If we panic again shortly after boot (say, within 30 seconds), any core
dump we wrote out may be lost on reboot. In this situation, we really
want to keep that core file, as it may be the only way to have the issue
resolved. Call sync(8) after writing out the core file and running
crashinfo(8), in the hope that these will not be lost if we panic
again. sync(8) is only called in the case where there is a core dump
to be written out, so won't be called during normal boots.
Discovered by: Trying to debug an IPSEC panic
MFC after: 1 week
Newly-configured systems should use $cloned_interfaces.
- Call clone_{up,down}() and ifnet_rename() in rc.d/netif {start,stop}.
ifnet_rename() now accepts an interface name list as its argument.
- Add rc.d/netif clear. The "clear" subcommand is basically equivalent to
"stop" but it does not call clone_down().
- Add "ifname:sticky" keyword into $cloned_interfaces. If :sticky is
specified, the interface will not be destroyed in rc.d/netif stop.
- Add cloned_interfaces_sticky={YES,NO}. This variable globally sets
:sticky keyword above for all interfaces. The default value is NO.
When cloned_interfaces_sticky=YES, :nosticky keyword can be used to
override it on per interface basis.
device names "md" or "md[0-9]*" and a "file" option are specified in
/etc/fstab like this:
md none swap sw,file=/swap.bin 0 0
- Add GBDE/GELI encrypted swap space specification support, which
rc.d/encswap supported. The /etc/fstab lines are like the following:
/dev/ada1p1.bde none swap sw 0 0
/dev/ada1p2.eli none swap sw 0 0
.eli devices accepts aalgo, ealgo, keylen, and sectorsize as options.
swapctl(8) can understand an encrypted device in the command line
like this:
# swapctl -a /dev/ada2p1.bde
- "-L" flag is added to support "late" option to defer swapon until
rc.d/mountlate runs.
- rc.d script change:
rc.d/encswap -> removed
rc.d/addswap -> just display a warning message if $swapfile is defined
rc.d/swap1 -> renamed to rc.d/swap
rc.d/swaplate -> newly added to support "late" option
These changes alleviate a race condition between device creation/removal
and swapon/swapoff.
MFC after: 1 week
Reviewed by: wblock (manual page)
Not only this is a bit cleaner, it allows multiple instances of hostapd to be
running on the system host, useful for simultaneous dual-band WiFi.
This is similar to ifconfig_wlanX="WPA" but it uses /etc/hostapd-wlanX.conf.
Compatibility with hostapd_enable=YES/NO was kept.
Reviewed by: adrian
requests reload or restart, which, in addition of testing the
configuration, will also generate host keys when they are not
present (previous behavior).
Obtained from: FreeNAS
Ok'ed by: bdrewery, des
MFC after: 1 week
ntpdate_config was set to NULL the conditional would (counter to prevailing
logic) succeed -- leading to awk attempting to redirect from a NULL pathname
standard-in. While we're here, make the script consistant with itself by
removing the {curlies} around ntpdate_config (they are unnecessary).
{,ipv6_}static_routes and rc.d/routing. For example:
static_routes="foo bar:em0"
route_foo="-net 10.0.0.0/24 -gateway 192.168.2.1"
route_bar="-net 192.168.1.0/24 -gateway 192.168.0.2"
At boot time, all of the static routes are installed as before.
The differences are:
- "/etc/rc.d/netif start/stop <if>" now configures static routes
with :<if> if any.
- "/etc/rc.d/routing start/stop <af> <if>" works as well. <af> cannot be
omitted when <if> is specified, but a keyword "any" or "all" can be used
for <af> and <if>.
apply to most jails but do apply to vnet jails. This includes adding
a new sysctl "security.jail.vnet" to identify vnet jails.
PR: conf/149050
Submitted by: mdodd
MFC after: 3 days
Add netif as a requirement of syslogd to get lo0 up. Currently, this
doesn't affect the rc order, because mountcritremote already depends on
netif.
Reviewed by: eadler
Approved by: kenm (mentor)
MFC after: 2 weeks
- Use the absolute pathname for ip6addrctl.
- Use "install" instead of "add" to reduce the number of invocations.
Reported by: Tatsuki Makino [*]
PR: conf/175006 [*]
MFC after: 1 week
There are three situations where the sysctl script is called:
1. "start", very early
2. "lastload", near the end of rc
3. "reload", at admin request while the system is booted
Ignore unknown OIDs in situation 1 because kernel modules may not be loaded
yet and complain about them in situations 2 and 3.
PR: conf/174595
Submitted by: Olivier Smedts
space configured for rc.d/dumpon to designate for dumping -- then exit
silently rather than with a
> realpath: /dev/dumpdev: No such file or directory
error message.
An argument could be made that we should print a (more informative) warning
message; but given that under the same conditions the rc.d/dumpon script will
already print a
> No suitable dump device was found
warning, it seems that printing an additional
> Dump device does not exist. Savecore not run.
warning would be superfluous.
Do this per jail started, not per address. This will allow DAD to complete
and services to properly start. Before we have seen problems with services
trying to start before the IPv6 address was available to use and thus
erroring and failing to start.
MFC after: 3 days
provide dump directory. Eliminate this redundant argument. This changes
the usage, but the only risk here is that a warning will be printed
about directory given as device.
- Update usage of -C option.
- When clearing dump header from the given device there is also no need to
provide dump directory, although additional arguments for -c were not
documented.
- Document that -v can be used with -c and that list of devices can be given.
Obtained from: WHEEL Systems
auditdistd (distributed audit daemon) to the build:
- Manual cross references
- Makefile for auditdistd
- rc.d script, rc.conf entrie
- New group and user for auditdistd; associated aliases, etc.
The audit trail distribution daemon provides reliable,
cryptographically protected (and sandboxed) delivery of audit tails
from live clients to audit server hosts in order to both allow
centralised analysis, and improve resilience in the event of client
compromises: clients are not permitted to change trail contents
after submission.
Submitted by: pjd
Sponsored by: The FreeBSD Foundation (auditdistd)
Trying to determine current lowest C-state after an AC event is racy
with C-states actually being changed by ACPI platform and kernel driver.
MFC after: 3 weeks
systems are fully "ready to go".
'FILESYSTEMS' states: "This is a dummy dependency, for services which
require file systems to be mounted before starting." However, we have
'var' which is was run after 'FILESYSTEMS' and can mount /var if it
already isn't mounted. Furthermore, several scripts cannot use /var
until 'cleanvar' has done its thing. Thus "FILESYSTEMS" hasn't really
meant all critical file systems are fully usable.
gives machine unique values from the firmware.
* The kernel is more likely to be unique than /bin/ls (but no need to
stuff many megabytes into /dev/random, so hash it).
* Change ordering to give larger variance across reboots to reduce
predictability.
r128060 for "hardware-supplied entropy" reversed this without reason,
seems a typo.
* Isolate "better than nothing" implementation to a function.
Submitted by: obrien & Arthur Mesh <arthurmesh@gmail.com>
Sponsored by: Juniper Networks