous i/o's and for full blocks), but optimizations and
knowledge of block boundaries belong in VOP_ADVISE(). Read-ahead should
also be handled better, by supporting it in md and discarding it in
VOP_ADVISE().
POSIX_FADV_DONTNEED is ignored by zfs, but so is IO_DIRECT.
POSIX_FADV_DONTNEED works better than IO_DIRECT if it is not ignored,
since it only discards from the buffer cache immediately, while
IO_DIRECT also discards from the page cache immediately.
IO_DIRECT was not used for writes since it was claimed to be too slow,
but most of the slowness for writes is from doing them synchronously by
default. Non-synchronous writes still deadlock in many cases.
IO_DIRECT only has a special implementation for ffs reads with DIRECTIO
configured. Otherwise, if it is not ignored than it uses the buffer and
page caches normally except for discarding everything after each i/o,
and then it has much the same overheads as POSIX_FADV_DONTNEED. The
overheads for reading with ffs and DIRECTIO were similar in tests of md.
Reviewed by: kib
If requested to fix the inode check-hash it would confirm having done
it, but then fail to make the fix. The same code is used in fsdb which,
unlike fsck, would actually fix the inode check-hash.
The discrepancy occurred because fsck has two ways to fetch inodes.
The inode by number function ginode() and the streaming inode
function getnextinode() used during pass1. Fsdb uses the ginode()
function which correctly does the fix, while fsck first encounters
the bad inode check-hash in pass1 where it is using the getnextinode()
function that failed to make the correction. This patch corrects
the getnextinode() function so that fsck now correctly fixes inodes
with incorrect inode check-hashs.
Reported by: Gary Jennejohn <gljennjohn@gmail.com>
Sponsored by: Netflix
Also use caph_cache_catpages() to ensure that strerror() works when
run with kern.trap_enotcap=1.
Reviewed by: oshogbo
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D18514
check hash to the filesystem inodes. Access attempts to files
associated with an inode with an invalid check hash will fail with
EINVAL (Invalid argument). Access is reestablished after an fsck
is run to find and validate the inodes with invalid check-hashes.
This check avoids a class of filesystem panics related to corrupted
inodes. The hash is done using crc32c.
Note this check-hash is for the inode itself and not any of its
indirect blocks. Check-hash validation may be extended to also
cover indirect block pointers, but that will be a separate (and
more costly) feature.
Check hashes are added only to UFS2 and not to UFS1 as UFS1 is
primarily used in embedded systems with small memories and low-powered
processors which need as light-weight a filesystem as possible.
Reviewed by: kib
Tested by: Peter Holm
Sponsored by: Netflix
opcode will be printed. This should solve the problem, when protocol
name is not printed in `ipfw -N show`.
Reported by: Claudio Eichenberger <cei at yourshop.com>
MFC after: 1 week
Other vendors base their additional smart info pages on what Intel did
plus some other bits. So it's convenient to have this be global.
Sponsored by: Netflix
This was never documented, and isn't needed, so it's best removed to
avoid confusion.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18460
Make the pointers we pass into the commands const, also make the
linker set mirrors const.
Suggested by: cem@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18459
o Dynamically load all the .so files found in /libexec/nvmecontrol and
/usr/local/libexec/nvmecontrol.
o Link nvmecontrol -rdynamic so that its symbols are visible to the
libraries we load.
o Create concatinated linker sets that we dynamically expand.
o Add the linked-in top and logpage linker sets to the mirrors for them
and add those sets to the mirrors when we load a new .so.
o Add some macros to help hide the names of the linker sets.
o Update the man page.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18455
fold
superblock has a check-hash error, an error message noting the
superblock check-hash failure is printed and the mount fails. The
administrator then runs fsck to repair the filesystem and when
successful, the filesystem can once again be mounted.
This approach fails if the filesystem in question is a root filesystem
from which you are trying to boot. Here, the loader fails when trying
to access the filesystem to get the kernel to boot. So it is necessary
to allow the loader to ignore the superblock check-hash error and make
a best effort to read the kernel. The filesystem may be suffiently
corrupted that the read attempt fails, but there is no harm in trying
since the loader makes no attempt to write to the filesystem.
Once the kernel is loaded and starts to run, it attempts to mount its
root filesystem. Once again, failure means that it breaks to its prompt
to ask where to get its root filesystem. Unless you have an alternate
root filesystem, you are stuck.
Since the root filesystem is initially mounted read-only, it is
safe to make an attempt to mount the root filesystem with the failed
superblock check-hash. Thus, when asked to mount a root filesystem
with a failed superblock check-hash, the kernel prints a warning
message that the root filesystem superblock check-hash needs repair,
but notes that it is ignoring the error and proceeding. It does
mark the filesystem as needing an fsck which prevents it from being
enabled for writing until fsck has been run on it. The net effect
is that the reboot fails to single user, but at least at that point
the administrator has the tools at hand to fix the problem.
Reported by: Rick Macklem (rmacklem@)
Discussed with: Warner Losh (imp@)
Sponsored by: Netflix
This can be useful, when net.inet.ip.fw.dyn_keep_states is enabled, but
after rules reloading some state must be deleted. Added new flag '-D'
for such purpose.
Retire '-e' flag, since there can not be expired states in the meaning
that this flag historically had.
Also add "verbose" mode for listing of dynamic states, it can be enabled
with '-v' flag and adds additional information to states list. This can
be useful for debugging.
Obtained from: Yandex LLC
MFC after: 2 months
Sponsored by: Yandex LLC
This was a typo for wdc. Eliminate it since it was in error. People
should use either 'wdc' or 'hgst' for the vendor from now on. 'hgst'
works for all versions this functionality is present for.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Move the Intel specific log pages (including the one that samsung
implements) to intel.c. Add comment to the samsung vendor that it will
be going away soon.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Eliminage redundant spaces and nvmecontrol at start of all the usage
strings. Update the usage printing code to add them back when
presenting to the user. Allow multi-line usage messages and print
proper leading spaces for lines starting with a space.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
Provide a usage() function that takes a struct nvme_function pointer
and produces a usage mssage. Eliminate all now-redundant usage
functions. Propigate the new argument through the program as needed.
Use common routine to print usage.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
If the dispatched function doesn't exit, then we get can get a
spurious function not found message. They all do exit, but this is a
little cleaner.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D18403
